Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0299  Turbocharger / Supercharger Underboost  


DESCRIPTION

HINT:

Refer to DTC P0046 (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P0046).


P0299
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Accelerate vehicle with accelerator depressed halfway or more starting from a speed of 120 km/h (75 mph) or more for 2 minutes (make sure gear is fixed and does not change) The pressure is 55 kPa below the Target Booster Pressure for 40 seconds at an engine speed of 2800 to 4400 rpm (2 trip detection logic).
·

Turbocharger sub-assembly

·

Extremely low battery voltage (P0560 output simultaneously)

·

Disconnected pipe between turbocharger and intake manifold

·

Disconnected manifold absolute pressure sensor hose

·

Throttle valve stuck closed

·

EGR valve assembly does not close

·

Exhaust system or intake system modified (leading to increased pressure loss, etc.)

·

Manifold absolute pressure sensor

·

Injection system (reduction in fuel injection volume)

·

Fuel filter element sub-assembly clog

·

ECM



Related Data List
DTC No. Data List
P0299
·

Target Booster Pressure

·

MAP



HINT:

If DTC P0299 is stored due to the variable nozzle being stuck open, the following symptoms may appear:

-

Lack of power

-

Vehicle surge or hesitation under light or medium load




CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

Comparison of the data list items manifold absolute pressure and target booster pressure during acceleration under medium to high engine speeds can be used to determine the state of the problem.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0299)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
P0299 is output A
P0299 and other DTCs are output B



A

2.CHECK FREEZE FRAME DATA (COMMON RAIL PRESSURE AND TARGET COMMON RAIL PRESSURE)

B

2.CHECK FREEZE FRAME DATA (COMMON RAIL PRESSURE AND TARGET COMMON RAIL PRESSURE)
a.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


b.

Record the stored DTCs and freeze frame data.

Result
Result Proceed to
Difference between Common Rail Pressure and Target Common Rail Pressure of freeze frame data is 20000 kPa or more A
Except above B



B

A

GO TO INSPECT CLOGGED FUEL PIPE (LACK OF POWER OR HESITATION)