Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › RELAY › from 2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254997 RELAY G

1VD-FTV ENGINE CONTROL  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT FUEL PUMP RELAY (SUB PUMP)

a.
A184106E08
2.542,1.115 2.938,1.115 false 2.542,1.615 2.948,1.615 false 1.573,0.177 1.698,0.177 1.698,0.177 2.031,0.563 false 3.031,0.177 2.906,0.177 2.906,0.177 2.625,0.552 false 0.208,0.729 0.417,0.906 0.208,0.177 10 false 3 1.208,0.729 1.406,0.906 0.198,0.177 10 false 5 0.208,1.271 0.365,1.448 0.156,0.177 10 false 2 1.208,1.271 1.438,1.448 0.229,0.177 10 false 1 3.021,1.521 3.229,1.698 0.208,0.177 10 false 3 3,1.021 3.198,1.198 0.198,0.177 10 false 5 3.094,0.083 3.25,0.26 0.156,0.177 10 false 2 1.417,0.083 1.646,0.26 0.229,0.177 10 false 1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the fuel pump relay.


Hide 2.INSPECT EDU RELAY (EDU1)

A184106E08
2.542,1.115 2.938,1.115 false 2.542,1.615 2.948,1.615 false 1.573,0.177 1.698,0.177 1.698,0.177 2.031,0.563 false 3.031,0.177 2.906,0.177 2.906,0.177 2.625,0.552 false 0.208,0.729 0.417,0.906 0.208,0.177 10 false 3 1.208,0.729 1.406,0.906 0.198,0.177 10 false 5 0.208,1.271 0.365,1.448 0.156,0.177 10 false 2 1.208,1.271 1.438,1.448 0.229,0.177 10 false 1 3.021,1.521 3.229,1.698 0.208,0.177 10 false 3 3,1.021 3.198,1.198 0.198,0.177 10 false 5 3.094,0.083 3.25,0.26 0.156,0.177 10 false 2 1.417,0.083 1.646,0.26 0.229,0.177 10 false 1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied between 1 and 2 10 kΩ or higher
Battery voltage is applied between 1 and 2 Below 1 Ω


If the result is not as specified, replace the EDU relay.


Hide 3.INSTALL EDU RELAY (EDU2)

A184106E08
2.542,1.115 2.938,1.115 false 2.542,1.615 2.948,1.615 false 1.573,0.177 1.698,0.177 1.698,0.177 2.031,0.563 false 3.031,0.177 2.906,0.177 2.906,0.177 2.625,0.552 false 0.208,0.729 0.417,0.906 0.208,0.177 10 false 3 1.208,0.729 1.406,0.906 0.198,0.177 10 false 5 0.208,1.271 0.365,1.448 0.156,0.177 10 false 2 1.208,1.271 1.438,1.448 0.229,0.177 10 false 1 3.021,1.521 3.229,1.698 0.208,0.177 10 false 3 3,1.021 3.198,1.198 0.198,0.177 10 false 5 3.094,0.083 3.25,0.26 0.156,0.177 10 false 2 1.417,0.083 1.646,0.26 0.229,0.177 10 false 1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied between 1 and 2 10 kΩ or higher
Battery voltage is applied between 1 and 2 Below 1 Ω


If the result is not as specified, replace the EDU relay.


Hide 28371 4.INSPECT NO. 1 IGNITION RELAY (IG1)

a.
A111813E06
2.851,0.206 3.006,0.376 0.156,0.170 10 1 0.406,1.183 0.562,1.353 0.156,0.170 10 1 1.699,0.974 1.855,1.144 0.156,0.170 10 3 0.406,0.785 0.562,0.955 0.156,0.170 10 3 2.428,1.766 2.584,1.936 0.156,0.170 10 2 1.315,1.181 1.471,1.351 0.156,0.170 10 2 3.206,0.968 3.362,1.138 0.156,0.170 10 5 1.315,0.773 1.471,0.943 0.156,0.170 10 5 2.444,0.695 2.787,0.321 false 2.856,1.054 3.177,1.054 false 2.085,1.054 1.836,1.054 false 2.49,1.413 2.49,1.766 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the No. 1 ignition relay.


Hide 5.INSPECT INTEGRATION RELAY (A/F RELAY) (w/ DPF)

a.

Measure the resistance of the A/F HTR fuse.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A/F HTR fuse Always Below 1 Ω


If the result is not as specified, replace the A/F HTR fuse.



b.

Measure the resistance of the ignition relay air fuel ratio sensor relay circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Item Tester Connection Condition Specified Condition
for LHD 1Y-1 - 1S-3 Battery voltage is not applied to terminals 1S-1 and 1S-4 10 kΩ or higher
Battery voltage is applied to terminals 1S-1 and 1S-4 Below 1 Ω
for RHD 1X-1 - 1S-3 Battery voltage is not applied to terminals 1S-1 and 1S-4 10 kΩ or higher
Battery voltage is applied to terminals 1S-1 and 1S-4 Below 1 Ω


A385397E01
4.24,0.698 4.615,0.948 0.375,0.25 5.302,0.677 5.656,0.917 0.354,0.24 5.313,0.396 5.667,0.635 0.354,0.24 5.479,2.115 5.479,1.448 false 4.833,2.167 4.833,1.927 4.833,1.927 4.708,1.5 false 4.229,2.167 4.229,1.969 4.229,1.969 4.344,1.479 false 4.458,2.156 4.458,1.49 false 4.323,0.74 4.635,0.938 0.313,0.198 10 false 1S 5.385,0.719 5.698,0.917 0.313,0.198 10 false 1X 5.375,0.438 5.688,0.635 0.313,0.198 10 false 1Y 5.719,0.438 6.031,0.635 0.313,0.198 10 false *A 5.719,0.708 6.031,0.906 0.313,0.198 10 false *B 5.448,2.188 5.615,2.385 0.167,0.198 10 false 1 4.802,2.208 4.917,2.438 0.115,0.229 10 false 2 4.427,2.208 4.542,2.438 0.115,0.229 10 false 3 4.198,2.198 4.313,2.427 0.115,0.229 10 false 4 0.156,0.115 0.469,0.313 0.313,0.198 10 false *a

Text in Illustration
*A for LHD *B for RHD
*a Component without harness connected
(Integration Relay)
- -

If the result is not as specified, replace the integration relay.



Hide 6.INSPECT INTEGRATION RELAY (IG2 MAIN RELAY)

a.

Measure the resistance of the IG2 MAIN fuse.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IG2 MAIN fuse Always Below 1 Ω


If the result is not as specified, replace the IG2 MAIN fuse.



b.

Measure the resistance of the IG2 MAIN relay circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Item Tester Connection Condition Specified Condition
for LHD 1Y-1 - 1R-1 Battery voltage is not applied to terminals 1R-2 and 1S-4 10 kΩ or higher
Battery voltage is applied to terminals 1R-2 and 1S-4 Below 1 Ω
for RHD 1X-1 - 1R-1 Battery voltage is not applied to terminals 1R-2 and 1S-4 10 kΩ or higher
Battery voltage is applied to terminals 1R-2 and 1S-4 Below 1 Ω


A385399E01
3.5,0.708 3.833,0.948 0.333,0.24 4.219,0.708 4.552,0.948 0.333,0.24 5.292,0.708 5.625,0.948 0.333,0.24 5.292,0.427 5.625,0.667 0.333,0.24 5.49,1.448 5.49,2.031 false 4.344,1.5 4.344,2.083 false 3.698,1.51 3.521,2.021 3.521,2.021 3.521,2.146 false 3.792,1.5 3.969,2.021 3.969,2.021 3.969,2.146 false 0.167,0.156 0.479,0.354 0.313,0.198 10 false *a 3.563,0.74 3.875,0.938 0.313,0.198 10 false 1R 4.281,0.74 4.594,0.938 0.313,0.198 10 false 1S 5.365,0.75 5.677,0.948 0.313,0.198 10 false 1X 5.365,0.469 5.677,0.667 0.313,0.198 10 false 1Y 5.677,0.469 5.99,0.667 0.313,0.198 10 false *A 5.688,0.729 6,0.927 0.313,0.198 10 false *B 5.438,2.083 5.615,2.292 0.177,0.208 10 false 1 4.313,2.115 4.49,2.323 0.177,0.208 10 false 4 3.5,2.198 3.677,2.406 0.177,0.208 10 false 2 3.927,2.198 4.104,2.406 0.177,0.208 10 false 1

Text in Illustration
*A for LHD *B for RHD
*a Component without harness connected
(Integration Relay)
- -

If the result is not as specified, replace the integration relay.



Hide 7.INSPECT INTEGRATION RELAY (EFI MAIN NO.1 RELAY)

a.

Measure the resistance of the EFI MAIN NO. 1 fuse and EFI NO. 2 fuse.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI MAIN NO. 1 fuse Always Below 1 Ω
EFI NO. 2 fuse Always Below 1 Ω


If the result is not as specified, replace the EFI MAIN NO. 1 fuse and/or EFI NO. 2 fuse.



b.

Measure the resistance of the EFI MAIN No. 1 relay circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Item Tester Connection Condition Specified Condition
for LHD 1Y-1 - 1S-1 Battery voltage is not applied to terminals 1S-8 and 1S-4 10 kΩ or higher
Battery voltage is applied to terminals 1S-8 and 1S-4 Below 1 Ω
for RHD 1X-1 - 1S-1 Battery voltage is not applied to terminals 1S-8 and 1S-4 10 kΩ or higher
Battery voltage is applied to terminals 1S-8 and 1S-4 Below 1 Ω


A385400E01
4.219,0.698 4.563,0.938 0.344,0.24 5.323,0.719 5.646,0.938 0.323,0.219 5.323,0.448 5.646,0.667 0.323,0.219 5.479,2.021 5.479,1.448 false 4.552,2.073 4.552,1.573 false 4.135,2.094 4.135,1.927 4.135,1.927 4.333,1.49 false 4.813,2.073 4.813,1.948 4.813,1.948 4.677,1.49 false 0.167,0.125 0.479,0.323 0.313,0.198 10 false *a 4.292,0.74 4.604,0.938 0.313,0.198 10 false 1S 5.385,0.75 5.698,0.948 0.313,0.198 10 false 1X 5.375,0.49 5.688,0.688 0.313,0.198 10 false 1Y 5.698,0.75 5.948,0.917 0.25,0.167 10 false *B 5.698,0.479 5.948,0.646 0.25,0.167 10 false *A 5.438,2.083 5.604,2.292 0.167,0.208 10 false 1 4.521,2.094 4.688,2.302 0.167,0.208 10 false 8 4.104,2.094 4.271,2.302 0.167,0.208 10 false 4 4.781,2.104 4.948,2.313 0.167,0.208 10 false 1

Text in Illustration
*A for LHD *B for RHD
*a Component without harness connected
(Integration Relay)
- -

If the result is not as specified, replace the integration relay.



Hide 8.INSPECT INTEGRATION RELAY (EFI MAIN NO. 2 RELAY)

a.

Measure the resistance of the EFI MAIN NO. 2 fuse.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI MAIN NO. 2 fuse Always Below 1 Ω


If the result is not as specified, replace the EFI MAIN NO. 2 fuse.



b.

Measure the resistance of the EFI MAIN No. 2 relay circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Item Tester Connection Condition Specified Condition
for LHD 1Y-1 - 1P-12 Battery voltage is not applied to terminals 1P-8 and 1P-11 10 kΩ or higher
Battery voltage is applied to terminals 1P-8 and 1P-11 Below 1 Ω
for RHD 1X-1 - 1P-12 Battery voltage is not applied to terminals 1P-8 and 1P-11 10 kΩ or higher
Battery voltage is applied to terminals 1P-8 and 1P-11 Below 1 Ω


A385401E01
1.719,0.677 2.031,0.917 0.313,0.24 5.344,0.677 5.656,0.917 0.313,0.24 5.354,0.375 5.667,0.615 0.313,0.24 5.51,1.417 5.51,2.01 false 1.688,1.563 1.688,2.156 false 2.031,1.563 2.219,2.01 2.219,2.01 2.219,2.167 false 1.583,1.573 1.427,1.948 1.427,1.948 1.427,2.135 false 0.177,0.135 0.49,0.333 0.313,0.198 10 false *a 1.781,0.719 2.094,0.917 0.313,0.198 10 false 1P 5.406,0.719 5.719,0.917 0.313,0.198 10 false 1X 5.406,0.417 5.719,0.615 0.313,0.198 10 false 1Y 5.719,0.396 6.031,0.594 0.313,0.198 10 false *A 5.719,0.708 6.031,0.906 0.313,0.198 10 false *B 1.354,2.167 1.563,2.365 0.208,0.198 10 false 12 1.615,2.188 1.823,2.385 0.208,0.198 10 false 11 2.188,2.198 2.396,2.396 0.208,0.198 10 false 8 5.469,2.063 5.677,2.26 0.208,0.198 10 false 1

Text in Illustration
*A for LHD *B for RHD
*a Component without harness connected
(Integration Relay)
- -

If the result is not as specified, replace the integration relay.



Hide 9.INSPECT MAIN BODY ECU (IG1 NO. 1)

a.

Measure the resistance of the ECU-IG NO. 2 fuse.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ECU-IG NO. 2 fuse Always Below 1 Ω


If the result is not as specified, replace the ECU IG NO. 2 fuse.



b.

Measure the resistance of the IG1 No. 1 relay circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2G-1 - 2H-24 Battery voltage not applied between 2I-18 and 2J-1 10 kΩ or higher
Battery voltage applied between 2I-18 and 2J-1 Below 1 Ω


U163823E02
1.771,1.146 1.771,1.594 false 1.802,3.354 1.802,4.135 false 3.427,3.229 3.427,4.135 false 2.688,0.844 2.688,1.594 false 2.604,1.604 2.813,1.771 0.208,0.167 10 false 24 0.156,0.125 0.406,0.302 0.25,0.177 10 false *a 1.729,1.604 1.854,1.781 0.125,0.177 10 false 1 1.76,4.146 1.885,4.323 0.125,0.177 10 false 1 3.354,4.146 3.594,4.323 0.24,0.177 10 false 18 1.667,0.313 1.938,0.531 0.271,0.219 10 false 2G 2.76,0.302 3.063,0.49 0.302,0.188 10 false 2H 2.125,2.531 2.396,2.719 0.271,0.188 10 false 2J 3.979,2.531 4.208,2.719 0.229,0.188 10 false 2I

Text in Illustration
*a Component without harness connected
Main Body ECU (Cowl Side Junction Block LH)
- -

If the result is not as specified, replace the main body ECU.



Hide 28610 11.INSPECT NO. 1 GLOW RELAY (GLOW NO. 1)

Hide 28610 12.INSPECT NO. 2 GLOW RELAY (GLOW NO. 2)

Hide 82733A 13.INSPECT MAIN BODY ECU (ACC RELAY)