Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate that the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the GTS, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.



P0504
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Depress and release brake pedal with ignition switch ON Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch ON.
(b) Brake pedal is released.
(c) The STP signal is off when the ST1- signal is off, or the STP signal is on when the ST1- signal is on.
·

Open or short in stop light switch signal circuit

·

STOP fuse

·

IGN fuse

·

Stop light switch

·

ECM



Related Data List
DTC No. Data List
P0504 Stop Light Switch

WIRING DIAGRAM

A371200E02
0.727,1.562 3.220,1.769 2.493,0.206 10 from Integration Relay 1.232,0.542 2.113,0.748 0.881,0.206 10 from Battery 2.719,0.414 2.851,0.567 0.132,0.153 10 1 3.385,0.672 3.517,0.825 0.132,0.153 10 1 5.633,2.652 6.582,2.806 0.948,0.153 10 A38*1, A52*2 5.864,2.815 6.247,2.969 0.383,0.153 10 ECM 2.965,0.414 3.098,0.567 0.132,0.153 10 2 4.527,0.672 4.659,0.825 0.132,0.153 10 2 4.52,1.657 4.652,1.810 0.132,0.153 10 4 5.29,1.657 5.485,1.810 0.195,0.153 10 35 5.29,0.664 5.485,0.817 0.195,0.153 10 13 5.543,1.461 5.891,1.614 0.348,0.153 10 ST1- 5.543,0.459 5.891,0.613 0.348,0.153 10 STP 3.401,1.657 3.534,1.810 0.132,0.153 10 5 2.704,0.713 3.114,0.869 0.411,0.156 10 STOP 0.656,2.945 1.402,3.101 0.746,0.156 10 *1: for LHD 0.656,3.253 1.402,3.409 0.746,0.156 10 *2: for RHD 3.229,2.4 3.629,2.545 0.400,0.145 10 A73 3.229,2.561 5.396,2.748 2.167,0.187 10 Stop Light Switch Assembly 3.406,2.105 3.538,2.259 0.132,0.153 10 3 3.591,2.035 4.005,2.189 0.414,0.153 10 GND 3.581,1.566 3.764,1.779 0.183,0.213 10 B 4.319,0.567 4.502,0.780 0.183,0.213 10 L 3.572,0.567 3.755,0.780 0.183,0.213 10 B 4.319,1.557 4.502,1.770 0.183,0.213 10 L

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

Stop light switch conditions can be checked using the GTS.

(a)

Connect the GTS to the DLC3.

(b)

Turn the ignition switch to ON.

(c)

Turn the GTS on.

(d)

Enter the following menus: Engine and ECT / Data List / Stop Light Switch.

(e)

Check Stop Light Switch when the brake pedal is depressed and released.




Brake Pedal Operation Specified Condition
Depressed ON
Released OFF

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
a.
U163585E01
0.586,1.924 0.859,2.080 0.272,0.156 10 A73 0.181,0.158 0.336,0.314 0.154,0.156 10 *a 1.326,2.354 1.038,2.979 false 0.943,2.985 1.070,3.140 0.127,0.156 10 B

Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A73-1 - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STOP LIGHT SWITCH ASSEMBLY)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
a.
U163586E01
0.586,1.924 0.859,2.080 0.272,0.156 10 A73 0.181,0.158 0.336,0.314 0.154,0.156 10 *a 2.1,2.354 2.516,2.979 false 2.525,2.985 2.651,3.140 0.127,0.156 10 B

Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A73-5 - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY - STOP LIGHT SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A73-3 (GND) - Body ground Always Below 1 Ω




OK

4.CHECK ECM (STP AND ST1- VOLTAGE)

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK ECM (STP AND ST1- VOLTAGE)
U163703E02
1.771,3.667 2.146,4.292 false 1.781,3.365 2.531,2.719 false 0.521,0.333 0.719,0.531 0.198,0.198 10 false *a 2.208,0.333 2.406,0.531 0.198,0.198 10 false *b 1.573,2.229 1.771,2.427 0.198,0.198 10 false *c 0.24,3.073 0.594,3.26 0.354,0.188 10 false A38 2.604,2.604 3.229,2.771 0.625,0.167 10 false 13 (STP) 2.115,4.302 2.688,4.573 0.573,0.271 10 false 35 (ST1-) 0.26,3.823 0.583,4 0.323,0.177 10 false A52 0.323,3.323 0.521,3.521 0.198,0.198 10 false *A 0.344,4.104 0.542,4.302 0.198,0.198 10 false *B

a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Brake Pedal Condition Specified Condition
A38-35 (ST1-) - Body ground Released 11 to 14 V
Depressed 0 to 3 V
A38-13 (STP) - Body ground Released 0 to 3 V
Depressed 11 to 14 V


Standard Voltage:
for RHD
Tester Connection Brake Pedal Condition Specified Condition
A52-35 (ST1-) - Body ground Released 11 to 14 V
Depressed 0 to 3 V
A52-13 (STP) - Body ground Released 0 to 3 V
Depressed 11 to 14 V


Text in Illustration
*A for LHD
*B for RHD
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Front view of wire harness connector
(ECM)


d.

Reconnect the ECM connector.



NG

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)

OK

9.REPLACE ECM
5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A73-4 (L) - A38-35 (ST1-) Always Below 1 Ω
A73-2 (L) - A38-13 (STP) Always Below 1 Ω
A73-4 (L) or A38-35 (ST1-) - Body ground Always 10 kΩ or higher
A73-2 (L) or A38-13 (STP) - Body ground Always 10 kΩ or higher


Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
A73-4 (L) - A52-35 (ST1-) Always Below 1 Ω
A73-2 (L) - A52-13 (STP) Always Below 1 Ω
A73-4 (L) or A52-35 (ST1-) - Body ground Always 10 kΩ or higher
A73-2 (L) or A52-13 (STP) - Body ground Always 10 kΩ or higher




OK

6.REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.REPLACE STOP LIGHT SWITCH ASSEMBLY
a.

Replace the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STOP LIGHT SWITCH ASSEMBLY)

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY - STOP LIGHT SWITCH ASSEMBLY)

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPLACE ECM

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Depress and release the brake pedal.


f.

Enter the following menus: Engine and ECT / Trouble Codes.


g.

Confirm that the DTC is not output again.



NEXT

END