| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Idling for 1 second | Even though the CPU (command area inside the ECU) is outputting the suction control valve operation duty, the output monitor signal is absent for 0.5 seconds.
(1 trip detection logic) |
·
Open or short in suction control valve circuit ·
Suction control valve (fuel supply pump assembly) ·
ECM |
| DTC No. | Data List |
|---|---|
| P0627 | ·
Common Rail Pressure ·
Target Common Rail Pressure |
For more information on the fuel supply pump assembly (suction control valve) and common rail system, refer to System Description (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>SYSTEM DESCRIPTION).
When DTC P0627 is stored, check the internal fuel pressure of the common rail by entering the following menus on the GTS: Engine and ECT / Data List / Common Rail Pressure.
Under a stable operating condition such as idling, Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure.
Refer to DTC P0088 (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>P0088).
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Disconnect the suction control valve connector.
| *1 | Fuel Supply Pump Assembly |
| *2 | Suction Control Valve |
Measure the resistance of the suction control valve.
No open or short circuit malfunction.
OK
NG
Disconnect the suction control valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z64-1 (+B) - C45- 104 (PCV+) | Always | Below 1 Ω |
| z64-2 (PCV) - C45-105 (PCV-) | Always | Below 1 Ω |
| z64-1 (+B) or C45- 104 (PCV+) - Body ground | Always | 10 kΩ or higher |
| z64-2 (PCV) or C45-105 (PCV-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z64-1 (+B) - C46- 104 (PCV+) | Always | Below 1 Ω |
| z64-2 (PCV) - C46-105 (PCV-) | Always | Below 1 Ω |
| z64-1 (+B) or C46- 104 (PCV+) - Body ground | Always | 10 kΩ or higher |
| z64-2 (PCV) or C46-105 (PCV-) - Body ground | Always | 10 kΩ or higher |
Reconnect the suction control valve connector.
Reconnect the ECM connector.
OK
NG
Connect the GTS to the DLC3
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DTC CHECK / CLEAR).
Start the engine and idle it for 1 second or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| No DTC is output | A |
| P0627 is output | B |
A
B
Replace the fuel supply pump assembly (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL).
NEXT
Bleed the air from the fuel system (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SYSTEM(w/o DPF)>ON-VEHICLE INSPECTION).
When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.
NEXT
Perform supply pump initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).
NEXT
Replace the ECM (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Repair or replace the harness or connector.
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DTC CHECK / CLEAR).
Turn the ignition switch off for 30 seconds or more.
Start the engine and idle it for 1 second or more.
Confirm that the DTC is not output again.
NEXT