Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › RELAY › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254997 RELAY G

1VD-FTV ENGINE CONTROL  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT FUEL PUMP RELAY (SUB PUMP)

a.
A184106E08
2.542,1.115 2.938,1.115 false 2.542,1.615 2.948,1.615 false 1.573,0.177 1.698,0.177 1.698,0.177 2.031,0.563 false 3.031,0.177 2.906,0.177 2.906,0.177 2.625,0.552 false 0.208,0.729 0.417,0.906 0.208,0.177 10 false 3 1.208,0.729 1.406,0.906 0.198,0.177 10 false 5 0.208,1.271 0.365,1.448 0.156,0.177 10 false 2 1.208,1.271 1.438,1.448 0.229,0.177 10 false 1 3.021,1.521 3.229,1.698 0.208,0.177 10 false 3 3,1.021 3.198,1.198 0.198,0.177 10 false 5 3.094,0.083 3.25,0.26 0.156,0.177 10 false 2 1.417,0.083 1.646,0.26 0.229,0.177 10 false 1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 2.INSPECT EDU RELAY (EDU1)

A184106E08
2.542,1.115 2.938,1.115 false 2.542,1.615 2.948,1.615 false 1.573,0.177 1.698,0.177 1.698,0.177 2.031,0.563 false 3.031,0.177 2.906,0.177 2.906,0.177 2.625,0.552 false 0.208,0.729 0.417,0.906 0.208,0.177 10 false 3 1.208,0.729 1.406,0.906 0.198,0.177 10 false 5 0.208,1.271 0.365,1.448 0.156,0.177 10 false 2 1.208,1.271 1.438,1.448 0.229,0.177 10 false 1 3.021,1.521 3.229,1.698 0.208,0.177 10 false 3 3,1.021 3.198,1.198 0.198,0.177 10 false 5 3.094,0.083 3.25,0.26 0.156,0.177 10 false 2 1.417,0.083 1.646,0.26 0.229,0.177 10 false 1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied between 1 and 2 10 kΩ or higher
Battery voltage is applied between 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 3.INSTALL EDU RELAY (EDU2)

A184106E08
2.542,1.115 2.938,1.115 false 2.542,1.615 2.948,1.615 false 1.573,0.177 1.698,0.177 1.698,0.177 2.031,0.563 false 3.031,0.177 2.906,0.177 2.906,0.177 2.625,0.552 false 0.208,0.729 0.417,0.906 0.208,0.177 10 false 3 1.208,0.729 1.406,0.906 0.198,0.177 10 false 5 0.208,1.271 0.365,1.448 0.156,0.177 10 false 2 1.208,1.271 1.438,1.448 0.229,0.177 10 false 1 3.021,1.521 3.229,1.698 0.208,0.177 10 false 3 3,1.021 3.198,1.198 0.198,0.177 10 false 5 3.094,0.083 3.25,0.26 0.156,0.177 10 false 2 1.417,0.083 1.646,0.26 0.229,0.177 10 false 1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied between 1 and 2 10 kΩ or higher
Battery voltage is applied between 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 4.INSPECT AIR FUEL RATIO SENSOR RELAY (A/F) (w/ DPF)

A184106E08
2.542,1.115 2.938,1.115 false 2.542,1.615 2.948,1.615 false 1.573,0.177 1.698,0.177 1.698,0.177 2.031,0.563 false 3.031,0.177 2.906,0.177 2.906,0.177 2.625,0.552 false 0.208,0.729 0.417,0.906 0.208,0.177 10 false 3 1.208,0.729 1.406,0.906 0.198,0.177 10 false 5 0.208,1.271 0.365,1.448 0.156,0.177 10 false 2 1.208,1.271 1.438,1.448 0.229,0.177 10 false 1 3.021,1.521 3.229,1.698 0.208,0.177 10 false 3 3,1.021 3.198,1.198 0.198,0.177 10 false 5 3.094,0.083 3.25,0.26 0.156,0.177 10 false 2 1.417,0.083 1.646,0.26 0.229,0.177 10 false 1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied between 1 and 2 10 kΩ or higher
Battery voltage is applied between 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 5.INSPECT INTEGRATION RELAY (IG2)

a.

Measure the resistance of the IG2 MAIN fuse.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IG2 MAIN fuse Always Below 1 Ω


If the result is not as specified, replace the IG2 MAIN fuse.



b.
U151388E02
0.49,2.604 0.708,2.792 0.219,0.188 10 false 1C 1.396,2.615 1.615,2.823 0.219,0.208 10 false 1B 2.469,2.625 2.677,2.813 0.208,0.188 10 false 1A 0.167,0.167 2.646,0.552 2.479,0.385 10 false Component without harness connected: (Integration Relay)

Measure the resistance of the ignition relay No. 2 (IG2) circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1B-8 Battery voltage is not applied to terminals 1B-6 and 1B-7 10 kΩ or higher
Battery voltage is applied to terminals 1B-6 and 1B-7 Below 1 Ω


If the result is not as specified, replace the integration relay.



Hide 6.INSPECT INTEGRATION RELAY (EFI MAIN)

a.

Measure the resistance of the EFI MAIN fuse.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI MAIN fuse Always Below 1 Ω


If the result is not as specified, replace the EFI MAIN fuse.



b.
U151388E02
0.49,2.604 0.708,2.792 0.219,0.188 10 false 1C 1.396,2.615 1.615,2.823 0.219,0.208 10 false 1B 2.469,2.625 2.677,2.813 0.208,0.188 10 false 1A 0.167,0.167 2.646,0.552 2.479,0.385 10 false Component without harness connected: (Integration Relay)

Measure the resistance of the EFI MAIN relay circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1B-4 Battery voltage is not applied to terminals 1B-2 and 1B-3 10 kΩ or higher
Battery voltage is applied to terminals 1B-2 and 1B-3 Below 1 Ω


If the result is not as specified, replace the integration relay.



Hide 7.INSPECT INTEGRATION RELAY (EFI MAIN 2)

a.

Measure the resistance of the EFI MAIN 2 fuse.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI MAIN 2 fuse Always Below 1 Ω


If the result is not as specified, replace the EFI MAIN 2 fuse.



b.
U151388E02
0.49,2.604 0.708,2.792 0.219,0.188 10 false 1C 1.396,2.615 1.615,2.823 0.219,0.208 10 false 1B 2.469,2.625 2.677,2.813 0.208,0.188 10 false 1A 0.167,0.167 2.646,0.552 2.479,0.385 10 false Component without harness connected: (Integration Relay)

Measure the resistance of the EFI MAIN 2 relay circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1A-4 Battery voltage is not applied to terminals 1A-2 and 1A-3 10 kΩ or higher
Battery voltage is applied to terminals 1A-2 and 1A-3 Below 1 Ω


If the result is not as specified, replace the integration relay.



Hide 8.INSPECT MAIN BODY ECU (IG1 NO. 1)

a.

Measure the resistance according to the value(s) in the table below.

A385396E01
2.958,0.74 3.323,0.979 0.365,0.24 1.646,1.563 1.979,1.802 0.333,0.24 3.552,3.813 3.865,4.021 0.313,0.208 3.146,1.771 3.146,3.01 false 2.448,1.479 2.625,1.583 2.625,1.583 2.625,3.021 false 1.438,2.281 1.438,3.031 false 4.063,4.604 4.156,4.802 4.156,4.802 4.156,5.365 false 0.177,0.104 2.635,0.448 2.458,0.344 10 false Component without harness connected: (Main Body ECU) 3.063,0.781 3.375,0.979 0.313,0.198 10 false 2B 3.115,3.063 3.427,3.26 0.313,0.198 10 false 5 2.552,3.052 2.813,3.25 0.26,0.198 10 false 17 1.385,3.063 1.646,3.26 0.26,0.198 10 false 1 1.719,1.604 2.031,1.802 0.313,0.198 10 false 2A 3.625,3.833 3.938,4.031 0.313,0.198 10 false 2D 4.094,5.406 4.354,5.604 0.26,0.198 10 false 43

Standard Resistance:
Tester Connection Condition Specified Condition
2A1 - 2B17 Battery voltage is not applied to terminals 2B-5 and 2D-43 10 kΩ or higher
Battery voltage is applied to terminals 2B-5 and 2D-43 Below 1 Ω


If the result is not as specified, replace the cowl side junction block LH.


Hide 28300D 10.INSPECT STARTER CUT RELAY (ST CUT)

Hide 82733A 13.INSPECT MAIN BODY ECU (ACC RELAY)