Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) M

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  REGISTRATION  


PROCEDURE

Hide 1. REGISTRATION

NOTICE:
·

When a fuel injector is replaced, the new fuel injector compensation code must be input into the ECM. When the ECM is replaced, all of the existing fuel injector compensation codes must be input into the new ECM.

·

Fuel injector compensation codes are unique, 30 digit, alphanumeric values printed on the head portion of each fuel injector. If an incorrect fuel injector compensation code is input into the ECM, the engine assembly may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.



A141119E08
2.896,1.917 3.135,2.771 3.135,2.771 2.948,2.771 false 0.083,0.021 0.781,0.25 0.698,0.229 10 false Example: 1.198,2.688 3.031,2.875 1.833,0.188 10 false Injector Compensation Code

a.

After replacing fuel injector(s) with new one(s), input compensation code(s) of fuel injector(s) into ECM as follows:

HINT:
·

Each fuel injector has different fuel injection characteristics. In order to optimize the fuel injections, the ECM uses the compensation codes to balance the different fuel injections between each fuel injector.

·

When you first turn the ignition switch to ON after replacing the ECM or a fuel injector(s), DTC P1601 is set. This is to inform you that registration of a fuel injector compensation code(s) is/are required. Manually clear the DTC upon completion of the compensation code registration.



i.

Input the compensation code(s), which is/are imprinted on the head portion(s) of the new fuel injector(s), into the intelligent tester.


ii.

Input the new compensation code(s) into the ECM using the tester.


iii.

Turn the tester off and turn the ignition switch off.


iv.

Wait for at least 30 seconds.


v.

Turn the ignition switch to ON and turn the tester on.


vi.

Clear DTC P1601 stored in the ECM using the tester (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DTC CHECK / CLEAR).



b.

Register compensation code.

A169590E07
2.333,1.177 2.885,1.354 0.552,0.177 10 false START 0.094,0.094 4.729,0.531 4.635,0.438 10 false How to Register Fuel Injector Compensation Codes Using Intelligent Tester: (Conduct prior to replacing fuel injector) 4.042,1.083 6.938,1.469 2.896,0.385 10 false *1: When registering compensation codes by manual input (Fuel injector replacement, etc.) 4.042,2 6.646,2.521 2.604,0.521 10 false *2: When registering compensation codes that are already stored in intelligent tester (ECM replacement, etc.) 2.042,1.875 3.104,2.063 1.063,0.188 10 false Select Function 1.802,2.573 3.375,2.76 1.573,0.188 10 false Select Cylinder Number 1.719,3.271 4.344,3.448 2.625,0.177 10 false Option Dialog: Select Input*1 or Open*2 2.729,3.823 3.552,4.01 0.823,0.188 10 false Select Input 5.479,3.833 6.302,4.021 0.823,0.188 10 false Select Open 1.563,4.292 3.854,4.469 2.292,0.177 10 false Input Compensation Code Manually 4.365,4.281 6.719,4.469 2.354,0.188 10 false Retrieve Saved Compensation Code 4.479,4.948 5.01,5.135 0.531,0.188 10 false Normal 5.688,4.948 6.417,5.115 0.729,0.167 10 false Abnormal 5.115,5.563 6.083,5.75 0.969,0.188 10 false Retrieval Error 4.188,6.021 7.104,6.375 2.917,0.354 10 false Go back to option dialog to select input, due to compensation code not being stored in tester 1.646,5.594 3.51,5.76 1.865,0.167 10 false Confirm Compensation Code 1.646,6.417 3.51,6.583 1.865,0.167 10 false Register Compensation Code 5.396,6.885 6.583,7.063 1.188,0.177 10 false Registration Error 1.635,7.094 3.969,7.271 2.333,0.177 10 false Option Dialog: Continue Registration 2.76,7.542 5.26,7.75 2.5,0.208 10 false Finish compensation code registration 2.417,8.021 2.771,8.24 0.354,0.219 10 false END 0.24,7.281 1.25,7.823 1.01,0.542 10 false Continue with registration for other cylinders

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



iii.

Turn the tester on.


iv.
G036522

Enter the following menus: Powertrain / Engine / Utility / Injector Compensation.


v.

Press Next.


vi.
G036523

Press Next again to proceed.


vii.
G036528

Select "Set Compensation Code".


viii.

Press Next.


ix.
A166685

Select the number of the cylinder corresponding to the fuel injector compensation code that you want to read.


x.

Press Next.


xi.
G036529

Register compensation code.

1.

Press Input.

2.
A168951

Manually input the cylinder compensation code using the keyboard on the tester screen. The code is a 30 digit, alphanumeric value printed on the injector head portion.

HINT:

Each fuel injector compensation code is unique. The compensation code for each selected cylinder must be input into the tester correctly.


3.

Confirm that the compensation code for the selected cylinder is correct, and then press OK.



xii.
G036531

Check that the compensation code displayed on the screen is correct by comparing it with the 30 digit alphanumeric value on the head portion of the fuel injector.

NOTICE:

If an incorrect fuel injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.


HINT:
·

If a wrong compensation code is input or read, return to the Input Value screen by pressing Input.

·

The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and repeat this operation.




xiii.

Press Next to register the compensation code in the ECM.

HINT:
·

If the registration process fails, the compensation code may be incorrect. Check the compensation code again.

·

If the input compensation code fails to register even though it is input correctly, there may be a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and restart this operation.




xiv.
G036532

If you want to continue with other compensation code registrations, press Next. To finish the registration, press Cancel.


xv.

Turn the ignition switch off and then turn the tester off.


xvi.

Wait for at least 30 seconds.


xvii.

Turn the ignition switch to ON and then turn the tester on.


xviii.

Clear DTC P1601 stored in the ECM using the tester (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DTC CHECK / CLEAR).



Hide 2. READING REGISTERED DATA

NOTICE:
·

When a fuel injector is replaced, the new fuel injector compensation code must be input into the ECM. When the ECM is changed, all of the existing fuel injector compensation codes must be input into the new ECM.

·

Fuel injector compensation codes are unique, 30 digit, alphanumeric values printed on the head portion of each fuel injector. If an incorrect fuel injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.



a.

When replacing ECM with a new one, input all fuel injector compensation codes into new ECM as follows:

HINT:
·

Each fuel injector has different fuel injection characteristics. In order to optimize the fuel injections, the ECM uses the compensation codes to balance the different fuel injections between each injector.

·

When you first turn the ignition switch to ON after replacing the ECM or a fuel injector(s), DTC P1601 is set. This is to inform you that registration of a fuel injector compensation codes(s) is/are required. Manually clear the DTC upon completion of the compensation code registration.



i.

Prior to replacing the ECM, read and save each fuel injector compensation code, stored in the original ECM, using the intelligent tester.


ii.

After installing a new ECM, input the saved compensation codes into the new ECM using the tester.


iii.

Turn the tester off and turn the ignition switch off.


iv.

Wait for at least 30 seconds.


v.

Turn the ignition switch to ON and turn the tester on.


vi.

Clear DTC P1601 stored in the ECM using the tester (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DTC CHECK / CLEAR).



b.

Read and save fuel injector compensation codes.

A169591E04
2.448,0.948 2.99,1.135 0.542,0.188 10 false START 0.229,0.063 4.833,0.448 4.604,0.385 10 false How to Read and Save Fuel Injector Compensation Codes Using Intelligent Tester: (Conduct prior to replacing ECM) 2.219,1.583 3.219,1.75 1,0.167 10 false Select Function 1.927,2.208 3.458,2.385 1.531,0.177 10 false Select Cylinder Number 2.51,2.823 2.917,2.99 0.406,0.167 10 false Read 1.396,3.594 4.042,3.781 2.646,0.188 10 false Display Compensation Code to be Saved 5.146,3.594 5.896,3.771 0.75,0.177 10 false Read Error 2.74,4.229 4.5,4.604 1.76,0.375 10 false If compensation codes are not already stored in tester 5.125,4.177 6.781,4.552 1.656,0.375 10 false If compensation codes are already stored in tester 2.135,5.115 3.198,5.302 1.063,0.188 10 false Confirm to Save 4.708,5.115 6.073,5.302 1.365,0.188 10 false Confirm to Overwrite 2.521,5.938 2.917,6.125 0.396,0.188 10 false Save 1.896,6.646 3.625,7 1.729,0.354 10 false Option Dialog: Continue Reading/Saving Operation 5.198,6.979 5.969,7.156 0.771,0.177 10 false Save Error 2.813,7.479 5.75,7.688 2.938,0.208 10 false Finish reading and saving compensation codes 0.073,6.927 1.438,7.302 1.365,0.375 10 false Read and save other compensation codes 2.51,7.969 2.885,8.135 0.375,0.167 10 false END 1.615,8.365 3.813,8.563 2.198,0.198 10 false Proceed to Registration Procedure

HINT:

The following operation is available with ECMs that can transmit the registered fuel injector compensation codes to the intelligent tester.


i.
A141119E08
2.896,1.917 3.135,2.771 3.135,2.771 2.948,2.771 false 0.083,0.021 0.781,0.25 0.698,0.229 10 false Example: 1.198,2.688 3.031,2.875 1.833,0.188 10 false Injector Compensation Code

Connect the intelligent tester to the DLC3.


ii.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



iii.

Turn the tester on.


iv.
G036522

Enter the following menus: Powertrain / Engine / Utility / Injector Compensation.


v.

Press Next.


vi.
G036523

Press Next again to proceed.


vii.
G036524

Select Read Compensation Code.


viii.

Press Next.


ix.
A166685

Select the number of the cylinder corresponding to the fuel injector compensation code that you want to read.


x.

Press Next.

HINT:

The reading process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found, the ECM may be malfunctioning. Check the ECM and restart this operation.



xi.
G036526

Check the fuel injector compensation code (30 digit alphanumeric value) displayed on the tester screen.


xii.

Press Save.


xiii.

Check that the compensation code displayed on the tester screen is correct.

A385043E01
0.688,0.115 3.26,0.49 2.573,0.375 10 false When no fuel injector compensation code for the cylinder exists in the tester: 4.052,0.125 6.625,0.5 2.573,0.375 10 false When another fuel injector compensation code for the cylinder exists in the tester:


xiv.

Press Save or Replace to save the fuel injector compensation code.

HINT:
·

The existing compensation code is overwritten with the new compensation code and is deleted from the tester.

·

The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and restart this operation.




xv.
G036526

If you want to read and save other fuel injector compensation codes for other cylinders, press Next to continue. To finish this operation, press Cancel.


xvi.

Turn the ignition switch off.


xvii.

Turn the tester off.


xviii.

Replace the ECM.


xix.
A141119E08
2.896,1.917 3.135,2.771 3.135,2.771 2.948,2.771 false 0.083,0.021 0.781,0.25 0.698,0.229 10 false Example: 1.198,2.688 3.031,2.875 1.833,0.188 10 false Injector Compensation Code

Connect the intelligent tester to the DLC3.


xx.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



xxi.

Turn the tester on.


xxii.
G036522

Enter the following menus: Powertrain / Engine / Utility / Injector Compensation.


xxiii.

Press Next.


xxiv.
G036523

Press Next again to proceed.


xxv.
G036528

Select Set Compensation Code.


xxvi.

Press Next.


xxvii.
A166685

Select the number of the cylinder corresponding to the fuel injector compensation code that you want to read.


xxviii.

Press Next.


xxix.
G036531

Check that the compensation code displayed on the screen is correct by comparing it with the 30 digit alphanumeric value on the head portion of the fuel injector.

NOTICE:

If an incorrect fuel injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.


HINT:
·

If a wrong compensation code is input or read, return to the Input Value screen by pressing input.

·

The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and repeat this operation.




xxx.

Press Next to register the compensation code in the ECM.

HINT:
·

If the registration process fails, the compensation code may be incorrect. Check the compensation code again.

·

If the input compensation code fails to register even though it is input correctly, there may be a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and restart this operation.




xxxi.
G036532

If you want to continue with other compensation code registrations, press Next. To finish the registration, press Cancel.


xxxii.

Turn the ignition switch off and then turn the tester off.


xxxiii.

Wait for at least 30 seconds.


xxxiv.

Turn the ignition switch to ON and then turn the tester on.


xxxv.

Clear DTC P1601 stored in the ECM using the tester (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DTC CHECK / CLEAR).