Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P0046  Turbocharger / Supercharger Boost Control Solenoid Circuit Range / Performance  P0047  Turbocharger/Supercharger Boost Control "A" Circuit Low  P0048  Turbocharger/Supercharger Boost Control "A" Circuit High  P004B  Turbocharger/Supercharger Boost Control Solenoid "B" Circuit Range/Performance  P004C  Turbocharger/Supercharger Boost Control Solenoid "B" Circuit Low  P004D  Turbocharger/Supercharger Boost Control Solenoid "B" Circuit High  


DESCRIPTION

These DTCs indicate that the DC motor of the turbocharger is malfunctioning. The ECM monitors the DC motor current to detect an open or short in the DC motor circuit. If the current meets certain criteria, the ECM stores a DTC and illuminates the MIL immediately.

The DC motor is used to operate the nozzle vane of the turbocharger. The nozzle vane opens and closes to change the velocity of exhaust emissions in order to control the turbo pressure. The ECM varies the duty ratio of the DC motor in accordance with the driving conditions.

If the nozzle vane is stuck closed (DC motor stuck off), drivability may deteriorate at wide open throttle. If the nozzle vane is stuck open (DC motor stuck on), drivability may deteriorate at intermediate throttle positions or the engine power may be insufficient.

P0046 (Bank 1), P004B (Bank 2)
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 5 seconds Either of the following conditions are met when the motor is driving (1 trip detection logic):
·

DC motor duty ratio is +/-100% for 1.3 seconds or more.

·

DC motor current is 2.2 A or more for 5 seconds or more.


·

Open or short in DC motor (turbocharger sub-assembly) circuit

·

DC motor (turbocharger sub-assembly)

·

Turbocharger nozzle vane is stuck or movement is irregular



P0047 (Bank 1), P004C (Bank 2)
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
2 seconds after engine is started, race engine for 1 second The DC motor duty ratio is 80% or more and the motor current is 0.5 A or less for 3 seconds or more (1 trip detection logic).
·

Open in DC motor (turbocharger sub-assembly) circuit

·

DC motor (turbocharger sub-assembly)

·

Turbocharger nozzle vane is stuck or movement is irregular



P0048 (Bank 1), P004D (Bank 2)
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
2 seconds after engine is started, race engine for 1 second Overcurrent is detected 25 times or more (0.4 seconds or more) (1 trip detection logic).
·

Short in DC motor (turbocharger sub-assembly) circuit

·

DC motor (turbocharger sub-assembly)

·

Turbocharger nozzle vane is stuck or movement is irregular



HINT:

If DTC P0046, P0047, P0048, P004B, P004C or P004D is stored, the following symptom may appear.

·

Stuck closed malfunction:

- Vehicle surge when driving with full load

·

Stuck open malfunction:

- Lack of power

- Vehicle surge or hesitation under light or medium load



WIRING DIAGRAM

A275247E02
5.198,0.618 5.399,0.801 0.201,0.184 10 86 5.198,1.374 5.399,1.558 0.201,0.184 10 85 5.198,3.308 5.399,3.491 0.201,0.184 10 41 5.198,2.572 5.399,2.756 0.201,0.184 10 18 5.665,4.249 6.612,4.414 0.948,0.165 10 C45*1, C46*2 5.954,4.524 6.300,4.680 0.346,0.156 10 ECM 0.308,1.801 3.645,2.034 3.336,0.232 10 DC Motor (Turbocharger sub-assembly) (for Bank 1) 0.308,1.556 0.617,1.726 0.309,0.170 10 C90 0.308,3.805 3.645,4.037 3.336,0.232 10 DC Motor (Turbocharger sub-assembly) (for Bank 2) 0.308,3.56 0.610,3.730 0.302,0.170 10 z67 1.222,0.817 1.476,0.966 0.253,0.149 10 M+ 1.222,1.357 1.476,1.506 0.253,0.149 10 M- 1.527,0.59 1.655,0.773 0.128,0.184 10 2 1.555,1.549 1.683,1.733 0.128,0.184 10 1 5.517,0.698 5.770,0.847 0.253,0.149 10 M+ 5.517,1.448 5.770,1.597 0.253,0.149 10 M- 1.177,2.807 1.486,2.956 0.309,0.149 10 M2+ 1.177,3.346 1.486,3.495 0.309,0.149 10 M2- 1.524,2.579 1.652,2.763 0.128,0.184 10 2 1.552,3.539 1.680,3.722 0.128,0.184 10 1 5.513,2.695 5.940,2.844 0.427,0.149 10 VN2+ 5.513,3.448 5.940,3.597 0.427,0.149 10 VN2- 3.031,4.188 3.803,4.344 0.772,0.156 10 *1: for LHD 3.031,4.426 3.803,4.582 0.772,0.156 10 *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0046, P0047, P0048, P004B, P004C OR P004D)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
P0046, P0047, P0048, P004B, P004C or P004D is output A
P0046, P0047, P0048, P004B, P004C or P004D and other DTCs are output B

HINT:

If codes other than P0046, P0047, P0048, P004B, P004C or P004D are output, perform troubleshooting for those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (OPERATE TURBOCHARGER SUB-ASSEMBLY)

B

2.PERFORM ACTIVE TEST USING GTS (OPERATE TURBOCHARGER SUB-ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Engine and ECT / Active Test / Test the Turbo Charger Step Motor (Test the Turbo Charger Step Motor #2) / Data List / Target VN Turbo Position (Target VN Turbo Position #2) and Actual VN Turbo Position (Actual VN Turbo Position #2).


e.

While changing the Active Test value to 20, 95, 60 and 20%, check that Actual VN Turbo Position (Actual VN Turbo Position #2) smoothly changes to the set opening amount.

NOTICE:

When moving the vanes toward the fully closed position, make sure that Actual VN Turbo Position (Actual VN Turbo Position #2) does not become 5% or less.


OK:

The Actual VN Turbo Position (Actual VN Turbo Position #2) value follows the Target VN Turbo Position (Target VN Turbo Position #2).




OK

NG

3.INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR RESISTANCE)
3.INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR RESISTANCE)
a.
C217215E05
0.12,0.111 0.297,0.288 0.177,0.177 10 *a

Disconnect the DC motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (M-) - 2 (M+) Always 1 to 100 Ω
1 (M2-) - 2 (M2+) Always 1 to 100 Ω


Text in Illustration
*a Component without harness connected
(DC Motor)



OK

4.CHECK HARNESS AND CONNECTOR (DC MOTOR - ECM)

NG

6.REPLACE TURBOCHARGER SUB-ASSEMBLY
4.CHECK HARNESS AND CONNECTOR (DC MOTOR - ECM)
a.

Disconnect the DC motor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C90-2 (M+) - C45-86 (M+) Always Below 1 Ω
C90-1 (M-) - C45-85 (M-) Always Below 1 Ω
z67-2 (M2+) - C45-18 (VN2+) Always Below 1 Ω
z67-1 (M2-) - C45-41 (VN2-) Always Below 1 Ω
C90-2 (M+) or C45-86 (M+) - Body ground Always 10 kΩ or higher
C90-1 (M-) or C45-85 (M-) - Body ground Always 10 kΩ or higher
z67-2 (M2+) or C45-18 (VN2+) - Body ground Always 10 kΩ or higher
z67-1 (M2-) or C45-41 (VN2-) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C90-2 (M+) - C46-86 (M+) Always Below 1 Ω
C90-1 (M-) - C46-85 (M-) Always Below 1 Ω
z67-2 (M2+) - C46-18 (VN2+) Always Below 1 Ω
z67-1 (M2-) - C46-41 (VN2-) Always Below 1 Ω
C90-2 (M+) or C46-86 (M+) - Body ground Always 10 kΩ or higher
C90-1 (M-) or C46-85 (M-) - Body ground Always 10 kΩ or higher
z67-2 (M2+) or C46-18 (VN2+) - Body ground Always 10 kΩ or higher
z67-1 (M2-) or C46-41 (VN2-) - Body ground Always 10 kΩ or higher



d.

Reconnect the DC motor connector.


e.

Reconnect the ECM connector.



OK

5.REPLACE ECM

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE ECM

NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE TURBOCHARGER SUB-ASSEMBLY

When DTC P0046, P0047 or P0048 is output:

·

Replace the turbocharger sub-assembly (for bank 1) (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>REMOVAL).


When DTC P004B, P004C or P004D is output:

·

Replace the turbocharger sub-assembly (for bank 2) (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>REMOVAL).



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Turn the ignition switch to ON for 5 seconds or more.


e.

2 seconds after the engine is started, race the engine for 1 second.


f.

Enter the following menus: Engine and ECT / Trouble Codes.


g.

Confirm that the DTC is not output again.



NEXT

END