Home › Engine / Hybrid System › 1VD-FTV (FUEL) › FUEL SUPPLY PUMP › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052783 1VD-FTV FUEL _0255110 FUEL SUPPLY PUMP A

1VD-FTV FUEL  FUEL SUPPLY PUMP  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail, cylinder head or intake manifold, it is necessary to replace the injection pipes with new ones.

·

w/ DPF:

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


a.

Disconnect the cables from the negative (-) main battery and sub-battery terminals.


Hide 25680 3.REMOVE EGR VALVE ASSEMBLY WITH EGR COOLER (w/ EGR System)

Hide 16331A 4.REMOVE THERMOSTAT

Hide 23920A 5.REMOVE FUEL COOLER ASSEMBLY (w/o DPF)

Hide 23901H 7.REMOVE FUEL TUBE SUB-ASSEMBLY (w/ DPF)

Hide 11336A 8.REMOVE TIMING GEAR COVER INSULATOR (w/ Intercooler)

Hide 11324 9.REMOVE TIMING CHAIN COVER PLATE

A174824

a.

Remove the 4 bolts, cover plate and gasket.


Hide 23811G 10.REMOVE NO. 1 FUEL PIPE

a.
A271224E02
0.125,0.083 0.333,0.25 0.208,0.167 10 false *A 0.125,2.552 0.333,2.719 0.208,0.167 10 false *B

Remove the union bolt, fuel pipe and 2 gaskets.

Text in Illustration
*A w/ DPF
*B w/o DPF


Hide 22100 11.REMOVE FUEL SUPPLY PUMP

a.
A185177

Using a wrench, hold the crankshaft.

NOTICE:

Do not turn the crankshaft counterclockwise.

If it is turned counterclockwise, check that the crankshaft pulley set bolt is not loose. If loose, tighten the bolt (See page Engine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>REASSEMBLY).


Torque:
108 N*m (1101 kgf*cm, 80 ft.*lbf)

or more



b.
A176402

Remove the set nut.


c.
A181384

Disconnect the fuel temperature sensor connector.


d.
A271225E02
0.063,0.052 0.292,0.281 0.229,0.229 10 true *A 0.063,2.604 0.323,2.854 0.26,0.25 10 true *B

Using a 6 mm hexagon wrench, remove the bolt.

Text in Illustration
*A w/ DPF
*B w/o DPF


e.

Loosen the 2 nuts.


f.
A181383E04
1.688,0.135 1.531,0.135 1.531,0.135 1.688,0.667 true 2.156,3.354 1.104,3.354 false 2,3.823 1.271,3.823 1.271,3.823 1.271,3.354 false 2.104,0.938 1.771,0.938 true 1.75,2.406 1.927,2.406 1.927,2.406 2.344,2.698 true 1.719,0.052 1.938,0.26 0.219,0.208 10 true *1 2.135,0.854 2.521,1.26 0.385,0.406 10 true SST 1.542,2.313 1.719,2.49 0.177,0.177 10 false *1 0.875,3.25 1.052,3.406 0.177,0.156 10 false *a

Disconnect the pump from the supply pump drive gear.

i.

Install SST (No. 1 adapter) to the timing chain cover.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05031, 09955-05010)

Text in Illustration
*1 SST (No. 1 adapter)
*a Service Hole

NOTICE:

Do not use any tools in this procedure.



ii.

Rotate the supply pump gear so that the service holes are aligned with SST (No. 1 adapter) as shown in the illustration.


iii.

Using SST, disconnect the pump from the supply pump drive gear.

NOTICE:
·

When removing or installing SST, do not push the supply pump gear.

·

Apply lubricant to the threads and tip of SST (center bolt) before using it.





g.

Remove the 2 nuts.

NOTICE:
·

Do not hold the supply pump by the parts indicated by the arrows in the illustration, as this may result in deformation, damage and fuel leakage.

·

The pump must be kept horizontal.

U163624E02
1.51,3.083 1.635,3.083 1.635,3.083 2.229,2.479 false 6.375,4.333 6.823,4.333 false 2.823,2.667 3.271,2.667 false 3.094,0.594 2.969,0.594 2.969,0.594 2.552,1.094 false 2.115,0.115 2,0.115 2,0.115 1.667,0.802 false 1.563,6.521 1.688,6.521 1.688,6.521 2.281,5.906 false 2.844,5.958 3.292,5.958 false 3.313,4.198 3.188,4.198 3.188,4.198 2.656,4.542 false 2.146,3.604 2.021,3.604 2.021,3.604 1.656,4.167 false 3.156,1.198 3.042,1.198 3.042,1.198 2.677,1.635 false 2.156,0.042 2.323,0.208 0.167,0.167 10 false *1 3.125,0.521 3.313,0.688 0.188,0.167 10 false *2 3.302,2.594 3.469,2.771 0.167,0.177 10 false *3 6.854,4.26 7.042,4.417 0.188,0.156 10 false *4 1.323,3 1.51,3.177 0.188,0.177 10 false *3 2.188,3.542 2.354,3.708 0.167,0.167 10 false *1 3.344,4.135 3.531,4.302 0.188,0.167 10 false *2 3.323,5.896 3.49,6.073 0.167,0.177 10 false *3 1.365,6.438 1.552,6.615 0.188,0.177 10 false *3 0.615,3.74 0.823,3.906 0.208,0.167 10 false *B 3.188,1.135 3.375,1.302 0.188,0.167 10 false *3 0.604,0.302 0.813,0.469 0.208,0.167 10 false *A



Text in Illustration
*A w/ DPF *B w/o DPF
*1 Fuel Temperature Sensor *2 Suction Control Valve
*3 Fuel Pipe *4 Drive Shaft


h.

Remove the O-ring from the supply pump.