Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P2121  Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance  


DESCRIPTION

Refer to DTC P2120 (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P2120).

P2121
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG)
·

Accelerator pedal fully released for 3 seconds

·

Accelerator pedal depressed partway for 3 seconds

·

Accelerator pedal fully depressed for 3 seconds


The difference between VPA and VPA2 is less than 0.4 V, or more than 1.2 V for 0.5 seconds (1 trip detection logic).
·

Accelerator pedal position sensor circuit

·

Accelerator pedal position sensor

·

ECM



Related Data List
DTC No. Data List
P2121
·

Accel Position

·

Accel Sens. No.1 Volt %

·

Accel Sens. No.2 Volt %



CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (ACCELERATOR PEDAL POSITION SENSOR)

A

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)

B

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)

OK

3.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY
a.

Replace the accelerator pedal rod assembly (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL).



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch on (IG).


d.

Fully release the accelerator pedal for 3 seconds or more, then depress it partway for 3 seconds or more, and then fully depress it for 3 seconds or more.


e.

Enter the following menus: Engine and ECT / Trouble Codes.


f.

Read the DTCs.

Result
Result Proceed to
P2121 is output A
No DTC is output B



A

5.REPLACE ECM

B

END

5.REPLACE ECM

NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off.


d.

Turn the engine switch on (IG).


e.

Fully release the accelerator pedal for 3 seconds or more, then depress it partway for 3 seconds or more, and then fully depress it for 3 seconds or more.


f.

Enter the following menus: Engine and ECT / Trouble Codes.


g.

Confirm that the DTC is not output again.



NEXT

END