Home › Engine / Hybrid System › 1VD-FTV (INTAKE / EXHAUST) › EXHAUST MANIFOLD W/ TURBOCHARGER › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052790 1VD-FTV INTAKE / EXHAUST _0255173 EXHAUST MANIFOLD W/ TURBOCHARGER A

1VD-FTV INTAKE / EXHAUST  EXHAUST MANIFOLD W/ TURBOCHARGER  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

w/ DPF:

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines,


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 11452 4.REMOVE NO. 1 ENGINE OIL LEVEL DIPSTICK GUIDE (for Bank 1)

a.
A170301

Remove the 2 bolts and No. 1 engine oil level dipstick guide.


b.

Remove the O-ring from the No. 1 engine oil level dipstick.


Hide 17875 5.REMOVE NO. 1 INTAKE AIR CONNECTOR PIPE (for Bank 1)

a.
A174753

Disconnect the 4 connectors.


b.

Using a clip remover, detach the 5 wire harness clamps.


c.
A177381

Loosen the hose clamp, and remove the bolt and No. 1 intake air connector pipe.


Hide 12262 6.REMOVE NO. 2 VENTILATION HOSE (for Bank 1)

A264021E03
0.104,0.115 0.375,0.354 0.271,0.24 10 true *A 0.104,2.458 0.438,2.719 0.333,0.26 10 true *B

Text in Illustration
*A w/ DPF
*B w/o DPF

Hide 16285 7.REMOVE NO. 2 TURBO WATER HOSE (for Bank 1)

A267247

Hide 8.REMOVE BREATHER PLUG RH (for Bank 1)

a.
A267248

Disconnect the hose.


b.

Detach the clamp and remove the breather plug RH.


Hide 17167 9.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (for Bank 1)

a.
A264022E03
0.104,0.115 0.479,0.406 0.375,0.292 10 true *A 0.104,2.458 0.458,2.75 0.354,0.292 10 true *B

Remove the 3 bolts and No. 1 exhaust manifold heat insulator.

Text in Illustration
*A w/ DPF
*B w/o DPF


Hide 15474A 10.DISCONNECT NO. 1 OUTLET TURBO OIL HOSE (for Bank 1)

A267249

Hide 16027 11.REMOVE NO. 1 TURBO WATER PIPE SUB-ASSEMBLY (for Bank 1)

a.
A177401

Disconnect the water hose.


b.

Remove the 3 bolts, 2 nuts, No. 1 turbo water pipe and gasket.


Hide 17293 12.REMOVE NO. 1 TURBOCHARGER STAY (for Bank 1)

a.
A177403

Remove the 2 bolts and No. 1 turbocharger stay.


Hide 12201 13.REMOVE NO. 1 VENTILATION TUBE SUB-ASSEMBLY (for Bank 1)

a.
A264023

Disconnect the hose.


b.

Remove the union bolt, bolt, No. 1 ventilation tube and gasket.


Hide 17201 14.REMOVE NO. 1 TURBOCHARGER SUB-ASSEMBLY WITH EXHAUST MANIFOLD RH (for Bank 1)

a.
A177405

Remove the union bolt and gasket, and disconnect the No. 1 inlet turbo oil pipe from the cylinder block.


b.

Remove the 10 nuts, 10 collars and No. 1 turbocharger with exhaust manifold RH.

A264024E01
0.102,0.069 0.287,0.224 0.185,0.155 10 *A 3.954,0.069 4.139,0.224 0.185,0.155 10 *B

Text in Illustration
*A w/ DPF *B w/o DPF


c.

Remove the gasket.


d.
A264026

w/ DPF:

Remove the 4 bolts, No. 1 exhaust manifold pipe and 2 gaskets.


e.

Remove the 2 nuts and bolt, and separate the No. 1 turbocharger and exhaust manifold RH.

A264025E01
0.477,0.096 0.662,0.251 0.185,0.155 10 *A 3.942,0.096 4.127,0.251 0.185,0.155 10 *B

Text in Illustration
*A w/ DPF *B w/o DPF


f.

Remove the gasket from the No. 1 turbocharger.


Hide 17274 15.REMOVE NO. 1 INLET COMPRESSOR ELBOW (for Bank 1)

a.
A174717

Remove the 2 bolts, No. 1 inlet compressor elbow and gasket.


Hide 15481 16.REMOVE NO. 1 TURBO OIL PIPE (for Bank 1)

a.
A170298

Remove the 2 bolts, No. 1 turbo oil pipe and gasket.


Hide 15407 17.REMOVE NO. 1 INLET TURBO OIL PIPE SUB-ASSEMBLY (for Bank 1)

a.
A170313

Remove the union bolt, bolt, No. 1 inlet turbo oil pipe and gasket.


Hide 12263 18.REMOVE NO. 3 VENTILATION HOSE (for Bank 2)

A264027E03
0.083,0.115 0.427,0.427 0.344,0.313 10 true *A 0.083,2.458 0.479,2.823 0.396,0.365 10 true *B

Text in Illustration
*A w/ DPF
*B w/o DPF

Hide 19.REMOVE BREATHER PLUG LH (for Bank 2)

a.
A267263E03
0.104,0.083 0.417,0.344 0.313,0.26 10 true *A 0.104,2.563 0.396,2.833 0.292,0.271 10 true *B

Disconnect the hose.

Text in Illustration
*A w/ DPF
*B w/o DPF


b.

w/o DPF:

Detach the clamp.


c.

Remove the breather plug LH.


Hide 16287 20.REMOVE NO. 2 TURBO WATER HOSE (for Bank 2)

A267250

Hide 17168 21.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR (for Bank 2)

a.
A264028E03
0.083,0.115 0.406,0.354 0.323,0.24 10 true *A 0.083,2.458 0.427,2.719 0.344,0.26 10 true *B

Remove the 3 bolts and No. 2 exhaust manifold heat insulator.

Text in Illustration
*A w/ DPF
*B w/o DPF


Hide 16029 22.REMOVE NO. 3 TURBO WATER PIPE SUB-ASSEMBLY (for Bank 2)

a.
A177386

Remove the 2 bolts, union bolt, No. 3 turbo water pipe and gasket.


Hide 16355 23.REMOVE FRONT WATER BY-PASS JOINT (for Bank 2)

a.
A177435

Remove the front water by-pass joint and gasket.


Hide 16028 24.REMOVE NO. 2 TURBO WATER PIPE SUB-ASSEMBLY (for Bank 2)

a.
A267251

Disconnect the water hose.


b.

Remove the union bolt, bolt, No. 2 turbo water pipe and gasket.


Hide 15492 25.REMOVE NO. 2 OUTLET TURBO OIL HOSE (for Bank 2)

A267252

Hide 17297 26.REMOVE NO. 2 TURBOCHARGER STAY (for Bank 2)

a.
A267253

Remove the 2 bolts and No. 2 turbocharger stay.


Hide 12202 27.REMOVE NO. 2 VENTILATION TUBE SUB-ASSEMBLY (for Bank 2)

a.

Disconnect the hose.

A264029E01
0.518,0.039 0.703,0.194 0.185,0.155 10 *A 3.711,0.039 3.896,0.194 0.185,0.155 10 *B

Text in Illustration
*A w/ DPF *B w/o DPF


b.

Remove the union bolt, bolt, No. 2 ventilation tube and gasket.


Hide 17208 28.REMOVE NO. 2 TURBOCHARGER SUB-ASSEMBLY WITH EXHAUST MANIFOLD LH (for Bank 2)

a.
A179471

Disconnect the 2 connectors from the turbocharger.


b.
A177391

Remove the union bolt and gasket, and disconnect the No. 2 inlet turbo oil pipe from the No. 1 oil pan.


c.

Remove the 10 nuts, 10 collars and No. 2 turbocharger with exhaust manifold LH.

A264030E03
0.302,0.073 0.49,0.229 0.188,0.156 10 false *A 4.073,0.073 4.26,0.229 0.188,0.156 10 false *B

Text in Illustration
*A w/ DPF *B w/o DPF


d.

Remove the gasket.


e.
A264032

w/ DPF:

Remove the 4 bolts, No. 2 exhaust manifold pipe and 2 gaskets.


f.
A264031E01
0.294,0.187 0.479,0.342 0.185,0.155 10 *A 0.294,2.823 0.479,2.978 0.185,0.155 10 *B

Remove the 3 nuts, and separate the No. 2 turbocharger and exhaust manifold LH.

Text in Illustration
*A w/ DPF
*B w/o DPF


g.

Remove the gasket from the turbocharger.


Hide 17286 29.REMOVE NO. 2 INLET COMPRESSOR ELBOW (for Bank 2)

a.
A174716

Remove the 2 bolts, No. 2 inlet compressor elbow and gasket.


Hide 15482 30.REMOVE NO. 2 TURBO OIL PIPE (for Bank 2)

a.
A170314

Remove the 2 bolts, No. 2 turbo oil pipe and gasket.


Hide 15408G 31.REMOVE NO. 2 INLET TURBO OIL PIPE SUB-ASSEMBLY (for Bank 2)

a.
A177395

Remove the union bolt, bolt, No. 2 inlet turbo oil pipe and gasket.


Hide 32.REPLACE STUD BOLT

HINT:

If a stud bolt is deformed or its threads are damaged, replace it.


a.

For No. 1 Turbocharger:

i.

Using an E10 "TORX" wrench, replace the stud bolts labeled A and B shown in the illustration below.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


ii.

Replace the stud bolts labeled C shown in the illustration below.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)

U163073E02
2.948,0.698 2.792,0.698 2.792,0.698 2.365,1.708 false 2.802,2.521 2.646,2.521 2.646,2.521 2.365,2.135 false 4.656,1.083 4.49,1.083 4.49,1.083 4.219,1.729 false 4.646,2.51 4.479,2.51 4.479,2.51 4.208,2.125 false 6.427,1.458 6.26,1.458 6.26,1.458 6.01,1.771 false 6.01,2.115 6.427,2.115 false 1.313,1.656 1.885,2 0.573,0.344 10 false 41.4 mm (1.63 in.) 3.01,0.625 4.125,0.792 1.115,0.167 10 false 18 mm (0.709 in.) 2.875,2.448 3.99,2.615 1.115,0.167 10 false 13 mm (0.512 in.) 4.708,1 5.823,1.177 1.115,0.177 10 false 20 mm (0.787 in.) 4.688,2.417 5.813,2.583 1.125,0.167 10 false 14 mm (0.551 in.) 3.146,1.667 3.729,2.01 0.583,0.344 10 false 39.5 mm (1.56 in.) 4.938,1.75 5.583,2.094 0.646,0.344 10 false 23.5 mm (0.925 in.) 6.469,1.385 7.115,1.729 0.646,0.344 10 false 9.0 mm (0.354 in.) 6.479,2.042 7.125,2.385 0.646,0.344 10 false 9.0 mm (0.354 in.) 2.104,1.208 2.26,1.375 0.156,0.167 10 false A 3.938,1.26 4.094,1.427 0.156,0.167 10 false B 5.75,1.417 5.906,1.583 0.156,0.167 10 false C 0.385,0.49 0.542,0.656 0.156,0.167 10 false A 1.542,0.802 1.698,0.969 0.156,0.167 10 false B 0.333,0.865 0.49,1.031 0.156,0.167 10 false C 0.865,0.313 1.021,0.479 0.156,0.167 10 false A 0.323,1.146 0.479,1.323 0.156,0.177 10 false C 1.354,0.99 1.51,1.156 0.156,0.167 10 false B 1.469,1.281 1.625,1.448 0.156,0.167 10 false B



b.
A177308E02
1.823,2.344 2.938,2.521 1.115,0.177 10 false 20 mm (0.787 in.) 1.823,2.844 2.948,3.01 1.125,0.167 10 false 14 mm (0.551 in.) 0.385,2.479 0.969,2.823 0.583,0.344 10 false 39.5 mm (1.56 in.)

For No. 2 Turbocharger:

Using an E10 "TORX" wrench, replace the stud bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


c.
A264033E02
1.99,3.594 3.104,3.771 1.115,0.177 10 false 20 mm (0.787 in.) 1.99,4.083 3.115,4.25 1.125,0.167 10 false 14 mm (0.551 in.) 0.594,3.719 1.177,4.063 0.583,0.344 10 false 39.5 mm (1.56 in.) 0.115,0.167 0.302,0.323 0.188,0.156 10 false *A 0.115,1.927 0.302,2.083 0.188,0.156 10 false *B

For Exhaust Manifold LH:

Text in Illustration
*A w/ DPF
*B w/o DPF

Using an E10 "TORX" wrench, replace the stud bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)