Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0548  Exhaust Gas Temperature Sensor Circuit Low (Bank 2 Sensor 1)  P0549  Exhaust Gas Temperature Sensor Circuit High (Bank 2 Sensor 1)  P2035  Exhaust Gas Temperature Sensor Circuit Low (Bank 2 Sensor 2)  P2036  Exhaust Gas Temperature Sensor Circuit High (Bank 2 Sensor 2)  P2468  Exhaust Gas Temperature Sensor Circuit Low (Bank 2 Sensor 3)  P2469  Exhaust Gas Temperature Sensor Circuit High (Bank 2 Sensor 3)  


DESCRIPTION

A243953E05
5.75,4.677 5.948,4.677 false 1.76,5.427 1.875,5.427 false 1.563,2.573 1.125,2.958 false 1.552,1.677 1.219,1.042 1.219,1.042 1.125,1.042 false 2.24,1.323 2.854,0.281 2.854,0.281 4,0.281 false 2.458,2.865 3.885,3.365 3.885,3.365 4.083,3.365 false 2.458,2.052 4.49,2.219 4.49,2.219 4.604,2.219 false 4.125,0.167 6.25,0.479 2.125,0.313 10 false Exhaust Gas Temperature Sensor (B1S1) 1.521,0.542 2.365,0.719 0.844,0.177 10 false Exhaust Gas 3.167,0.927 3.531,1.094 0.365,0.167 10 false ECM 0.219,2.906 1.208,3.24 0.99,0.333 10 false DPF Catalytic Converter 4.625,2.146 7.115,2.49 2.49,0.344 10 false No. 2 Exhaust Gas Temperature Sensor (B1S2) 0.24,3.792 1.979,3.979 1.74,0.188 10 false Property of Output Voltage: 1.646,4.198 3.313,4.396 1.667,0.198 10 false Exhaust Gas Temperature 3.427,4.208 3.938,4.385 0.51,0.177 10 false °C (°F) 0.833,4.198 1.635,4.365 0.802,0.167 10 false 1000 (1832) 0.917,4.417 1.615,4.583 0.698,0.167 10 false 960 (1760) 0.917,4.646 1.615,4.813 0.698,0.167 10 false 760 (1400) 0.906,4.875 1.604,5.042 0.698,0.167 10 false 560 (1040) 0.969,5.104 1.594,5.271 0.625,0.167 10 false 360 (680) 0.969,5.344 1.604,5.51 0.635,0.167 10 false 160 (320) 1.021,5.615 1.604,5.781 0.583,0.167 10 false -40 (-40) 1.552,5.698 1.646,5.917 0.094,0.219 10 false 0 1.708,5.698 1.927,5.885 0.219,0.188 10 false 0.2 1.99,5.698 2.229,5.885 0.24,0.188 10 false 0.5 2.385,5.698 2.625,5.885 0.24,0.188 10 false 1.0 2.833,5.688 3.073,5.875 0.24,0.188 10 false 1.5 3.271,5.688 3.51,5.875 0.24,0.188 10 false 2.0 3.719,5.688 3.958,5.875 0.24,0.188 10 false 2.5 4.177,5.688 4.417,5.875 0.24,0.188 10 false 3.0 4.604,5.698 4.813,5.885 0.208,0.188 10 false 3.5 5.031,5.688 5.24,5.875 0.208,0.188 10 false 4.0 5.49,5.698 5.708,5.885 0.219,0.188 10 false 4.5 5.75,5.698 6.063,5.885 0.313,0.188 10 false 4.95 6.052,5.688 6.281,5.875 0.229,0.188 10 false 5.0 2.635,6.104 5.51,6.313 2.875,0.208 10 false Exhaust Gas Temperature Sensor Voltage (V) 1.917,5.365 4.24,5.521 2.323,0.156 10 false Stores P0545, P2032 or P242C 3.823,4.625 5.813,4.781 1.99,0.156 10 false Stores P0546, P2033 or P242D 4.135,3.281 6.75,3.656 2.615,0.375 10 false No. 3 Exhaust Gas Temperature Sensor (B1S3) 0.24,0.958 1.229,1.292 0.99,0.333 10 false CCo Catalytic Converter

The exhaust gas temperature sensors are installed before and after the DPF catalytic converter and before the CCo catalytic converter to sense the exhaust gas temperature.

A thermistor built into the sensor changes its resistance value according to the exhaust gas temperature. The lower the exhaust gas temperature, the higher the thermistor resistance value. The higher the exhaust gas temperature, the lower the thermistor resistance value.

The exhaust gas temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the exhaust gas temperature sensor from terminal TCF2 (B2S1), TCI2 (B2S2) and TCO2 (B2S3) via resistor R.

Resistor R and the exhaust gas temperature sensor are connected in series. When the resistance value of the exhaust gas temperature sensor changes in accordance with the exhaust gas temperature, the voltage at terminals TCF2 (B2S1), TCI2 (B2S2) and TCO2 (B2S3) also changes. The exhaust gas temperature sensor monitors the temperature upstream of the CCo catalyst converter. The No. 3exhaust gas temperature sensor monitors the temperature upstream of the DPF catalyst converter. The No. 4 exhaust gas temperature sensor monitors the rise in temperature of the DPF catalyst converter. When PM forced regeneration is needed, the ECM operates the exhaust fuel addition injector assembly to obtain target upstream temperature of the DPF catalytic converter as monitored through sensor 2. In addition, the ECM monitors the temperature increase of the DPF catalytic converter using sensor 3.

P0548
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Idle the engine for 3 seconds after warming up the engine (the engine coolant temperature is 60°C (140°F) or higher) and allowing 11 minutes to elapse after starting the engine. Exhaust gas temperature sensor (B2S1) output voltage is below 0.2 V for 3 seconds or more when all conditions are met. (1 trip detection logic):
·

After starting the engine, 11 minutes or more elapses

·

Engine is running

·

Coolant temperature is 60°C (140°F) or more


·

Open or short in exhaust gas temperature sensor (B2S1) circuit

·

Exhaust gas temperature sensor (B2S1)

·

ECM



P0549
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Idle the engine for 3 seconds after warming up the engine (the engine coolant temperature is 60°C (140°F) or higher) and allowing 11 minutes to elapse after starting the engine. Exhaust gas temperature sensor (B2S1) output voltage is higher than 4.95 V for 3 seconds or more when all conditions are met. (1 trip detection logic):
·

After starting the engine, 11 minutes or more elapses

·

Engine is running

·

Coolant temperature is 60°C (140°F) or more


·

Open or short in exhaust gas temperature sensor (B2S1) circuit

·

Exhaust gas temperature sensor (B2S1)

·

ECM



P2035
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Idle the engine for 3 seconds after warming up the engine (the engine coolant temperature is 60°C (140°F) or higher) and allowing 11 minutes to elapse after starting the engine. No. 3 exhaust gas temperature sensor (B2S2) output voltage is below 0.2 V for 3 seconds or more when all conditions are met. (1 trip detection logic):
·

After starting the engine, 11 minutes or more elapses

·

Engine is running

·

Coolant temperature is 60°C (140°F) or more


·

Open or short in No. 3 exhaust gas temperature sensor (B2S2) circuit

·

No. 3 exhaust gas temperature sensor (B2S2)

·

ECM



P2036
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Idle the engine for 3 seconds after warming up the engine (the engine coolant temperature is 60°C (140°F) or higher) and allowing 11 minutes to elapse after starting the engine. No. 3 exhaust gas temperature sensor (B2S2) output voltage is higher than 4.95 V for 3 seconds or more when all conditions are met. (1 trip detection logic):
·

After starting the engine, 11 minutes or more elapses

·

Engine is running

·

Coolant temperature is 60°C (140°F) or more


·

Open or short in No. 3 exhaust gas temperature sensor (B2S2) circuit

·

No. 3 exhaust gas temperature sensor (B2S2)

·

ECM



P2468
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Idle the engine for 3 seconds after warming up the engine (the engine coolant temperature is 60°C (140°F) or higher) and allowing 11 minutes to elapse after starting the engine. No. 4 exhaust gas temperature sensor (B2S3) output voltage is below 0.2 V for 3 seconds or more when all conditions are met. (1 trip detection logic):
·

After starting the engine, 11 minutes or more elapses

·

Engine is running

·

Coolant temperature is 60°C (140°F) or more


·

Open or short in No. 4 exhaust gas temperature sensor (B2S3) circuit

·

No. 4 exhaust gas temperature sensor (B2S3)

·

ECM



P2469
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Idle the engine for 3 seconds after warming up the engine (the engine coolant temperature is 60°C (140°F) or higher) and allowing 11 minutes to elapse after starting the engine. No. 4 exhaust gas temperature sensor (B2S3) output voltage is higher than 4.95 V for 3 seconds or more when all conditions are met. (1 trip detection logic):
·

After starting the engine, 11 minutes or more elapses

·

Engine is running

·

Coolant temperature is 60°C (140°F) or more


·

Open or short in No. 4 exhaust gas temperature sensor (B2S3) circuit

·

No. 4 exhaust gas temperature sensor (B2S3)

·

Abnormal rise in temperature due to melting of DPF catalytic converter

·

ECM



Related Data List
DTC No. Data List
P0548
P0549
Exhaust Temperature B2S1
P2035
P2036
Exhaust Temperature B2S2
P2468
P2469
Exhaust Temperature B2S3

HINT:
·

DTC P20D5 (Exhaust fuel addition injector assembly (for bank 2) malfunction) may be stored if there is an open malfunction in an exhaust gas temperature sensor circuit.

·

Sensor 1 represents the sensor located upstream of the CCo catalytic converter.

·

Sensor 2 represents the sensor located upstream of the DPF catalytic converter.

·

Sensor 3 represents the sensor located downstream of the DPF catalytic converter.

·

When DTC P0548, P0549, P2035, P2036, P2468 and/or P2469 is output, check the upstream and downstream exhaust gas temperature indicated by "Engine and ECT / Exhaust Temperature B2S1, Exhaust Temperature B2S2 and Exhaust Temperature B2S3" using the GTS.


Reference:
Condition Exhaust Gas Temperature Exhaust Gas Temperature Sensor Condition
Idling after warm-up Constant at between 50 and 700°C (122 and 1292°F) Normal
-40°C (-40°F) Open circuit
1000°C (1832°F) or higher Short circuit


MONITOR DESCRIPTION

The ECM constantly monitors the output voltages from the exhaust gas temperature sensors in order to detect problems with the sensors. When the sensor output voltage deviates from the normal operating range (between 0.2 V and 4.95 V) for more than 3 seconds after the engine is warmed up, the ECM interprets this as malfunction of the sensor circuit and illuminates the MIL.

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

If DTC P2469 is stored and the exhaust gas temperature sensor (B2S3) circuit is not malfunctioning, check if the DPF catalytic converter has melted as DTC P2469 may be stored when the DPF catalytic converter melts and the exhaust gas temperature sensor (B2S3) is exposed to high temperatures.



PROCEDURE

1.READ VALUE USING GTS (EXHAUST TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Data List / Exhaust Temperature B2S1, Exhaust Temperature B2S2 and Exhaust Temperature B2S3.


d.

Read the value.

Standard:

Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warm-up), and varies after an engine speed of 3000 rpm is maintained for 1 minute.


Result
Temperature Displayed Proceed to
-40°C (-40°F) (After warming up the engine) A
1000°C (1832°F) or higher B
OK: Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F]) during idling after warm-up, and varies after maintaining an engine speed of 3000 rpm for 1 minute after accelerating the engine from idling to 3000 rpm C

HINT:
·

If there is a short circuit, the GTS will indicate -40°C (-40°F).

·

If there is an open circuit, the GTS will indicate 1000°C (1832°F) or higher.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

6.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
U163707E02
0.219,0.125 0.385,0.292 0.167,0.167 10 false *1 2.271,0.125 2.448,0.26 0.177,0.135 10 false *2 0.313,3.271 0.5,3.427 0.188,0.156 10 false *a 0.313,3.667 0.479,3.833 0.167,0.167 10 false *b 2.417,1.031 2.885,1.177 0.469,0.146 10 false TCF2 2.417,1.208 2.854,1.354 0.438,0.146 10 false TCI2 2.49,2.063 2.917,2.229 0.427,0.167 10 false ETCF 0.771,3.396 1.146,3.552 0.375,0.156 10 false C164 2.417,1.385 2.854,1.531 0.438,0.146 10 false TCO2 0.313,4.063 0.479,4.229 0.167,0.167 10 false *c 0.771,3.76 1.135,3.917 0.365,0.156 10 false C165 0.792,4.104 1.146,4.26 0.354,0.156 10 false C167

Disconnect the C164, C165 or C167 exhaust gas temperature sensor connector.


b.

Connect terminals 1 and 2 of the exhaust gas temperature sensor wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Enter the following menus: Engine and ECT / Data List / Exhaust Temperature B2S1, Exhaust Temperature B2S2 and Exhaust Temperature B2S3.


f.

Read the value.

Standard:

1000°C (1832°F) or higher


Text in Illustration
*1 Exhaust Gas Temperature Sensor
*2 ECM
*a Front view of wire harness connector
(to Exhaust Gas Temperature Sensor (B2S1))
*b Front view of wire harness connector
(to No. 3 Exhaust Gas Temperature Sensor (B2S2))
*c Front view of wire harness connector
(to No. 4 Exhaust Gas Temperature Sensor (B2S3))


g.

Reconnect the exhaust gas temperature sensor connector.



OK

3.REPLACE EXHAUST GAS TEMPERATURE SENSOR

NG

4.CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR - ECM)
3.REPLACE EXHAUST GAS TEMPERATURE SENSOR
a.

b.

Replace the No. 3 exhaust gas temperature sensor (B2S2) (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR(for DPF)>REMOVAL).


c.

Replace the No. 4 exhaust gas temperature sensor (B2S3) (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR(for DPF)>REMOVAL).



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Disconnect the exhaust gas temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C164-2 (TCF2) - C45-68 (TCF2) Always Below 1 Ω
C164-1 (E2) - C45-99 (ETCF) Always Below 1 Ω
C165-2 (TCI2) - C45-98 (TCI2) Always Below 1 Ω
C165-1 (E2) - C45-99 (ETCF) Always Below 1 Ω
C167-2 (TCO2) - C45-124 (TCO2) Always Below 1 Ω
C167-1 (E2) - C45-99 (ETCF) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
C164-2 (TCF2) - C46-68 (TCF2) Always Below 1 Ω
C164-1 (E2) - C46-99 (ETCF) Always Below 1 Ω
C165-2 (TCI2) - C46-98 (TCI2) Always Below 1 Ω
C165-1 (E2) - C46-99 (ETCF) Always Below 1 Ω
C167-2 (TCO2) - C46-124 (TCO2) Always Below 1 Ω
C167-1 (E2) - C46-99 (ETCF) Always Below 1 Ω



d.

Reconnect the exhaust gas temperature sensor connector.


e.

Reconnect the ECM connector.



OK

5.REPLACE ECM

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE ECM

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A246636E05
0.371,0.315 0.569,0.485 0.198,0.170 10 *1 2.388,0.315 2.585,0.485 0.198,0.170 10 *2 2.418,1.381 2.802,1.551 0.384,0.170 10 TCF2 2.418,1.536 2.871,1.705 0.453,0.170 10 TCI2 2.521,2.366 2.974,2.536 0.453,0.170 10 ETCF 2.418,1.696 2.871,1.866 0.453,0.170 10 TCO2

Disconnect the C164, C165 or C167 exhaust gas temperature sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Engine and ECT / Data List / Exhaust Temperature B2S1, Exhaust Temperature B2S2 and Exhaust Temperature B2S3.


e.

Read the value.

Standard:

0°C (32°F)



f.

Reconnect the exhaust gas temperature sensor connector.

Text in Illustration
*1 Exhaust Gas Temperature Sensor
*2 ECM


g.

Reconnect the exhaust gas temperature sensor connector.



OK

7.REPLACE EXHAUST GAS TEMPERATURE SENSOR

NG

8.CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR - ECM)
7.REPLACE EXHAUST GAS TEMPERATURE SENSOR
a.

b.

Replace the No. 3 exhaust gas temperature sensor (B2S2) (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR(for DPF)>REMOVAL).


c.

Replace the No. 4 exhaust gas temperature sensor (B2S3) (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR(for DPF)>REMOVAL).



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Disconnect the exhaust gas temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C164-2 (TCF2) or C45-68 (TCF2) - Body ground Always 10 kΩ or higher
C165-2 (TCI2) or C45-98 (TCI2) - Body ground Always 10 kΩ or higher
C167-2 (TCO2) or C45-124 (TCO2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C164-2 (TCF2) or C46-68 (TCF2) - Body ground Always 10 kΩ or higher
C165-2 (TCI2) or C46-98 (TCI2) - Body ground Always 10 kΩ or higher
C167-2 (TCO2) or C46-124 (TCO2) - Body ground Always 10 kΩ or higher



d.

Reconnect the exhaust gas temperature sensor connector.


e.

Reconnect the ECM connector.



OK

9.REPLACE ECM

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.REPLACE ECM

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Start the engine.


d.

Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 60°C (140°F) or higher) and allowing 11 minutes to elapse after starting the engine.


e.

Enter the following menus: Engine and ECT / Trouble Codes.


f.

Confirm that the DTC is not output again.



NEXT

END