Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P011C  Charge Air Temperature/Intake Air Temperature Correlation (Bank 1)  


DESCRIPTION

Refer to DTC P007C (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P007C).

Refer to DTC P0112 (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P0112).

P011C
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
After engine completely warmed up, allow engine to soak for long time (10 hours or more).
Start the engine and idle the engine for 3 minutes or more.
After the engine is completely warmed up and then allowed to soak for a long time (10 hours or more), the difference in temperature at the intake air temperature sensor and intake air temperature sensor (turbo) after turbocharger after idling for 3 minutes is 25°C (59°F) or higher.
(2 trip detection logic)
·

Open or short in intake air temperature sensor circuit

·

Open or short in intake air temperature sensor (turbo) circuit

·

Intake air temperature sensor (built into mass air flow meter)

·

Intake air temperature sensor (turbo)

·

ECM

·

Engine off timer (P2610)



Related Data List
DTC No. Data List
P011C
·

Intake Air

·

Intake Air Temp (Turbo)



CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P011C)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
P011C is output A
P011C and other DTCs are output B



A

2.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)

B

2.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
a.

Allow the engine to soak for 1 to 2 hours.

HINT:
·

It is not necessary to allow the engine to soak if the engine is cold.

·

The engine cools faster if the hood is opened.




b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Engine and ECT / Data List / Coolant temp.


e.

Read the value.

OK:

The difference between the displayed value and outside air temperature is below 5°C (9°F).


NOTICE:

If the difference between "Coolant Temp" and the outside air temperature is 5°C (9°F) or higher, the heat from the engine affects the intake air temperature sensor, causing an incorrect value to be displayed. In this case, allow the engine to soak again.




NEXT

3.READ VALUE USING GTS (INTAKE AIR TEMPERATURE)
3.READ VALUE USING GTS (INTAKE AIR TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Data List / Intake Air.


d.

Read the value.

OK:

The difference between the displayed value and outside air temperature is below 15°C (27°F).




OK

4.READ VALUE USING GTS (INTAKE AIR TEMPERATURE (TURBO))

NG

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
4.READ VALUE USING GTS (INTAKE AIR TEMPERATURE (TURBO))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Data List / Intake Air Temp (Turbo).


d.

Read the value.

OK:

The difference between the displayed value and outside air temperature is below 15°C (27°F).




OK

5.REPLACE ECM

NG

8.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM)
5.REPLACE ECM

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C50-4 (THA) - C45-115 (THA) Always Below 1 Ω
C50-5 (E2) - C45-92 (E2) Always Below 1 Ω
C50-4 (THA) or C45-115 (THA) - Body ground Always 10 kΩ or higher


Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C50-4 (THA) - C46-115 (THA) Always Below 1 Ω
C50-5 (E2) - C46-92 (E2) Always Below 1 Ω
C50-4 (THA) or C46-115 (THA) - Body ground Always 10 kΩ or higher



d.

Reconnect the mass air flow meter connector.


e.

Reconnect the ECM connector.



OK

7.REPLACE MASS AIR FLOW METER

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.REPLACE MASS AIR FLOW METER
a.

Replace the mass air flow meter (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER (w/ DPF)>REMOVAL).

HINT:

If foreign matter is stuck inside the mass air flow meter, the output characteristics of the mass air flow meter may change, resulting in a malfunction.




NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM)
a.

Disconnect the intake air temperature sensor (turbo) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C79-2 - C45-90 (THIA) Always Below 1 Ω
C79-1 - C45-92 (E2) Always Below 1 Ω
C79-2 or C45-90 (THIA) - Body ground Always 10 kΩ or higher


Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C79-2 - C46-90 (THIA) Always Below 1 Ω
C79-1 - C46-92 (E2) Always Below 1 Ω
C79-2 or C46-90 (THIA) - Body ground Always 10 kΩ or higher



d.

Reconnect the intake air temperature sensor (turbo) connector.


e.

Reconnect the ECM connector.



OK

9.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)
a.

Replace the intake air temperature sensor (turbo) (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL).



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Allow the engine to soak for 1 to 2 hours.

HINT:
·

It is not necessary to allow the engine to soak if the engine is cold.

·

The engine cools faster if the hood is opened.




b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Engine and ECT / Data List / Coolant temp.


e.

Read the value.

NOTICE:

If the difference between "Coolant Temp" and the outside air temperature is 5°C (9°F) or higher, the heat from the engine affects the intake air temperature sensor, causing an incorrect value to be displayed. In this case, allow the engine to soak again.



f.

Enter the following menus: Engine and ECT / Data List / Intake Air and Intake Air Temp (Turbo).


g.

Read the value.

OK:

The difference between the displayed value and outside air temperature is below 15°C (27°F).




NEXT

END