Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P2454  Diesel Particulate Filter Pressure Sensor "A" Circuit Low  P2455  Diesel Particulate Filter Pressure Sensor "A" Circuit High  P2460  Diesel Particulate Filter Pressure Sensor "B" Circuit Low  P2461  Diesel Particulate Filter Pressure Sensor "B" Circuit High  


DESCRIPTION

HINT:
·

For more information on the differential pressure sensor assembly and Diesel Particulate Filter (DPF), refer to the following procedures (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).

·

If P2454 P2455, P2460 or P2461 is present, refer to the DTC chart for DPF system (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).



U162832E02
4.438,1.208 4.25,1.438 false 4.594,1.115 4.729,1.365 false 4.406,1.156 4.219,1.229 false 5.323,3.042 5.083,2.552 5.083,2.552 5.135,2.552 false 1.313,2.167 0.802,2.917 false 2.75,2.5 2.885,2.917 false 1.688,1.052 1.688,1.208 false 1.302,0.708 2.167,0.896 0.865,0.188 10 false Exhaust Gas 2.917,0.708 3.26,0.875 0.344,0.167 10 false ECM 0.375,2.938 1.448,3.271 1.073,0.333 10 false DPF Catalytic Converter 2.344,2.938 3.635,3.271 1.292,0.333 10 false Differential Pressure Sensor 3.865,0.125 5.719,0.313 1.854,0.188 10 false Property of Output Voltage: 4.76,1.292 6.26,1.458 1.5,0.167 10 false Stores P2455 or P2461 5.146,2.479 6.646,2.646 1.5,0.167 10 false Stores P2454 or P2460 4.052,0.635 6.073,0.813 2.021,0.177 10 false Differential Pressure Voltage (V) 3.969,0.938 4.406,1.115 0.438,0.177 10 false 5.000 3.865,1.135 4.24,1.302 0.375,0.167 10 false 4.800 3.833,1.396 4.25,1.573 0.417,0.177 10 false 4.650 3.979,2.385 4.396,2.563 0.417,0.177 10 false 1.530 3.99,2.583 4.396,2.76 0.406,0.177 10 false 0.750 3.99,2.74 4.417,2.906 0.427,0.167 10 false 0.555 4,2.906 4.406,3.073 0.406,0.167 10 false 0.400 4.292,3.115 4.396,3.271 0.104,0.156 10 false 0 4.771,3.24 4.875,3.396 0.104,0.156 10 false 0 4.531,3.24 4.708,3.406 0.177,0.167 10 false -5 4.938,3.24 5.26,3.406 0.323,0.167 10 false 20.0 6.469,3.25 6.854,3.417 0.385,0.167 10 false 100.0 4.323,3.427 6.813,3.625 2.49,0.198 10 false Exhaust Gas Differential Pressure (kPa)

The two sensing chambers of the differential pressure sensor assembly are mounted to monitor the pressure before and after the DPF catalytic converter. The sensor itself is not located on the engine assembly in order to reduce the influence of vibration.

The ECM compares the exhaust gas pressure before and after the DPF catalytic converter by monitoring the pressure using the upstream and downstream sensing chambers of the differential pressure sensor assembly. If the difference in pressure exceeds a predetermined level, the ECM judges that the catalytic converter is clogged with particulate matter (PM). When the ECM judges that a partially clogged condition exists, the ECM begins to perform PM forced regeneration.

When the output voltage of the sensor deviates from the normal operating range, the ECM interprets this as a malfunction of the sensor circuit, and sets DTC P2454 P2455, P2460 or P2461, and illuminates the MIL.

HINT:

If the vacuum hoses of the differential pressure sensor assembly are incorrectly connected (crossed), the ECM interprets this as an abnormal pressure difference, DTC P2453 or P245F is stored and the MIL illuminates.


P2454 (Bank 1), P2460 (Bank 2)
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 5 seconds The differential pressure sensor assembly output voltage is below 0.4 V for 3 seconds or more.
(1 trip detection logic)
·

Open or short in differential pressure sensor assembly circuit

·

Incorrect differential pressure sensor assembly hose routing

·

Differential pressure sensor assembly

·

ECM



P2455 (Bank 1), P2461 (Bank 2)
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 5 seconds The differential pressure sensor assembly output voltage is higher than 4.8 V for 3 seconds or more.
(1 trip detection logic)
·

Open or short in differential pressure sensor assembly circuit

·

Incorrect differential pressure sensor assembly hose routing

·

Differential pressure sensor Assembly

·

ECM



Related Data List
DTC No. Data List
P2454
P2455
DPF Differential Pressure
P2460
P2461
DPF Differential Pressure #2

HINT:
·

DTC P2453 or P245F will be stored if there is incorrect vacuum hose routing to the differential pressure sensor assembly.

·

After confirming DTC P2454 P2455, P2460 or P2461, check the differential pressure in the "Engine and ECT / Data List / DPF Differential Pressure and DPF Differential Pressure #2" menu using the GTS.


Reference:
Condition Differential Pressure Output Sensor Condition
Engine switch on (IG) Approximately 0 kPa Normal
Always -5 kPa or less or higher than 99 kPa Open or short circuit
4000 rpm (No engine load) Negative output Incorrect hose routing


MONITOR DESCRIPTION

In order to detect abnormality in the differential pressure sensor assembly, the ECM always monitors the output voltage from the sensor. When the sensor output voltage deviates from the normal operating range (between 0.4 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction in the sensor circuit and illuminates the MIL.

WIRING DIAGRAM

A165736E14
2.01,1.135 2.281,1.344 0.271,0.208 10 false VC 1.938,1.469 2.292,1.677 0.354,0.208 10 false PEX 2.031,1.823 2.313,2 0.281,0.177 10 false E2 5.26,1.146 5.688,1.344 0.427,0.198 10 false VC 5.26,1.458 5.656,1.656 0.396,0.198 10 false PEX 5.26,1.823 5.74,2.021 0.479,0.198 10 false E2 2.354,1.896 2.542,2.083 0.188,0.188 10 false 1 2.365,1.229 2.552,1.417 0.188,0.188 10 false 3 2.365,1.563 2.552,1.75 0.188,0.188 10 false 2 4.927,1.229 5.219,1.417 0.292,0.188 10 false 91 4.938,1.563 5.167,1.75 0.229,0.188 10 false 69 5.26,3.635 5.719,3.833 0.458,0.198 10 false PEX2 4.917,3.719 5.208,3.906 0.292,0.188 10 false 70 4.938,1.927 5.208,2.115 0.271,0.188 10 false 92 1.073,2.135 1.427,2.323 0.354,0.188 10 false N16 1.073,2.323 3.479,2.677 2.406,0.354 10 false Differential Pressure Sensor Assembly (for Bank 1) 2.01,3.26 2.281,3.458 0.271,0.198 10 false VC 1.865,3.594 2.281,3.792 0.417,0.198 10 false PEX2 2.052,3.958 2.281,4.156 0.229,0.198 10 false E2 2.365,4.052 2.552,4.24 0.188,0.188 10 false 1 2.365,3.375 2.552,3.563 0.188,0.188 10 false 3 2.365,3.719 2.552,3.906 0.188,0.188 10 false 2 1,4.302 1.427,4.542 0.427,0.24 10 false C157 1,4.49 3.417,4.906 2.417,0.417 10 false Differential Pressure Sensor Assembly (for Bank 2) 5.552,4.646 6.552,4.875 1,0.229 10 false C45*1, C46*2 5.563,4.823 5.927,5 0.365,0.177 10 false ECM 3.75,4.948 4.75,5.177 1,0.229 10 false *1: for LHD 3.75,5.26 4.75,5.49 1,0.229 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK WIRE HARNESS (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY - ECM)
a.

Disconnect the differential pressure sensor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
N16-2 (PEX) - C45-69 (PEX) Always Below 1 Ω
N16-3 (VC) - C45-91 (VC) Always Below 1 Ω
N16-1 (E2) - C45-92 (E2) Always Below 1 Ω
C157-2 (PE2X) - C45-70 (PEX2) Always Below 1 Ω
C157-3 (VC) - C45-91 (VC) Always Below 1 Ω
C157-1 (E2) - C45-92 (E2) Always Below 1 Ω
N16-2 (PEX) or C45-69 (PEX) - Body ground Always 10 kΩ or higher
N16-3 (VC) or C45-91 (VC) - Body ground Always 10 kΩ or higher
C157-2 (PE2X) or C45-70 (PEX2) - Body ground Always 10 kΩ or higher
C157-3 (VC) or C45-91 (VC) - Body ground Always 10 kΩ or higher


Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
N16-2 (PEX) - C46-69 (PEX) Always Below 1 Ω
N16-3 (VC) - C46-91 (VC) Always Below 1 Ω
N16-1 (E2) - C46-92 (E2) Always Below 1 Ω
C157-2 (PE2X) - C46-70 (PEX2) Always Below 1 Ω
C157-3 (VC) - C46-91 (VC) Always Below 1 Ω
C157-1 (E2) - C46-92 (E2) Always Below 1 Ω
N16-2 (PEX) or C46-69 (PEX) - Body ground Always 10 kΩ or higher
N16-3 (VC) or C46-91 (VC) - Body ground Always 10 kΩ or higher
C157-2 (PE2X) or C46-70 (PEX2) - Body ground Always 10 kΩ or higher
C157-3 (VC) or C46-91 (VC) - Body ground Always 10 kΩ or higher



d.

Reconnect the differential pressure sensor assembly connector.


e.

Reconnect the ECM connector.



OK

2.CHECK TERMINAL VOLTAGE (VC)

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK TERMINAL VOLTAGE (VC)
a.
U163296E01
0.192,0.113 0.439,0.270 0.247,0.157 10 *a 2.409,1.66 2.667,1.823 0.258,0.163 10 VC 1.971,1.239 2.409,1.66 false 0.271,1.524 0.701,1.687 0.430,0.163 10 C157 0.828,1.526 1.075,1.683 0.247,0.157 10 *B 0.306,0.848 0.606,1.011 0.300,0.163 10 N16 0.811,0.85 1.058,1.007 0.247,0.157 10 *A

Disconnect the differential pressure sensor assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N16-3 (VC) - Body ground Engine switch on (IG) 4.5 to 5.5 V
C157-3 (VC) - Body ground Engine switch on (IG) 4.5 to 5.5 V


Text in Illustration
*A for Bank 1
*B for Bank 2
*a Front view of wire harness connector
(to Differential Pressure Sensor Assembly)


c.

Reconnect the differential pressure sensor assembly connector.



OK

3.REPLACE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY

NG

4.REPLACE ECM
3.REPLACE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY

When DTC P2454 or P2455 is output:

·

Replace the differential pressure sensor assembly (for bank 1) (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>DIFFERENTIAL PRESSURE SENSOR(for DPF)>REMOVAL).


When DTC P2460 or P2461 is output:

·

Replace the differential pressure sensor assembly (for bank 2) (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>DIFFERENTIAL PRESSURE SENSOR(for DPF)>REMOVAL).



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPLACE ECM

NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch on (IG) and wait for 5 seconds.


d.

Enter the following menus: Engine and ECT / Trouble Codes.


e.

Confirm that the DTC is not output again.



NEXT

END