Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2015.08–2016.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P0560  System Voltage  


DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the ECM memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.

P0560
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 3 seconds The voltage at terminal BATT drops excessively for 3 seconds and part of the stored values in the ECM are initialized.
(1 trip detection logic)
·

Open in backup power source circuit (to BATT terminal)

·

Battery

·

Battery terminals

·

EFI MAIN fuse

·

ECM



Related Data List
DTC No. Data List
P0560 Battery Voltage*

*: This is not the voltage at terminal BATT; it is the power supply voltage for the ECM.

HINT:

If DTC P0560 is stored, the ECM does not store other DTCs or the data stored in the ECM is partly cleared.


WIRING DIAGRAM

A375382E02
0.552,4.833 1.073,5.01 0.521,0.177 10 false Battery 2.99,4.969 3.792,5.146 0.802,0.177 10 false *1: for LHD 2.99,5.26 3.792,5.438 0.802,0.177 10 false *2: for RHD 2.927,1.438 3.177,1.594 0.25,0.156 10 false 1S 2.719,1.427 2.885,1.583 0.167,0.156 10 false 7 2.958,3.719 4.094,3.896 1.135,0.177 10 false Integration Relay 0.563,2.302 0.969,2.458 0.406,0.156 10 false P/I-B 1.917,2.302 2.958,2.458 1.042,0.156 10 false EFI MAIN NO.1 5.823,0.688 6.146,0.844 0.323,0.156 10 false 20*2 5.854,0.875 6.198,1.094 0.344,0.219 10 false A52 6.198,0.698 6.583,0.875 0.385,0.177 10 false BATT 5.854,2.167 6.167,2.344 0.313,0.177 10 false A52 6.198,2.135 6.417,2.313 0.219,0.177 10 false +B 5.854,2.719 6.188,2.906 0.333,0.188 10 false A52 5.51,0.688 5.833,0.844 0.323,0.156 10 false 20*1 5.521,0.875 5.854,1.083 0.333,0.208 10 false A38 5.552,1.969 5.802,2.125 0.25,0.156 10 false 2*1 5.875,1.969 6.125,2.125 0.25,0.156 10 false 2*2 5.521,2.167 5.865,2.375 0.344,0.208 10 false A38 5.5,2.531 5.854,2.698 0.354,0.167 10 false 44*1 5.844,2.531 6.229,2.698 0.385,0.167 10 false 44*2 5.521,2.719 5.844,2.896 0.323,0.177 10 false A38 4.625,1.969 4.844,2.125 0.219,0.156 10 false 11 4.625,2.167 4.875,2.344 0.25,0.177 10 false 1S 1.198,1.969 1.458,2.125 0.26,0.156 10 false 1*1 1.208,2.167 1.458,2.344 0.25,0.177 10 false 1Y 1.521,1.969 1.781,2.125 0.26,0.156 10 false 1*2 1.531,2.156 1.781,2.333 0.25,0.177 10 false 1X 4.677,2.531 4.833,2.688 0.156,0.156 10 false 8 4.635,2.719 4.875,2.896 0.24,0.177 10 false 1S 1.25,2.531 1.406,2.688 0.156,0.156 10 false 4 1.208,2.719 1.448,2.896 0.24,0.177 10 false 1S 6.198,2.698 6.635,2.875 0.438,0.177 10 false MREL 6.385,4.781 6.781,4.958 0.396,0.177 10 false ECM 5.844,3.646 6.188,3.802 0.344,0.156 10 false 81*2 5.854,3.833 6.135,4.01 0.281,0.177 10 false C46 5.51,3.646 5.854,3.802 0.344,0.156 10 false 81*1 5.521,3.833 5.802,4.01 0.281,0.177 10 false C45 6.198,3.802 6.438,3.979 0.24,0.177 10 false E1 5.865,1.563 6.177,1.75 0.313,0.188 10 false A52 6.208,1.542 6.521,1.719 0.313,0.177 10 false +B2 5.563,1.375 5.813,1.531 0.25,0.156 10 false 1*1 5.885,1.375 6.135,1.531 0.25,0.156 10 false 1*2 5.531,1.573 5.865,1.771 0.333,0.198 10 false A38 3.177,3.042 4.219,3.198 1.042,0.156 10 false EFI MAIN NO.1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION).



HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

When the ignition switch is turned to ON, even though +B voltage is present, when the voltage at terminal BATT (power supply for maintaining memorized values in the ECM) drops excessively, this DTC is stored.



PROCEDURE

1.CHECK ECM TERMINAL VOLTAGE (BATT)
a.
U163294E01
0.249,0.168 0.422,0.341 0.173,0.173 10 *a 1.968,1.835 2.769,1.995 0.801,0.160 10 20 (BATT) 1.551,1.001 1.929,1.895 false 0.308,0.653 0.589,0.795 0.281,0.142 10 A38 0.361,0.911 0.534,1.084 0.173,0.173 10 *A 0.299,1.246 0.580,1.388 0.281,0.142 10 A52 0.352,1.504 0.526,1.677 0.173,0.173 10 *B

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
A38-20 (BATT) - Body ground Always 11 to 14 V

for RHD
Tester Connection Condition Specified Condition
A52-20 (BATT) - Body ground Always 11 to 14 V


Text in Illustration
*A for LHD
*B for RHD
*a Front view of wire harness connector
(ECM)


c.

Reconnect the ECM connector.



OK

2.INSPECT BATTERY

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.INSPECT BATTERY
a.

Check that the battery is not depleted (See page Power Source / Network>1VD-FTV (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION).

OK:

Battery is not depleted.




OK

3.CHECK BATTERY TERMINAL

NG

7.RECHARGE OR REPLACE BATTERY
3.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded.




OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

8.REPAIR OR REPLACE BATTERY TERMINAL
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON for 3 seconds.


f.

Enter the following menus: Engine and ECT / Trouble Codes.


g.

Read the DTCs.

Result
Result Proceed to
P0560 is output A
No DTC is output B



A

5.REPLACE ECM

B

END

5.REPLACE ECM

NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.RECHARGE OR REPLACE BATTERY
a.

Recharge or replace the battery.



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE BATTERY TERMINAL
a.

Repair or replace the battery terminal.



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON for 3 seconds.


e.

Enter the following menus: Engine and ECT / Trouble Codes.


f.

Confirm that the DTC is not output again.



NEXT

END