Refer to DTC P0107 (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>P0107).
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| After warming up engine, idle engine for 10 seconds or more, and then drive vehicle under load (accelerator opening amount 15% or more) with engine speed at 6000 rpm or less for 10 seconds | Either condition is met (2 trip detection logic):
(a) The manifold absolute pressure output is 2.5 V or higher for 10 seconds when idling the engine after warming it up. (b) The manifold absolute pressure sensor output is 0.25 V or less for 10 seconds when the accelerator opening amount is 15% or more and the engine speed is 6000 rpm or less. |
·
Vacuum hose connection ·
Manifold absolute pressure sensor |
| DTC No. | Data List |
|---|---|
| P0106 | MAP |
If DTC P0106 is stored, the following symptoms may appear:
Misfire
Combustion noise
Black smoke
White smoke
Lack of power
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P0106 is output | A |
| P0106 and other DTCs are output | B |
A
B
(See pageEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DIAGNOSTIC TROUBLE CODE CHART)
Check the vacuum hose connections.
Vacuum hose is connected correctly and is not damaged.
OK
NG
Replace the manifold absolute pressure sensor (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL).
NEXT
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DTC CHECK / CLEAR).
Turn the ignition switch off for 30 seconds or more.
Start the engine.
After warming up the engine, idle the engine for 10 seconds or more, and then drive the vehicle under load (accelerator opening angle 15% or more) with the engine speed at 6000 rpm or less for 10 seconds or more.
Confirm that the pending DTC is not output again.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Engine and ECT / Utility / All Readiness.
Input DTC P0106.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, drive the vehicle for 5 minutes, idle the engine for 5 minutes, and then check "All Readiness" again.
NEXT