Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0100  Mass Air Flow Circuit Malfunction  


DESCRIPTION

The mass air flow meter consists of a platinum hot wire, a temperature sensor and a control circuit installed in a plastic housing. The temperature sensor (located in the intake air by-pass of the housing) detects the intake air temperature.

There is little variation in the output from the mass air flow meter, as the output voltage is converted into a periodic signal which minimizes the effect of wire harness resistance.

The internal circuit of the mass air flow meter contains a hot wire and cold wire. A voltage is output through a bridge circuit (refer to the illustration) indicating the cooling of the hot wire according to the intake air amount. This voltage is then converted into a periodic signal by the periodic signal conversion circuit and output to the ECM. The frequency varies between approximately 250 to 11000 Hz depending on the air flow rate. The ECM calculates the mass air flow rate based on this frequency.

A207644E07
1.906,1.365 1.677,1.719 false 1.01,2.573 1.365,1.833 false 5.917,1.958 5.604,0.51 5.604,0.51 5.792,0.51 false 6.104,2.063 6.24,3.073 false 5.563,2.531 4.563,3.26 false 2.344,1.948 2.625,1.781 2.625,1.781 2.771,1.781 false 1.698,0.531 2,0.74 0.302,0.208 10 false +B 1.604,0.854 2.688,1.156 1.083,0.302 10 false Power Transistor 2.813,1.688 3.76,1.938 0.948,0.25 10 false Output Voltage 1.927,1.208 3.042,1.427 1.115,0.219 10 false Hot Wire Element 0.156,2.604 1.375,2.875 1.219,0.271 10 false Cold Wire Element 5.823,0.427 6.938,0.646 1.115,0.219 10 false Hot Wire Element 5.938,3.104 7.135,3.375 1.198,0.271 10 false Cold Wire Element 3.76,3.281 5.875,3.646 2.115,0.365 10 false Temperature Sensor (Thermistor) 2.177,2.323 3.375,2.646 1.198,0.323 10 false Periodic Signal Conversion Circuit 2.188,3.302 3.396,3.521 1.208,0.219 10 false Output Frequency

P0100
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
3 seconds after engine is started Mass air flow meter signal frequency is less than 850 Hz with the engine speed at 400 rpm or more for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM



Related Data List
DTC No. Data List
P0100 MAF

HINT:

If DTC P0100 is stored, the following symptoms may appear (as the ECM mistakenly determines that there is less air than the actual intake air amount, EGR is decreased according to the target EGR):

-

Combustion noise worsens




WIRING DIAGRAM

A275248E01
3.309,2.02 4.696,2.176 1.387,0.156 10 Mass Air Flow Meter 3.071,1.792 3.366,1.975 0.295,0.184 10 C50 5.097,2.805 5.401,3.003 0.304,0.198 10 A38 5.424,2.801 5.728,2.998 0.304,0.198 10 A52 5.079,2.623 5.395,2.779 0.316,0.156 10 44*1 5.392,2.623 5.708,2.779 0.316,0.156 10 44*2 5.088,1.014 5.392,1.212 0.304,0.198 10 C45 5.415,1.01 5.719,1.207 0.304,0.198 10 C46 5.081,1.528 5.386,1.726 0.304,0.198 10 C45 5.408,1.523 5.712,1.721 0.304,0.198 10 C46 5.098,0.848 5.413,1.004 0.316,0.156 10 71*1 5.411,0.848 5.726,1.004 0.316,0.156 10 71*2 5.074,1.357 5.390,1.513 0.316,0.156 10 94*1 5.387,1.357 5.703,1.513 0.316,0.156 10 94*2 5.838,0.928 6.091,1.090 0.253,0.163 10 VG 5.796,1.428 6.174,1.591 0.378,0.163 10 EVG 5.78,2.688 6.189,2.850 0.408,0.163 10 MREL 4.372,0.877 4.625,1.040 0.253,0.163 10 FG 4.295,1.427 4.643,1.590 0.348,0.163 10 E2G 3.459,0.577 3.707,0.766 0.248,0.188 10 +B 3.29,0.591 3.400,0.738 0.110,0.147 10 3 4.687,0.9 4.796,1.046 0.110,0.147 10 1 4.687,1.437 4.796,1.583 0.110,0.147 10 2 2.043,0.703 2.259,0.878 0.215,0.175 10 1A 2.043,1.054 2.259,1.229 0.215,0.175 10 1A 0.897,2.03 1.112,2.205 0.215,0.175 10 1A 0.278,2.044 0.494,2.219 0.215,0.175 10 1C 1.175,2.034 1.284,2.181 0.110,0.147 10 3 0.115,2.032 0.224,2.179 0.110,0.147 10 1 2.09,1.25 2.200,1.396 0.110,0.147 10 2 2.09,0.531 2.200,0.677 0.110,0.147 10 4 0.404,0.829 1.171,1.004 0.767,0.174 10 EFI MAIN 2 1.161,1.409 1.928,1.583 0.767,0.174 10 EFI MAIN 2 2.566,0.862 3.235,1.033 0.669,0.171 10 EFI NO. 2 1.072,2.259 2.212,2.412 1.140,0.154 10 Integration Relay 0.624,2.968 1.085,3.138 0.461,0.170 10 Battery 3.314,3.038 4.125,3.201 0.811,0.163 10 *1: for LHD 3.314,3.372 4.125,3.535 0.811,0.163 10 *2: for RHD 6.186,3.342 6.569,3.530 0.383,0.188 10 ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT MASS AIR FLOW METER (POWER SOURCE CIRCUIT)
U162827E01
1.281,1.677 1.511,1.868 0.229,0.191 10 +B 0.191,0.183 0.386,0.378 0.195,0.195 10 *a 1.699,1.115 1.415,1.677 false 0.322,0.993 0.619,1.139 0.297,0.146 10 C50

a.

Disconnect the mass air flow meter connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C50-3 (+B) - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Mass Air Flow Meter)


c.

Reconnect the mass air flow meter connector.



OK

2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - INTEGRATION RELAY)
2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C50-1 (FG) - C45-71 (VG) Always Below 1 Ω
C50-2 (E2G) - C45-94 (EVG) Always Below 1 Ω
C50-1 (FG) or C45-71 (VG) - Body ground Always 10 kΩ or higher


Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C50-1 (FG) - C46-71 (VG) Always Below 1 Ω
C50-2 (E2G) - C46-94 (EVG) Always Below 1 Ω
C50-1 (FG) or C46-71 (VG) - Body ground Always 10 kΩ or higher



d.

Reconnect the mass air flow meter connector.


e.

Reconnect the ECM connector.



OK

9.REPLACE MASS AIR FLOW METER

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - INTEGRATION RELAY)
a.

Disconnect the mass air flow meter connector.


b.

Remove the integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C50-3 (+B) - 1A-4 Always Below 1 Ω
C50-3 (+B) or 1A-4 - Body ground Always 10 kΩ or higher




OK

4.INSPECT INTEGRATION RELAY (EFI MAIN 2)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.INSPECT INTEGRATION RELAY (EFI MAIN 2)
a.

Inspect the integration relay (EFI MAIN 2) (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

5.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM)

NG

8.REPLACE INTEGRATION RELAY
5.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM)
a.

Remove the integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
1A-2 - A38-44 (MREL) Always Below 1 Ω
1A-2 or A38-44 (MREL) - Body ground Always 10 kΩ or higher


Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
1A-2 - A52-44 (MREL) Always Below 1 Ω
1A-2 or A52-44 (MREL) - Body ground Always 10 kΩ or higher




OK

6.CHECK ECM POWER SOURCE CIRCUIT

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK ECM POWER SOURCE CIRCUIT

NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPLACE INTEGRATION RELAY
a.

Replace the integration relay (EFI MAIN 2).



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPLACE MASS AIR FLOW METER

NEXT

10.CHECK WHETHER DTC OUTPUT RECURS
10.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.



c.

Start the engine and wait for 3 seconds or more.


d.

Enter the following menus: Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
P0100 is output A
No DTC is output B



A

11.REPLACE ECM

B

END

11.REPLACE ECM

NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Start the engine and wait for 3 seconds or more.


d.

Enter the following menus: Engine and ECT / Trouble Codes.


e.

Confirm that the DTC is not output again.



NEXT

END