Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0500  Vehicle Speed Sensor "A"  


DESCRIPTION

Vehicles, which are equipped with ABS (Anti-lock Brake System), detect the vehicle speed using the skid control ECU (brake actuator assembly) and speed sensor. The speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter assembly. The ECM determines the vehicle speed based on the frequency of the pulse signal.

A115899E87
0.333,1.083 1.552,1.5 1.219,0.417 10 false from Wheel Speed Sensor 1.813,1.958 3.313,2.229 1.5,0.271 10 false Skid Control ECU 3.521,1.958 5.49,2.177 1.969,0.219 10 false Combination Meter Assembly 2.844,0.531 3.76,0.719 0.917,0.188 10 false Pulse Signal 4.948,0.521 5.844,0.729 0.896,0.208 10 false Pulse Signal 6.042,1.323 6.531,1.604 0.49,0.281 10 false ECM

DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Drive the vehicle at 10 km/h (6.3 mph) or more While vehicle being driven, no vehicle speed sensor signal transmitted to ECM (2 trip detection logic).
·

Open or short in speedometer circuit

·

Speedometer assembly

·

ECM



Related Data List
DTC No. Data List
P0500 Vehicle Speed

WIRING DIAGRAM

A160610E36
0.202,1.804 1.676,1.945 1.474,0.141 10 from Speed Sensor 2.181,1.903 2.356,2.068 0.176,0.165 10 5 3.915,1.903 4.100,2.068 0.185,0.165 10 6 2.419,1.903 2.616,2.068 0.196,0.165 10 SI 5.017,1.903 5.129,2.068 0.112,0.165 10 8 5.968,1.38 6.256,1.545 0.288,0.165 10 5 V 5.202,1.943 5.543,2.108 0.341,0.165 10 SPD 5.669,2.799 6.022,2.964 0.353,0.165 10 ECM 2.362,2.611 2.712,2.776 0.350,0.165 10 E119 2.362,2.76 4.260,2.925 1.898,0.165 10 Combination Meter Assembly 5.383,2.576 6.520,2.797 1.137,0.221 10 A38*1, A52*2 4.052,3.162 4.798,3.325 0.746,0.163 10 *1: for LHD 4.052,3.435 4.798,3.598 0.746,0.163 10 *2: for RHD 3.645,1.903 3.841,2.068 0.196,0.165 10 +S

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OPERATION OF SPEEDOMETER
a.

Drive the vehicle and check whether the operation of the speedometer in the combination meter assembly is normal.

HINT:

The vehicle speed sensor is operating normally if the speedometer reading is normal.


OK:

The vehicle speed sensor is operating normally.




OK

2.READ VALUE USING GTS (VEHICLE SPEED)

NG

7.CHECK SPEEDOMETER CIRCUIT
2.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Engine and ECT / Data List / All Data / Vehicle Speed.


e.

Drive the vehicle.


f.

Read the value displayed on the GTS.

OK:

Vehicle speed displayed on GTS and speedometer display are equal.




OK

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

3.CHECK HARNESS AND CONNECTOR
3.CHECK HARNESS AND CONNECTOR
U165250E01
1.466,0.429 1.872,0.611 0.406,0.181 10 E119 0.692,1.89 1.032,2.072 0.340,0.181 10 +S 0.083,0 0.297,0.217 0.214,0.217 10 *a 1.166,1.352 0.874,1.881 false

a.

Disconnect the combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E119-6 (+S) - Body ground Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)


c.

Reconnect the combination meter assembly connector.



OK

4.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)

NG

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
4.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)
U163454E02
2.135,1.344 2.25,2.125 false 2.24,2.167 2.688,2.375 0.448,0.208 10 false 6 (+S) 1.5,0.594 1.875,0.771 0.375,0.177 10 false E119 0.188,0.125 0.427,0.323 0.24,0.198 10 false *a 1.729,4.229 2.5,4.427 0.771,0.198 10 false Turn Wheel 0.313,4.104 0.615,4.271 0.302,0.167 10 false 0 V 0.052,2.667 0.688,2.833 0.635,0.167 10 false 5 to 12 V

a.

Move the shift lever to neutral.


b.

Jack up the vehicle.


c.

Check the voltage between the terminal of the combination meter assembly and the body ground while a wheel is turned slowly.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E119-6 (+S) - Body ground Ignition switch ON Voltage generated intermittently


Text in Illustration
*a Component with harness connected
(Combination Meter Assembly)

HINT:

The output voltage should fluctuate up and down, similarly to the diagram when the wheel is turned slowly.




OK

6.REPLACE ECM

NG

8.REPLACE COMBINATION METER ASSEMBLY
5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
E119-6 (+S) - A38-8 (SPD) Always Below 1 Ω
E119-6 (+S) or A38-8 (SPD) - Body ground Always 10 kΩ or higher


Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
E119-6 (+S) - A52-8 (SPD) Always Below 1 Ω
E119-6 (+S) or A52-8 (SPD) - Body ground Always 10 kΩ or higher



d.

Reconnect the combination meter assembly connector.


e.

Reconnect the ECM connector.



OK

6.REPLACE ECM

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.REPLACE ECM

NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CHECK SPEEDOMETER CIRCUIT
a.

Check the speedometer circuit (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speedometer Malfunction).

HINT:

Inspect the brake actuator assembly and speed sensor.




NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPLACE COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at 10 km/h (6.3 mph) or more.


f.

Enter the following menus: Engine and ECT / Trouble Codes.


g.

Confirm that the pending DTC is not output again.



NEXT

END