Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P2453  Diesel Particulate Filter Pressure Sensor "A" Circuit Range/Performance  P245F  Diesel Particulate Filter Pressure Sensor "B" Circuit Range/Performance  


DESCRIPTION

HINT:
·

For more information on the differential pressure sensor assembly and Diesel Particulate Filter (DPF), refer to the following procedures (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).

·

If P2453 and/or P245F is present, refer to the DTC chart for DPF system (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).



U162832E02
4.438,1.208 4.25,1.438 false 4.594,1.115 4.729,1.365 false 4.406,1.156 4.219,1.229 false 5.323,3.042 5.083,2.552 5.083,2.552 5.135,2.552 false 1.313,2.167 0.802,2.917 false 2.75,2.5 2.885,2.917 false 1.688,1.052 1.688,1.208 false 1.302,0.708 2.167,0.896 0.865,0.188 10 false Exhaust Gas 2.917,0.708 3.26,0.875 0.344,0.167 10 false ECM 0.375,2.938 1.448,3.271 1.073,0.333 10 false DPF Catalytic Converter 2.344,2.938 3.635,3.271 1.292,0.333 10 false Differential Pressure Sensor 3.865,0.125 5.719,0.313 1.854,0.188 10 false Property of Output Voltage: 4.76,1.292 6.26,1.458 1.5,0.167 10 false Stores P2455 or P2461 5.146,2.479 6.646,2.646 1.5,0.167 10 false Stores P2454 or P2460 4.052,0.635 6.073,0.813 2.021,0.177 10 false Differential Pressure Voltage (V) 3.969,0.938 4.406,1.115 0.438,0.177 10 false 5.000 3.865,1.135 4.24,1.302 0.375,0.167 10 false 4.800 3.833,1.396 4.25,1.573 0.417,0.177 10 false 4.650 3.979,2.385 4.396,2.563 0.417,0.177 10 false 1.530 3.99,2.583 4.396,2.76 0.406,0.177 10 false 0.750 3.99,2.74 4.417,2.906 0.427,0.167 10 false 0.555 4,2.906 4.406,3.073 0.406,0.167 10 false 0.400 4.292,3.115 4.396,3.271 0.104,0.156 10 false 0 4.771,3.24 4.875,3.396 0.104,0.156 10 false 0 4.531,3.24 4.708,3.406 0.177,0.167 10 false -5 4.938,3.24 5.26,3.406 0.323,0.167 10 false 20.0 6.469,3.25 6.854,3.417 0.385,0.167 10 false 100.0 4.323,3.427 6.813,3.625 2.49,0.198 10 false Exhaust Gas Differential Pressure (kPa)

The two sensing chambers of the differential pressure sensor assembly are mounted to monitor the pressure before and after the DPF catalytic converter. The sensor itself is not located on the engine assembly in order to reduce the influence of vibration. The sensor is a semiconductor-type that is not influenced by exhaust gases.

The ECM compares the exhaust gas pressure before and after the DPF catalytic converter by monitoring the pressure using the upstream and downstream sensing chambers of the differential pressure sensor assembly. If the difference between the pressure before and after the catalytic converter exceeds a predetermined level, the ECM judges that the catalytic converter is clogged with particulate matter (PM). When the ECM judges that a partially clogged condition exists, the ECM begins to perform PM forced regeneration.

HINT:

If the vacuum hoses of the differential pressure sensor assembly are incorrectly connected (crossed), the ECM interprets this as an abnormal pressure difference, DTC P2453 or P245F is stored and the MIL illuminates.


P2453 (Bank 1), P245F (Bank 2)
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine is running at 4000 rpm with no load for 10 seconds or more. The output voltage from the differential pressure sensor assembly indicates a reversal of positive and negative pressure.
(1 trip detection logic)
·

Incorrect differential pressure sensor assembly hose routing

·

Differential pressure sensor assembly vacuum hose is clogged

·

Blockage in vacuum transmitting pipe sub-assembly

·

Differential pressure sensor assembly

·

ECM



Related Data List
DTC No. Data List
P2453 DPF Differential Pressure
P245F DPF Differential Pressure #2

HINT:
·

DTC P2454, P2455, P2460 or DTC P2461 will be stored if there is an open or short malfunction in the differential pressure sensor assembly circuit.

·

After confirming DTC P2453 or P245F, check the differential pressure in "Engine and ECT / Data List / DPF Differential Pressure and DPF Differential Pressure #2" using the GTS.


Reference:
Condition Differential Pressure Output Sensor Condition
Engine switch on (IG) Approximately 0 kPa Normal
Always -5 kPa or less or higher than 99 kPa Open or short circuit
4000 rpm (No engine load) Negative output Incorrect hose routing


MONITOR DESCRIPTION

In order to detect abnormality in the differential pressure sensor assembly, the ECM always monitors the output voltage from the sensor. When the sensor output voltage is a reversal of positive and negative pressure, the ECM interprets this as an incorrect vacuum hose arrangement of the sensor, or determines that the vacuum hoses are clogged, and illuminates the MIL.

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P2453 OR P245F)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
P2453 or P245F is output A
P2453 or P245F and other DTCs are output B

HINT:

If codes other than P2453 or P245F are output, perform troubleshooting for those DTCs first.




A

2.CHECK CONNECTION OF VACUUM HOSE (DIFFERENTIAL PRESSURE SENSOR - VACUUM TRANSMITTING PIPE)

B

2.CHECK CONNECTION OF VACUUM HOSE (DIFFERENTIAL PRESSURE SENSOR - VACUUM TRANSMITTING PIPE)
a.

Check if the vacuum hose routing between the differential pressure sensor assembly and vacuum transmitting pipe is correct (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>DIFFERENTIAL PRESSURE SENSOR(for DPF)>INSTALLATION).


b.

Check that there is no exhaust gas leakage between the differential pressure sensor assembly and vacuum transmitting pipe.



OK

3.CHECK BLOCKAGE OF VACUUM HOSE AND TRANSMITTING PIPE

NG

5.CORRECT TO NORMAL CONNECTION
3.CHECK BLOCKAGE OF VACUUM HOSE AND TRANSMITTING PIPE
CAUTION:

Be careful of being burned by exhaust gases during the following inspection.


a.

Disconnect the vacuum hoses (both upstream and downstream) from the differential pressure sensor assembly.


b.

Start the engine.


c.

Check if there are exhaust gas pulsations from both vacuum hoses during idling.

OK:

Exhaust gas pulsation exists.




OK

4.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE AND DPF DIFFERENTIAL PRESSURE #2)

NG

6.REPLACE CLOGGED PARTS
4.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE AND DPF DIFFERENTIAL PRESSURE #2)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure and DPF Differential Pressure #2.


d.

Check that the differential pressure is as specified below.

Result
Condition Differential Pressure Output Sensor Condition
Engine switch on (IG) Approximately 0 kPa Normal



OK

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

7.REPLACE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY
5.CORRECT TO NORMAL CONNECTION

NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE CLOGGED PARTS

NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPLACE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY

When DTC P2453 is output:

·

Replace the differential pressure sensor assembly (for bank 1) (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>DIFFERENTIAL PRESSURE SENSOR(for DPF)>REMOVAL).


When DTC P245F is output:

·

Replace the differential pressure sensor assembly (for bank 2) (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>DIFFERENTIAL PRESSURE SENSOR(for DPF)>REMOVAL).



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Turn the engine off for 30 seconds or more.


e.

Turn the engine switch on (IG) and turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure and DPF Differential Pressure #2.


g.

Check that the differential pressure is as specified below.

HINT:
·

As long as the pipe connections are correct, the displayed pressure will not be vacuum pressure.

·

For reference result of real-vehicle check is as shown in the table below:

Condition DPF Differential Pressure
DPF Differential Pressure #2
4000 rpm without load after warming up engine 0.2 kPa or more




h.

Start the engine.


i.

Engine is running at 4000 rpm with no load for 10 seconds or more.


j.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Engine and ECT / Utility / All Readiness.


ii.

Input DTC P2453 or P245F.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, run the engine at 4000 rpm with no load for 10 seconds or more.




NEXT

END