Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate that the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and sets the DTC.

HINT:

The normal conditions are as shown in the table below.

Signals Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF


P0504
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Release and depress brake pedal with ignition switch ON Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch is ON.
(b) Brake pedal is released.
(c) The STP signal is off when the ST1- signal is off, or the STP signal is on when the ST1- signal is on.
·

Open or short in stop light switch signal circuit

·

STOP fuse

·

IGN fuse

·

Stop light switch

·

ECM



Related Data List
DTC No. Data List
P0504 Stop Light Switch

WIRING DIAGRAM

A160611E16
1.169,0.879 2.236,1.085 1.067,0.206 10 from IG2 Relay 1.357,1.866 2.238,2.073 0.881,0.206 10 from Battery 2.795,0.71 3.104,0.866 0.309,0.156 10 IGN 2.759,1.038 2.892,1.192 0.132,0.153 10 1 3.006,1.038 3.138,1.192 0.132,0.153 10 2 2.759,2.019 2.892,2.172 0.132,0.153 10 1 4.56,1.8 4.693,1.953 0.132,0.153 10 1 5.683,2.94 6.631,3.093 0.948,0.153 10 A38*1, A52*2 5.914,3.103 6.297,3.256 0.383,0.153 10 ECM 3.006,2.019 3.138,2.172 0.132,0.153 10 2 3.433,1.8 3.565,1.953 0.132,0.153 10 2 4.56,0.805 4.693,0.959 0.132,0.153 10 3 5.331,0.805 5.526,0.959 0.195,0.153 10 35 5.331,1.792 5.526,1.946 0.195,0.153 10 36 5.611,0.805 5.959,0.959 0.348,0.153 10 ST1- 5.611,1.793 5.959,1.946 0.348,0.153 10 STP 3.433,0.805 3.565,0.959 0.132,0.153 10 4 2.744,1.701 3.155,1.857 0.411,0.156 10 STOP 1.742,2.813 2.488,2.968 0.746,0.156 10 *1: for LHD 1.742,3.121 2.488,3.277 0.746,0.156 10 *2: for RHD 3.475,2.23 3.875,2.375 0.400,0.145 10 A30 3.475,2.391 4.614,2.578 1.139,0.187 10 Stop Light Switch

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

Stop light switch conditions can be checked using the intelligent tester.

(a)

Connect the intelligent tester to the DLC3.

(b)

Turn the ignition switch to ON.

(c)

Turn the tester on.

(d)

Enter the following menus: Powertrain / Engine / Data List / Stop Light Switch.

(e)

Check Stop Light Switch when the brake pedal is depressed and released.




Brake Pedal Operation Specified Condition
Depressed ON
Released OFF

PROCEDURE

1.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL B VOLTAGE)
a.
U163884E02
0.219,0.219 2.615,0.583 2.396,0.365 10 false Front view of wire harness connector: (to Stop Light Switch) 0.552,2.104 0.938,2.281 0.385,0.177 10 false A30

Disconnect the stop light switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A30-2 - Body ground Always 11 to 14 V
A30-4 - Body ground Ignition switch ON 11 to 14 V




OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

4.INSPECT FUSE (STOP, IGN)
2.INSPECT STOP LIGHT SWITCH ASSEMBLY
C171632E16
1.646,1.375 1.104,1.01 false 2.323,1.906 1.792,1.542 false 1.781,1.365 2.313,1 false 1.115,1.906 1.656,1.542 false 0.594,3.146 0.75,2.448 0.75,2.448 0.833,2.448 false 0.969,0.865 1.094,1.063 0.125,0.198 10 false 2 2.385,0.865 2.521,1.063 0.135,0.198 10 false 1 0.969,1.844 1.094,2.042 0.125,0.198 10 false 4 2.396,1.854 2.542,2.052 0.146,0.198 10 false 3 0.885,2.333 1.135,2.552 0.25,0.219 10 false Pin 0.031,3.792 0.563,4.156 0.531,0.365 10 false Not Pushed 0.792,3.792 1.323,3.99 0.531,0.198 10 false Pushed 0.219,0.042 2.781,0.406 2.563,0.365 10 false Component without harness connected: (Stop Light Switch)

a.

Remove the stop light switch.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Switch pin not pushed Below 1 Ω
Switch pin pushed 10 kΩ or higher
3 - 4 Switch pin not pushed 10 kΩ or higher
Switch pin pushed Below 1 Ω




OK

3.CHECK ECM (STP AND ST1- VOLTAGE)

NG

5.REPLACE STOP LIGHT SWITCH ASSEMBLY
3.CHECK ECM (STP AND ST1- VOLTAGE)
U162823E02
1.854,3.667 2.563,3.448 false 1.771,3.667 2.563,4.385 false 1.906,0.292 3.375,0.49 1.469,0.198 10 false Brake Pedal Released 0.125,0.302 1.646,0.521 1.521,0.219 10 false Brake Pedal Depressed 0.281,1.927 2.615,2.271 2.333,0.344 10 false Front view of wire harness connector: (to ECM) 2.615,3.323 3.292,3.51 0.677,0.188 10 false 36 (STP) 2.604,4.281 3.229,4.49 0.625,0.208 10 false 35 (ST1-) 1.146,2.708 1.479,2.906 0.333,0.198 10 false A38 0.052,3.99 0.781,4.167 0.729,0.177 10 false *1: for LHD 0.052,4.302 0.792,4.479 0.74,0.177 10 false *2: for RHD 1.458,2.563 1.625,2.708 0.167,0.146 10 false *1 1.958,2.708 2.25,2.885 0.292,0.177 10 false A52 2.313,2.563 2.479,2.708 0.167,0.146 10 false *2

a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Brake Pedal Condition Specified Condition
A38-35 (ST1-) - Body ground Released 11 to 14 V
Depressed 0 to 3 V
A38-36 (STP) - Body ground Released 0 to 3 V
Depressed 11 to 14 V

for RHD
Tester Connection Brake Pedal Condition Specified Condition
A52-35 (ST1-) - Body ground Released 11 to 14 V
Depressed 0 to 3 V
A52-36 (STP) - Body ground Released 0 to 3 V
Depressed 11 to 14 V




OK

6.REPLACE ECM

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.INSPECT FUSE (STOP, IGN)
a.

Remove the STOP and IGN fuses from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
STOP fuse Always Below 1 Ω
IGN fuse




OK

7.REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

8.CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
5.REPLACE STOP LIGHT SWITCH ASSEMBLY
a.

Replace the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE ECM

NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE

NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON and turn the tester on.


e.

Brake pedal released and depressed.


f.

Enter the following menus: Powertrain / Engine / DTC.


g.

Confirm that the DTC is not output again.



NEXT

END