Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P1229  Fuel Pump System  


DESCRIPTION

P1229
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Idling for 60 seconds The actual fuel pressure exceeds the target fuel pressure by 5000 kPa or more for 30 seconds.
(1 trip detection logic)
·

Short in suction control valve circuit

·

Suction control valve (fuel supply pump assembly)

·

Fuel pressure sensor (common rail assembly (for bank 1))

·

ECM



Related Data List
DTC No. Data List
P1229
·

Common Rail Pressure

·

Target Common Rail Pressure

·

Injection Pressure Correction

·

Target Pump SCV Current

·

Pump SCV Learning Value



HINT:
·

For more information on the fuel supply pump assembly (suction control valve) and common rail system, refer to System Description (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>SYSTEM DESCRIPTION).

·

When DTC P1229 is stored, check the internal fuel pressure of the common rail assembly by entering the following menus: Engine and ECT / Data List / Common Rail Pressure, Target Common Rail Pressure.

Under a stable condition such as idling after warming up the engine, Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure when normal.

·

When there is a problem with the movement of the fuel supply pump assembly (when Common Rail Pressure is higher than Target Common Rail Pressure due to a problem in which the suction valve has difficulty closing), the values of Injection Pressure Correction and Target Pump SCV Current decrease.



MONITOR DESCRIPTION

P1229 (Fuel overfeed):

The ECM stores this DTC if the actual fuel pressure inside the common rail remains higher than the target fuel pressure, despite the ECM closing the suction control valve. This DTC indicates that the suction control valve may be stuck open, or there may be a short in its circuit.

If this DTC is stored, the ECM enters fail-safe mode and limits the engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION).



HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

When this DTC is stored, be sure to carefully examine "Common Rail Pressure", "Target Common Rail Pressure", "Target Pump SCV Current", and "Pump SCV Learning Value" in the freeze frame data.



PROCEDURE

1.CHECK OTHER DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
P1229 and "P0190, P0192 and/or P0193" are output B
Except above A



A

2.READ VALUE USING GTS (COMMON RAIL PRESSURE AND TARGET COMMON RAIL PRESSURE)

B

GO TO FUEL RAIL PRESSURE SENSOR CIRCUIT

2.READ VALUE USING GTS (COMMON RAIL PRESSURE AND TARGET COMMON RAIL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Common Rail Pressure and Target Common Rail Pressure.


e.

Check that the internal fuel pressure of the common rail assembly is within the specification below.

OK:

Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure when engine is idling after warming up the engine.




OK

NG

3.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
3.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
a.

Disconnect the suction control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
z64-1 (+B) - C45- 104 (PCV+) Always Below 1 Ω
z64-2 (PCV) - C45-105 (PCV-) Always Below 1 Ω
z64-1 (+B) or C45- 104 (PCV+) - Body ground Always 10 kΩ or higher
z64-2 (PCV) or C45-105 (PCV-) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
z64-1 (+B) - C46- 104 (PCV+) Always Below 1 Ω
z64-2 (PCV) - C46-105 (PCV-) Always Below 1 Ω
z64-1 (+B) or C46- 104 (PCV+) - Body ground Always 10 kΩ or higher
z64-2 (PCV) or C46-105 (PCV-) - Body ground Always 10 kΩ or higher



d.

Reconnect the suction control valve connector.


e.

Reconnect the ECM connector.



OK

6.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

5.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
5.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Data List / Common Rail Pressure and Target Common Rail Pressure.


d.

Take a snapshot with the GTS during the Active Test.


e.

Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Common Rail Pressure) when the "Test the Fuel Leak" Active Test is performed (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DATA LIST / ACTIVE TEST).

HINT:

In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


A227749E58
3.604,2.427 3.719,1.948 3.719,1.948 3.792,1.948 false 4.604,2.594 4.948,2.333 4.948,2.333 5,2.333 false 3.521,2.542 3.24,1.896 3.24,1.896 3.188,1.896 false 3.573,3.24 3.813,4.302 3.813,4.302 3.938,4.302 false 0.083,1.417 1.448,1.573 1.365,0.156 10 false Active Test Operation 0.083,0.583 1.479,0.781 1.396,0.198 10 false Engine Speed (rpm) 0.083,3.25 1.677,3.49 1.594,0.24 10 false Common Rail Pressure 3.813,1.865 5.75,2.031 1.938,0.167 10 false Target Common Rail Pressure 6.469,4.125 6.865,4.302 0.396,0.177 10 false Time 2.125,2.406 2.865,2.771 0.74,0.365 10 false Less than 10000 kPa 3,4.26 3.688,4.427 0.688,0.167 10 false 2 seconds 5.052,2.208 6.281,2.604 1.229,0.396 10 false Abnormal Common Rail Pressure 2.448,1.115 3.125,1.313 0.677,0.198 10 false Test Start 4.177,1.115 4.844,1.313 0.667,0.198 10 false Test Stop 5.625,1.115 6.302,1.313 0.677,0.198 10 false Test Start 2.083,1.813 3.229,2.135 1.146,0.323 10 false Normal Common Rail Pressure 1.646,0.271 2.021,0.438 0.375,0.167 10 false 2000 1.885,0.833 2.052,1 0.167,0.167 10 false 0 1.75,1.302 2.073,1.469 0.323,0.167 10 false ON 1.698,1.552 2.021,1.719 0.323,0.167 10 false OFF 4.01,4.24 6.323,4.583 2.313,0.344 10 false Pressure Discharge Valve Abnormal Common Rail Pressure

OK:

The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.


HINT:
·

"Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.

·

"Common Rail Pressure" is the actual fuel pressure.



Result
Result Proceed to
The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa. B
Except above A



A

6.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER

B

10.CHECK CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER
a.

Clean the fuel filter case and replace the fuel filter.

HINT:

Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.




NEXT

7.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
7.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
a.

Replace the fuel supply pump assembly (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL).



NEXT

8.BLEED AIR FROM FUEL SYSTEM
8.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SYSTEM(w/o DPF)>ON-VEHICLE INSPECTION).

HINT:

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.




NEXT

9.PERFORM SUPPLY PUMP INITIALIZATION
9.PERFORM SUPPLY PUMP INITIALIZATION

NEXT

10.CHECK CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CHECK CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine.


e.

Idle the engine for 60 seconds, and then run it at 2500 rpm without load for 60 seconds.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Engine and ECT / Utility / All Readiness.


ii.

Input DTC P1229.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, increase the idling time.




NEXT

END