Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) J

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  Injector Circuit  


DESCRIPTION

The injector driver drives the injectors at high speeds with a high-voltage DC/DC converter. The ECM constantly monitors the injector driver and stops the engine if an abnormal condition is detected.

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.
U162836E02
1.073,1.563 0.792,1.969 false 2.313,3.5 2.521,3.948 false 0.344,0.917 0.646,1.115 0.302,0.198 10 false C73 0.677,0.781 0.896,0.958 0.219,0.177 10 false *b 0.344,1.229 0.635,1.396 0.292,0.167 10 false C75 0.677,1.073 0.906,1.25 0.229,0.177 10 false *c 0.344,2.698 0.615,2.865 0.271,0.167 10 false C74 0.677,2.563 0.885,2.74 0.208,0.177 10 false *b 0.344,3.021 0.646,3.198 0.302,0.177 10 false C76 0.677,2.885 0.896,3.073 0.219,0.188 10 false *c 0.573,1.979 0.948,2.208 0.375,0.229 10 false GND 2.417,3.958 2.792,4.188 0.375,0.229 10 false +B 0.146,0.031 0.354,0.24 0.208,0.208 10 false *a

Disconnect the EDU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
No. 1
Tester Connection Condition Specified Condition
C74-8 (+B) - C73-1 (GND) Ignition switch ON 11 to 14 V

No. 2
Tester Connection Condition Specified Condition
C76-8 (+B) - C75-1 (GND) Ignition switch ON 11 to 14 V



*a Front view of wire harness connector
(to Injector Driver)
*b for No. 1
*c for No. 2

c.

Reconnect the injector driver connectors.



OK

NG

2.INSPECT EDU RELAY
2.INSPECT EDU RELAY

OK

3.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER - INTEGRATION RELAY)

NG

REPLACE EDU RELAY

3.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER - INTEGRATION RELAY)
a.

Remove the integration relay from the engine room relay block.


b.

Remove the EDU relay (EDU NO. 1 or EDU NO. 2).


c.

Disconnect the ECM connector.


d.

Disconnect the injector driver connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for No. 1
Tester Connection Condition Specified Condition
1S-11 - EDU NO. 1 relay (1) Always Below 1 Ω
C74-8 (+B) - EDU NO. 1 relay (5) Always Below 1 Ω
1S-11 or EDU NO. 1 relay (1) - Body ground Always 10 kΩ or higher
C74-8 (+B) or EDU NO. 1 relay (5) - Body ground Always 10 kΩ or higher

for No. 2
Tester Connection Condition Specified Condition
1P-12 - EDU NO. 2 relay (1) Always Below 1 Ω
C76-8 (+B) - EDU NO. 2 relay (5) Always Below 1 Ω
1P-12 - EDU NO. 2 relay (1) - Body ground Always 10 kΩ or higher
C76-8 (+B) or EDU NO. 2 relay (5) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (ECM - INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECM - INTEGRATION RELAY)
a.

Remove the integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (No. 1):
for LHD
Tester Connection Condition Specified Condition
A38-45 (IREL) - EDU NO. 1 relay (2) Always Below 1 Ω
A38-45 (IREL) or EDU NO. 1 relay (2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A52-45 (IREL) - EDU NO. 1 relay (2) Always Below 1 Ω
A52-45 (IREL) or EDU NO. 1 relay (2) - Body ground Always 10 kΩ or higher


Standard Resistance (No. 2):
for LHD
Tester Connection Condition Specified Condition
A38-46 (IRL2) - EDU NO. 2 relay (2) Always Below 1 Ω
A38-46 (IRL2) or EDU NO. 2 relay (2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A52-46 (IRL2) - EDU NO. 2 relay (2) Always Below 1 Ω
A52-46 (IRL2) or EDU NO. 2 relay (2) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reinstall the integration relay.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR