The variable nozzle vane type turbocharger consists primarily of a compressor wheel, turbine wheel, nozzle vane, unison ring, DC motor and nozzle vane position sensor.
The nozzle vane position sensor consists of a Hall IC and a magnetic yoke that rotates in unison with the movement of the linkage that actuates the nozzle vane. The nozzle vane position sensor converts the changes in the magnetic flux that are caused by the rotation of the DC motor (hence, the rotation of the magnetic yoke) into electric signals, and outputs them to the ECM. The ECM determines the actual nozzle vane position from the electric signals in order to calculate the target nozzle vane position.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Ignition switch ON for 1 second | VNA or VNA2 voltage is 0.1 V or less for 2.1 seconds (1 trip detection logic). | ·
Nozzle vane position sensor (turbocharger sub-assembly) ·
Open or short in nozzle vane position sensor circuit ·
ECM |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Ignition switch ON for 1 second | VNA or VNA2 voltage is 4.9 V or higher for 2.1 seconds (1 trip detection logic). | ·
Nozzle vane position sensor (turbocharger sub-assembly) ·
Open or short in nozzle vane position sensor circuit ·
ECM |
If DTC P2564, P2565, P2588 and/or P2589 is stored due to the nozzle vane being stuck open, the following symptoms may appear:
- Lack of power
- Vehicle surge or hesitation under light or medium load
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P2564 P2565, P2588 or P2589 is output | A |
| P2564 P2565, P2588 or P2589 and other DTCs are output | B |
A
B
(See pageEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DIAGNOSTIC TROUBLE CODE CHART)
Disconnect the nozzle vane position sensor connector.
Disconnect the ECM.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C89-3 (VNVC) - C45-120 (VNVC) | Always | Below 1 Ω |
| C89-2 (VNE2) - C45-97 (VNE2) | Always | Below 1 Ω |
| C89-1 (VTA1) - C45-74 (VNA) | Always | Below 1 Ω |
| z66-3 (VNC2) - C45-120 (VNVC) | Always | Below 1 Ω |
| z66-2 (VE2) - C45-97 (VNE2) | Always | Below 1 Ω |
| z66-1 (VTI2) - C45-117 (VNA2) | Always | Below 1 Ω |
| C89-3 (VNVC) or C45-120 (VNVC) - Body ground | Always | 10 kΩ or higher |
| C89-1 (VTA1) or C45-74 (VNA) - Body ground | Always | 10 kΩ or higher |
| z66-3 (VNC2) or C45-120 (VNVC) - Body ground | Always | 10 kΩ or higher |
| z66-1 (VTI2) or C45-117 (VNA2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C89-3 (VNVC) - C46-120 (VNVC) | Always | Below 1 Ω |
| C89-2 (VNE2) - C46-97 (VNE2) | Always | Below 1 Ω |
| C89-1 (VTA1) - C46-74 (VNA) | Always | Below 1 Ω |
| z66-3 (VNC2) - C46-120 (VNVC) | Always | Below 1 Ω |
| z66-2 (VE2) - C46-97 (VNE2) | Always | Below 1 Ω |
| z66-1 (VTI2) - C46-117 (VNA2) | Always | Below 1 Ω |
| C89-3 (VNVC) or C46-120 (VNVC) - Body ground | Always | 10 kΩ or higher |
| C89-1 (VTA1) or C46-74 (VNA) - Body ground | Always | 10 kΩ or higher |
| z66-3 (VNC2) or C46-120 (VNVC) - Body ground | Always | 10 kΩ or higher |
| z66-1 (VTI2) or C46-117 (VNA2) - Body ground | Always | 10 kΩ or higher |
Reconnect the nozzle vane position sensor connector.
Reconnect the ECM connector.
OK
NG
Disconnect the nozzle vane position sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C89-3 (VNVC) - C89-2 (VNE2) | Ignition switch ON | 4.5 to 5.5 V |
| z66-3 (VNC2) - z66-2 (VE2) | Ignition switch ON | 4.5 to 5.5 V |
| *A | for Bank 1 |
| *B | for Bank 2 |
| *a | Front view of wire harness connector
(to Nozzle Vane Position Sensor) |
OK
NG
When DTC P2564 or P2565 is output:
Replace the turbocharger sub-assembly (for bank 1) (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>REMOVAL).
When DTC P2588 or P2589 is output:
Replace the turbocharger sub-assembly (for bank 2) (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>REMOVAL).
NEXT
Replace the ECM (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Repair or replace the harness or connector.
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DTC CHECK / CLEAR).
Turn the ignition switch off and leave the vehicle for 15 seconds.
Turn the ignition switch to ON for 1 second.
Confirm that the DTC is not output again.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Engine and ECT / Utility / All Readiness.
Input DTC P2564 P2565, P2588 or P2589.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, idle the engine.
NEXT