Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P2564  Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low  P2565  Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit High  P2588  Turbocharger/Supercharger Boost Control Position Sensor "B" Circuit Low  P2589  Turbocharger/Supercharger Boost Control Position Sensor "B" Circuit High  


DESCRIPTION

The variable nozzle vane type turbocharger consists primarily of a compressor wheel, turbine wheel, nozzle vane, unison ring, DC motor and nozzle vane position sensor.

The nozzle vane position sensor consists of a Hall IC and a magnetic yoke that rotates in unison with the movement of the linkage that actuates the nozzle vane. The nozzle vane position sensor converts the changes in the magnetic flux that are caused by the rotation of the DC motor (hence, the rotation of the magnetic yoke) into electric signals, and outputs them to the ECM. The ECM determines the actual nozzle vane position from the electric signals in order to calculate the target nozzle vane position.

A221597E02
4.208,1.427 4.208,0.583 false 4.208,0.583 4.563,0.583 false 1.365,3.073 1.49,3.313 true 1.052,2.302 0.677,1.281 0.677,1.281 0.802,1.281 true 1.354,1.75 1.531,1.271 true 1.542,1.271 1.635,1.271 false 0.51,3.917 2.313,4.458 1.802,0.542 10 false Nozzle Vane Position Sensor (Turbocharger Sub-assembly) 0.833,1.188 1.302,1.354 0.469,0.167 10 false Hall IC 2.354,2.458 2.75,2.635 0.396,0.177 10 false VTA1 2.979,3.135 3.375,3.313 0.396,0.177 10 false VNE2 3,1.583 3.458,1.76 0.458,0.177 10 false VNVC 3.115,3.552 3.5,3.771 0.385,0.219 10 false ECM 4.708,3.604 5.229,3.833 0.521,0.229 10 false Closed 5.75,3.594 6.365,3.865 0.615,0.271 10 false Opened 1.688,1.188 2.167,1.365 0.479,0.177 10 false Magnet 4.635,0.479 6.448,1.167 1.813,0.688 10 false Nozzle Vane Position Sensor Output Voltage (V) 0.063,2.729 0.531,3.177 0.469,0.448 10 false Sensor Vane 4.104,1.531 4.365,1.708 0.26,0.177 10 false 4.5 4.104,2.396 4.375,2.573 0.271,0.177 10 false 0.5 1.458,3.333 1.948,3.615 0.49,0.281 10 false Magnet 4.792,3.271 6.188,3.458 1.396,0.188 10 true Nozzle Vane Position 2.333,1.677 2.792,1.854 0.458,0.177 10 false VNVC 3,2.365 3.396,2.542 0.396,0.177 10 false VNA 2.333,3.25 2.75,3.521 0.417,0.271 10 false VNE2

P2564 (Bank 1), P2588 (Bank 2)
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 1 second VNA or VNA2 voltage is 0.1 V or less for 2.1 seconds (1 trip detection logic).
·

Nozzle vane position sensor (turbocharger sub-assembly)

·

Open or short in nozzle vane position sensor circuit

·

ECM



P2565 (Bank 1), P2589 (Bank 2)
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 1 second VNA or VNA2 voltage is 4.9 V or higher for 2.1 seconds (1 trip detection logic).
·

Nozzle vane position sensor (turbocharger sub-assembly)

·

Open or short in nozzle vane position sensor circuit

·

ECM



HINT:

If DTC P2564, P2565, P2588 and/or P2589 is stored due to the nozzle vane being stuck open, the following symptoms may appear:

- Lack of power

- Vehicle surge or hesitation under light or medium load



WIRING DIAGRAM

A165736E07
1.846,1.119 2.258,1.313 0.412,0.194 10 VNVC 1.874,1.434 2.252,1.628 0.378,0.194 10 VTA1 1.846,1.798 2.305,1.992 0.459,0.194 10 VNE2 5.265,1.119 5.691,1.313 0.427,0.194 10 VNVC 5.265,1.434 5.691,1.628 0.427,0.194 10 VNA 5.265,1.798 5.740,1.992 0.475,0.194 10 VNE2 2.381,1.205 2.565,1.388 0.184,0.184 10 3 2.381,1.534 2.565,1.718 0.184,0.184 10 1 2.381,1.884 2.565,2.068 0.184,0.184 10 2 4.926,1.205 5.193,1.388 0.267,0.184 10 120 4.968,1.534 5.152,1.718 0.184,0.184 10 74 5.265,3.605 5.719,3.799 0.455,0.194 10 VNA2 4.926,3.706 5.231,3.889 0.305,0.184 10 117 4.968,1.884 5.152,2.068 0.184,0.184 10 97 0.676,1.973 0.992,2.150 0.316,0.177 10 C89 0.648,2.155 3.311,2.561 2.663,0.406 10 Nozzle Vane Position Sensor (Turbocharger Sub-assembly (for Bank 1)) 1.841,3.267 2.293,3.461 0.452,0.194 10 VNC2 1.925,3.598 2.267,3.792 0.341,0.194 10 VTI2 1.925,3.963 2.246,4.157 0.320,0.194 10 VE2 2.381,3.353 2.565,3.537 0.184,0.184 10 3 2.381,3.699 2.565,3.882 0.184,0.184 10 1 2.381,4.049 2.565,4.232 0.184,0.184 10 2 0.676,4.11 0.955,4.286 0.279,0.177 10 z66 3.99,5.054 4.729,5.231 0.739,0.177 10 *1: for LHD 3.99,5.371 4.729,5.547 0.739,0.177 10 *2: for RHD 0.606,4.292 3.304,4.677 2.698,0.385 10 Nozzle Vane Position Sensor (Turbocharger Sub-assembly (for Bank 2)) 5.422,4.632 6.311,4.812 0.889,0.180 10 C45*1, C46*2 5.422,4.793 5.786,4.973 0.364,0.180 10 ECM

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P2564 P2565, P2588 OR P2589)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
P2564 P2565, P2588 or P2589 is output A
P2564 P2565, P2588 or P2589 and other DTCs are output B



A

2.CHECK HARNESS AND CONNECTOR (ECM - NOZZLE VANE POSITION SENSOR)

B

2.CHECK HARNESS AND CONNECTOR (ECM - NOZZLE VANE POSITION SENSOR)
a.

Disconnect the nozzle vane position sensor connector.


b.

Disconnect the ECM.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C89-3 (VNVC) - C45-120 (VNVC) Always Below 1 Ω
C89-2 (VNE2) - C45-97 (VNE2) Always Below 1 Ω
C89-1 (VTA1) - C45-74 (VNA) Always Below 1 Ω
z66-3 (VNC2) - C45-120 (VNVC) Always Below 1 Ω
z66-2 (VE2) - C45-97 (VNE2) Always Below 1 Ω
z66-1 (VTI2) - C45-117 (VNA2) Always Below 1 Ω
C89-3 (VNVC) or C45-120 (VNVC) - Body ground Always 10 kΩ or higher
C89-1 (VTA1) or C45-74 (VNA) - Body ground Always 10 kΩ or higher
z66-3 (VNC2) or C45-120 (VNVC) - Body ground Always 10 kΩ or higher
z66-1 (VTI2) or C45-117 (VNA2) - Body ground Always 10 kΩ or higher


Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C89-3 (VNVC) - C46-120 (VNVC) Always Below 1 Ω
C89-2 (VNE2) - C46-97 (VNE2) Always Below 1 Ω
C89-1 (VTA1) - C46-74 (VNA) Always Below 1 Ω
z66-3 (VNC2) - C46-120 (VNVC) Always Below 1 Ω
z66-2 (VE2) - C46-97 (VNE2) Always Below 1 Ω
z66-1 (VTI2) - C46-117 (VNA2) Always Below 1 Ω
C89-3 (VNVC) or C46-120 (VNVC) - Body ground Always 10 kΩ or higher
C89-1 (VTA1) or C46-74 (VNA) - Body ground Always 10 kΩ or higher
z66-3 (VNC2) or C46-120 (VNVC) - Body ground Always 10 kΩ or higher
z66-1 (VTI2) or C46-117 (VNA2) - Body ground Always 10 kΩ or higher



d.

Reconnect the nozzle vane position sensor connector.


e.

Reconnect the ECM connector.



OK

3.INSPECT ECM (VNVC VOLTAGE)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.INSPECT ECM (VNVC VOLTAGE)
a.
U163419E01
0.217,0.089 0.456,0.255 0.240,0.165 10 *a 0.223,0.642 0.517,0.843 0.294,0.201 10 C89 0.418,1.738 1.436,1.911 1.017,0.174 10 VNE2*A, VE2*B 1.84,1.578 3.116,1.802 1.276,0.224 10 VNVC*A, VNC2*B 1.473,1.045 0.631,1.738 false 1.602,1.06 1.914,1.578 false 0.698,0.651 0.938,0.816 0.240,0.165 10 *A 0.258,1.157 0.522,1.358 0.264,0.201 10 z66 0.698,1.166 0.938,1.332 0.240,0.165 10 *B

Disconnect the nozzle vane position sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C89-3 (VNVC) - C89-2 (VNE2) Engine switch on (IG) 4.5 to 5.5 V
z66-3 (VNC2) - z66-2 (VE2) Engine switch on (IG) 4.5 to 5.5 V


Text in Illustration
*A for Bank 1
*B for Bank 2
*a Front view of wire harness connector
(to Nozzle Vane Position Sensor)



OK

4.REPLACE TURBOCHARGER SUB-ASSEMBLY (NOZZLE VANE POSITION SENSOR)

NG

5.REPLACE ECM
4.REPLACE TURBOCHARGER SUB-ASSEMBLY (NOZZLE VANE POSITION SENSOR)

When DTC P2564 or P2565 is output:

·

Replace the turbocharger sub-assembly (for bank 1) (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>REMOVAL).


When DTC P2588 or P2589 is output:

·

Replace the turbocharger sub-assembly (for bank 2) (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>REMOVAL).



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE ECM

NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off and leave the vehicle for 15 seconds.


d.

Turn the engine switch on (IG) for 1 second.


e.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Engine and ECT / Utility / All Readiness.


ii.

Input DTC P2564 P2565, P2588 or P2589.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, idle the engine.




NEXT

END