The fuel temperature sensor monitors the fuel temperature. The fuel temperature sensor has a thermistor that varies its resistance depending on the fuel temperature. When the fuel temperature is low, the resistance of the thermistor is high. When the temperature is high, the resistance is low. The variations of resistance are communicated to the ECM as changes of voltage (See Fig. 1).
The fuel temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the fuel temperature sensor from terminal THF via resistor R.
Resistor R and the fuel temperature sensor are connected in series. When the resistance value of the fuel temperature sensor changes due to a change in fuel temperature, the voltage at terminal THF also changes. Based on this signal, the ECM corrects the pressure control compensation of the fuel supply pump assembly.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Ignition switch ON for 0.5 seconds | Open or short in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic). | ·
Open or short in fuel temperature sensor circuit ·
Fuel temperature sensor (fuel supply pump assembly) ·
ECM |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Ignition switch ON for 0.5 seconds | Short in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic). | ·
Short in fuel temperature sensor circuit ·
Fuel temperature sensor (fuel supply pump assembly) ·
ECM |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Ignition switch ON for 0.5 seconds | Open in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic). | ·
Open in fuel temperature sensor circuit ·
Fuel temperature sensor (fuel supply pump assembly) ·
ECM |
| DTC No. | Data List |
|---|---|
| P0180
P0182 P0183 |
Fuel Temperature |
If DTC P0180, P0182 and/or P0183 is stored, the following symptoms may appear:
Misfire
Combustion noise
Black smoke
Lack of power
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Engine and ECT / Data List / Fuel Temperature.
Read the value.
Same as the actual fuel temperature
| Result | Proceed to |
|---|---|
| -40°C (-40°F) | A |
| 140°C (284°F) or higher | B |
| OK (Same as actual fuel temperature) | C |
If there is an open circuit, the GTS indicates -40°C (-40°F).
If there is a short circuit, the GTS indicates 140°C (284°F) or higher.
A
B
C
Disconnect the fuel temperature sensor connector.
Connect terminals 2 and 1 of the fuel temperature sensor connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Engine and ECT / Data List / Fuel Temperature.
Read the value.
140°C (284°F) or higher
| *1 | Fuel Temperature Sensor |
| *2 | ECM |
| *a | Front view of wire harness connector
(to Fuel Temperature Sensor) |
Reconnect the fuel temperature sensor connector.
NG
OK
Disconnect the fuel temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z65-2 (THF) - C45-116 (THF) | Always | Below 1 Ω |
| z65-1 (E2) - C45-92 (E2) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z65-2 (THF) - C46-116 (THF) | Always | Below 1 Ω |
| z65-1 (E2) - C46-92 (E2) | Always | Below 1 Ω |
Reconnect the fuel temperature sensor connector.
Reconnect the ECM connector.
OK
NG
Replace the ECM (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Disconnect the fuel temperature sensor connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Engine and ECT / Data List / Fuel Temperature.
Read the value.
-40°C (-40°F)
| *1 | Fuel Temperature Sensor |
| *2 | ECM |
Reconnect the fuel temperature sensor connector.
OK
NG
Replace the fuel temperature sensor (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL TEMPERATURE SENSOR>REMOVAL).
NEXT
Disconnect the fuel temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z65-2 (THF) or C45-116 (THF) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z65-2 (THF) or C46-116 (THF) - Body ground | Always | 10 kΩ or higher |
Reconnect the fuel temperature sensor connector.
Reconnect the ECM connector.
OK
NG
Replace the ECM (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Bleed the air from the fuel system (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SYSTEM(w/ DPF)>ON-VEHICLE INSPECTION).
Perform PM forced regeneration (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).
When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.
NEXT
Perform supply pump initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
NEXT
Repair or replace the harness or connector.
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DTC CHECK / CLEAR).
Turn the ignition switch to ON for 1 second or more.
Enter the following menus: Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
NEXT