Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P0115  Engine Coolant Temperature Circuit  P0117  Engine Coolant Temperature Circuit Low Input  P0118  Engine Coolant Temperature Circuit High Input  


DESCRIPTION

A thermistor is built into the engine coolant temperature sensor and it changes its resistance value according to the engine coolant temperature.

The structure of the sensor and connection to the ECM is the same as that of the intake air temperature sensor.

HINT:

If DTC P0115, P0117 or P0118 is stored, the ECM operates the fail-safe function in which the engine coolant temperature is assumed to be 80°C (176°F).


P0115
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 0.5 seconds Open or short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open or short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM



P0117
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 0.5 seconds Short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM



P0118
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 0.5 seconds Open in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM



Related Data List
DTC No. Data List
P0115
P0117
P0118
Coolant Temp

HINT:
·

If DTC P0115, P0117 and/or P0118 is stored, the following symptoms may appear:

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power


·

When DTC P0115, P0117 and/or P0118 is stored, check the engine coolant temperature by entering the following menus: Engine and ECT / Data List / Coolant Temp.

Reference
Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or higher Short circuit



WIRING DIAGRAM

A165735E24
0.583,2.448 0.875,2.604 0.292,0.156 10 false C71 0.583,2.604 2.958,2.792 2.375,0.188 10 false Engine Coolant Temperature Sensor 5.74,2.677 6.708,2.865 0.969,0.188 10 false C45*1, C46*2 5.74,2.844 6.094,3.021 0.354,0.177 10 false ECM 2.458,1.844 2.583,2.021 0.125,0.177 10 false 1 5.542,1.646 5.771,1.823 0.229,0.177 10 false E2 5.542,1.031 5.906,1.208 0.365,0.177 10 false THW 2.458,1.229 2.583,1.406 0.125,0.177 10 false 2 5.26,1.865 5.49,2.073 0.229,0.208 10 false 92 5.26,1.229 5.49,1.427 0.229,0.198 10 false 93 6.156,0.917 6.281,1.073 0.125,0.156 10 false R 6.25,0.635 6.51,0.802 0.26,0.167 10 false 5V 0.51,3.125 1.344,3.323 0.833,0.198 10 false *1: for LHD 0.5,3.438 1.333,3.635 0.833,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Data List / Coolant Temp.


d.

Read the value.

OK:

70 to 90°C (158 to 194°F) with warm engine


Result
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
70 to 90°C (158 to 194°F) C

HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F) or higher.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
U163319E02
0.656,0.323 0.854,0.521 0.198,0.198 10 false *1 0.198,2.552 0.375,2.75 0.177,0.198 10 false *a 2.406,1.635 2.615,1.865 0.208,0.229 10 false E2 2.552,0.302 2.74,0.531 0.188,0.229 10 false *2 2.417,1.25 2.865,1.479 0.448,0.229 10 false THW 0.698,3.49 1.073,3.698 0.375,0.208 10 false C71

Disconnect the engine coolant temperature sensor connector.


b.

Connect terminals 1 and 2 of the engine coolant temperature sensor wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Enter the following menus: Engine and ECT / Data List / Coolant Temp.


f.

Read the value.

OK:

140°C (284°F) or higher


Text in Illustration
*1 Engine Coolant Temperature Sensor
*2 ECM
*a Front view of wire harness connector
(to Engine Coolant Temperature Sensor)


g.

Reconnect the engine coolant temperature sensor connector.



OK

7.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR.

NG

3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C71-2 - C45-93 (THW) Always Below 1 Ω
C71-1 - C45-92 (E2) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
C71-2 - C46-93 (THW) Always Below 1 Ω
C71-1 - C46-92 (E2) Always Below 1 Ω



d.

Reconnect the engine coolant temperature sensor connector.


e.

Reconnect the ECM connector.



OK

9.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A378876E05
0.708,0.24 1.021,0.438 0.313,0.198 10 false *1 2.583,0.198 2.896,0.396 0.313,0.198 10 false *2 2.542,1.021 2.938,1.229 0.396,0.208 10 false THW 2.531,1.49 3.01,1.688 0.479,0.198 10 false E2

Disconnect the engine coolant temperature sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Engine and ECT / Data List / Coolant Temp.


e.

Read the value.

OK:

-40°C (-40°F)


Text in Illustration
*1 Engine Coolant Temperature Sensor
*2 ECM


f.

Reconnect the engine coolant temperature sensor connector.



OK

10.REPLACE ENGINE COOLANT TEMPERATURE SENSOR

NG

5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C71-2 or C45-93 (THW) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C71-2 or C46-93 (THW) - Body ground Always 10 kΩ or higher



d.

Reconnect the engine coolant temperature sensor connector.


e.

Reconnect the ECM connector.



OK

6.REPLACE ECM

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.REPLACE ECM

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR.
a.

Replace the engine coolant temperature sensor (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL).



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

Replace the engine coolant temperature sensor (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL).



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the ignition switch to ON for 1 second.


d.

Enter the following menus: Engine and ECT / Trouble Codes.


e.

Confirm that the DTC is not output again.



NEXT

END