Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0627  Fuel Pump Control Circuit / Open  


DESCRIPTION

P0627
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Idling for 1 second Even though the CPU (command area inside the ECU) is outputting the suction control valve operation duty, the output monitor signal is absent for 0.5 seconds.
(1 trip detection logic)
·

Open or short in suction control valve circuit

·

Suction control valve (fuel supply pump assembly)

·

ECM



Related Data List
DTC No. Data List
P0627
·

Common Rail Pressure

·

Target Common Rail Pressure



HINT:
·

For more information on the fuel supply pump assembly (suction control valve) and common rail system, refer to System Description (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).

·

When DTC P0627 is stored, check the internal fuel pressure of the common rail by entering the following menus on the GTS: Engine and ECT / Data List / Common Rail Pressure.

Under a stable operating condition such as idling, Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure.



CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
a.
A164257E03
2.208,0.64 2.414,0.815 0.206,0.174 10 *2 0.053,0.042 0.259,0.205 0.206,0.162 10 *1 2.161,0.721 2.05,0.721 2.05,0.721 1.611,1.005 false

Disconnect the suction control valve connector.

Text in Illustration
*1 Fuel Supply Pump Assembly
*2 Suction Control Valve


b.

Measure the resistance of the suction control valve.

OK:

No open or short circuit malfunction.




OK

2.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)

NG

4.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
2.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
a.

Disconnect the suction control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
z64-1 (+B) - C45- 104 (PCV+) Always Below 1 Ω
z64-2 (PCV) - C45-105 (PCV-) Always Below 1 Ω
z64-1 (+B) or C45- 104 (PCV+) - Body ground Always 10 kΩ or higher
z64-2 (PCV) or C45-105 (PCV-) - Body ground Always 10 kΩ or higher


Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
z64-1 (+B) - C46- 104 (PCV+) Always Below 1 Ω
z64-2 (PCV) - C46-105 (PCV-) Always Below 1 Ω
z64-1 (+B) or C46- 104 (PCV+) - Body ground Always 10 kΩ or higher
z64-2 (PCV) or C46-105 (PCV-) - Body ground Always 10 kΩ or higher



d.

Reconnect the suction control valve connector.


e.

Reconnect the ECM connector.



OK

3.CHECK WHETHER DTC OUTPUT RECURS

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Start the engine and idle it for 1 second or more.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Read the DTCs.

Result
Result Proceed to
No DTC is output A
P0627 is output B



A

END

B

7.REPLACE ECM
4.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
a.

Replace the fuel supply pump assembly (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL).



NEXT

5.BLEED AIR FROM FUEL SYSTEM
5.BLEED AIR FROM FUEL SYSTEM

b.

Perform PM forced regeneration (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).

HINT:

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.




NEXT

6.PERFORM SUPPLY PUMP INITIALIZATION
6.PERFORM SUPPLY PUMP INITIALIZATION

NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPLACE ECM

NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off for 30 seconds or more.


d.

Start the engine and idle it for 1 second or more.


e.

Confirm that the DTC is not output again.



NEXT

END