| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Idling for 60 seconds | The actual fuel pressure exceeds the target fuel pressure by 5000 kPa or more for 30 seconds.
(1 trip detection logic) |
·
Short in suction control valve circuit ·
Suction control valve (fuel supply pump assembly) ·
Fuel pressure sensor (common rail assembly (for bank 1)) ·
ECM |
| DTC No. | Data List |
|---|---|
| P1229 | ·
Common Rail Pressure ·
Target Common Rail Pressure ·
Injection Pressure Correction ·
Target Pump SCV Current ·
Pump SCV Learning Value |
For more information on the fuel supply pump assembly (suction control valve) and common rail system, refer to System Description (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).
When DTC P1229 is stored, check the internal fuel pressure of the common rail assembly by entering the following menus: Engine and ECT / Data List / Common Rail Pressure, Target Common Rail Pressure.
Under a stable condition such as idling after warming up the engine, Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure when normal.
When there is a problem with the movement of the fuel supply pump assembly (when Common Rail Pressure is higher than Target Common Rail Pressure due to a problem in which the suction valve has difficulty closing), the values of Injection Pressure Correction and Target Pump SCV Current decrease.
The ECM stores this DTC if the actual fuel pressure inside the common rail remains higher than the target fuel pressure, despite the ECM closing the suction control valve. This DTC indicates that the suction control valve may be stuck open, or there may be a short in its circuit.
If this DTC is stored, the ECM enters fail-safe mode and limits the engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.
Refer to DTC P0088 (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P0088).
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
When this DTC is stored, be sure to carefully examine "Common Rail Pressure", "Target Common Rail Pressure", "Target Pump SCV Current", and "Pump SCV Learning Value" in the freeze frame data.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P1229 and "P0190, P0192 and/or P0193" are output | B |
| Except above | A |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Start the engine and warm it up.
Enter the following menus: Powertrain / Engine and ECT / Data List / Common Rail Pressure and Target Common Rail Pressure.
Check that the internal fuel pressure of the common rail assembly is within the specification below.
Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure when engine is idling after warming up the engine.
OK
(See pageEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>CHECK FOR INTERMITTENT PROBLEMS)
NG
Disconnect the suction control valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z64-1 (+B) - C45- 104 (PCV+) | Always | Below 1 Ω |
| z64-2 (PCV) - C45-105 (PCV-) | Always | Below 1 Ω |
| z64-1 (+B) or C45- 104 (PCV+) - Body ground | Always | 10 kΩ or higher |
| z64-2 (PCV) or C45-105 (PCV-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z64-1 (+B) - C46- 104 (PCV+) | Always | Below 1 Ω |
| z64-2 (PCV) - C46-105 (PCV-) | Always | Below 1 Ω |
| z64-1 (+B) or C46- 104 (PCV+) - Body ground | Always | 10 kΩ or higher |
| z64-2 (PCV) or C46-105 (PCV-) - Body ground | Always | 10 kΩ or higher |
Reconnect the suction control valve connector.
Reconnect the ECM connector.
OK
NG
Repair or replace the harness or connector.
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Data List / Common Rail Pressure and Target Common Rail Pressure.
Take a snapshot with the GTS during the Active Test.
Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Common Rail Pressure) when the "Test the Fuel Leak" Active Test is performed (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DATA LIST / ACTIVE TEST).
In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.
The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.
"Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.
"Common Rail Pressure" is the actual fuel pressure.
| Result | Proceed to |
|---|---|
| The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa. | B |
| Except above | A |
A
B
Clean the fuel filter case and replace the fuel filter.
Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.
NEXT
Replace the fuel supply pump assembly (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL).
NEXT
Bleed the air from the fuel system (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SYSTEM(w/ DPF)>ON-VEHICLE INSPECTION).
Perform PM forced regeneration (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).
When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.
NEXT
Perform supply pump initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DTC CHECK / CLEAR).
Turn the ignition switch off for 30 seconds or more.
Start the engine.
Idle the engine for 60 seconds, and then run it at 2500 rpm without load for 60 seconds.
Confirm that the DTC is not output again.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Engine and ECT / Utility / All Readiness.
Input DTC P1229.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, increase the idling time.
NEXT