Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P244B  Diesel Particulate Filter Differential Pressure Too High  P2465  Particulate Filter Differential Pressure Too High Bank 2  


DESCRIPTION

Refer to DTC P244C (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P244C).

P244B (Bank 1), P2465 (Bank 2)
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine is running at 4000 rpm with no load for 10 seconds or more. While driving, Catalyst Differential Pressure becomes more than 0.45 for 3 seconds.
(1 trip detection logic)
·

Front exhaust pipe assembly (for bank 1 DPF catalytic converter)

·

Front No. 2 exhaust pipe assembly (for bank 2 DPF catalytic converter)

·

Differential pressure sensor assembly (for bank 1)

·

Differential pressure sensor assembly (for bank 2)


Common Inspection Item:
·

Fuel injection system

·

Intake/exhaust system

·

After treatment control system



Related Data List
DTC No. Data List
P244B
·

DPF Differential Pressure

·

Catalyst Differential Press

·

Exhaust Fuel Addition FB


P2465
·

DPF Differential Pressure #2

·

Catalyst Differential Press #2

·

Exhaust Fuel Addition FB #2



MONITOR DESCRIPTION

The ECM compares pressure upstream and downstream of the DPF catalyst converter to monitor the differential pressure. If the differential pressure is large, the ECM determines that the DPF catalyst converter is contaminated or has deteriorated and illuminates the MIL.

A275258E02
3.073,3.375 3.271,3.375 3.271,3.375 4.01,1.563 true 5.042,1.01 5.563,0.281 true 5.563,0.281 5.74,0.281 false 5.958,2.427 5.771,2.427 5.771,2.427 5.323,2.208 true 1.51,3.313 3.031,3.594 1.521,0.281 10 false Stores P244B or P2465 3.542,2.969 4,3.198 0.458,0.229 10 false MAF 0.156,0.146 2.313,0.375 2.156,0.229 10 false Differential Pressure Malfunction: 0.25,1.656 1.333,2.073 1.083,0.417 10 false DPF Differential Pressure 5.813,0.198 7.01,0.427 1.198,0.229 10 false Clogged with PM 5.885,1.417 7.125,1.938 1.24,0.521 10 false PM amount of DPF catalyst converter increases 6.031,2.344 7.052,3.042 1.021,0.698 10 false No PM in DPF catalyst converter 1.115,0.979 1.5,1.208 0.385,0.229 10 false High 5.594,2.979 5.979,3.208 0.385,0.229 10 false High 1.125,2.656 1.51,2.885 0.385,0.229 10 false Low 1.573,2.938 1.958,3.167 0.385,0.229 10 false Low

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTC (RECORD STORED DTC AND FREEZE FRAME DATA)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Trouble Codes.


d.

Record the stored DTC and freeze frame data.


e.

Check Exhaust Fuel Addition FB, Exhaust Fuel Addition FB #2, Catalyst Differential Press and Catalyst Differential Press #2 in the freeze frame data.

HINT:
·

When the Exhaust Fuel Addition FB and Exhaust Fuel Addition FB #2 values are 1.45 or more, it indicates a high possibility of insufficient temperature increase during PM forced regeneration.

·

When the Catalyst Differential Press and Catalyst Differential Press #2 values are 0.45 or more, it indicates a high possibility that the DPF catalyst is clogged.





NEXT

2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P244B OR P2465)
2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P244B OR P2465)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
P244B or P2465 is output A
P244B or P2465 is output at the same time as P2463*
Other relevant DTCs are output B

HINT:

*: When P244B or P2465 is output at the same time as P2463, perform this diagnostic procedure. When DTC P244B or P2465 is not output at the same time as P2463 is output, perform the diagnostic procedure for P244C or P244E (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P244C).




A

3.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)

B

9.GO TO DTC CHART
3.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Data List / DPF Differential Pressure and DPF Differential Pressure #2.


d.

Check the DPF Differential Pressure and DPF Differential Pressure #2 values from idle speed to unloaded maximum engine speed.

Result
Result Proceed to
DPF Differential Pressure and DPF Differential Pressure #2 increase as engine speed increases from idle speed A
Except above B

A241154E04
3.313,3.375 3.542,3.375 3.542,3.375 3.719,3.875 false 4.25,4.281 4.125,4.281 false 4.125,4.281 3.854,3.979 false 4.146,4.927 4.042,4.927 4.042,4.927 3.833,4.76 false 0.469,1.479 1.74,1.865 1.271,0.385 10 Engine Speed (rpm) 0.833,2.99 1.74,3.375 0.906,0.385 10 MAF (gm/sec) 0.688,4.115 1.698,4.521 1.01,0.406 10 DPF Differential Pressure (kPa) 4.198,4.854 4.323,5 0.125,0.146 10 A 1.771,1.875 1.875,2.156 0.104,0.281 10 0 1.781,3.24 1.885,3.521 0.104,0.281 10 0 1.792,4.615 1.896,4.896 0.104,0.281 10 0 0.677,0.854 1.948,1.24 1.271,0.385 10 Unloaded Maximum Engine Speed 2.385,3.281 3.344,3.521 0.958,0.24 10 Normal Piping 4.313,4.208 5.271,4.448 0.958,0.24 10 Clogged Piping 2.313,5.417 5.333,5.698 3.021,0.281 10 Negative pressure occurs for approx. 1 second.

HINT:

If DPF Differential Pressure and DPF Differential Pressure #2 indicate negative pressure for approx. 1 second as shown in the illustration (A) when the engine speed increases, the differential pressure sensor piping of the DPF catalyst may be clogged.

·

There are cases where the bank 1 side will display an extremely large or small value depending on the vehicle. In these cases, the value needs to be converted.

·

Subtract 327.68 kPa for positive values.

·

Add 327.68 kPa for negative values.

·

Example 1: Displayed value 327.35 - 327.68 = -0.33 kPa

·

Example 2: Displayed value -327.63 + 327.68 = -0.05 kPa





B

4.CLEAN OR REPLACE VACUUM TRANSMITTING HOSE

A

5.CHECK FOR BLACK SMOKE
4.CLEAN OR REPLACE VACUUM TRANSMITTING HOSE
a.

Even though it has been determined that the vacuum transmitting hose needs to be repaired or cleaned, make sure to perform all diagnostic procedures for DTC P244B or P2465 before repairing or cleaning it.



NEXT

5.CHECK FOR BLACK SMOKE
5.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it [A].


d.

Repeat the above procedure [A] 10 times [B].


e.

Check for black smoke emission during procedures [A] and [B].

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.




OK

6.READ VALUE USING GTS (CATALYST DIFFERENTIAL PRESS)

NG

8.REPLACE EXHAUST PIPE ASSEMBLY (DPF CATALYST CONVERTER)
6.READ VALUE USING GTS (CATALYST DIFFERENTIAL PRESS)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Catalyst Differential Press and Catalyst Differential Press #2.


d.

Check the value of Catalyst Differential Press and Catalyst Differential Press #2 at 4000 rpm without load.

Result
Result Proceed to
Catalyst Differential Press or Catalyst Differential Press #2 is more than 0.45 A
Except above B



B

7.PERFORM PM FORCED REGENERATION

A

8.REPLACE EXHAUST PIPE ASSEMBLY (DPF CATALYST CONVERTER)
7.PERFORM PM FORCED REGENERATION
a.

Remove the EFI MAIN fuse or disconnect the cable from the battery terminal for 60 seconds or more, and then reinstall the EFI MAIN fuse or reconnect the cable to the battery terminal.

HINT:
·

The amount of built up particulate matter recorded by the ECM cannot be initialized by the GTS.

·

If the amount of built up particulate matter recorded by the ECM is not initialized, PM forced regeneration cannot be performed using the GTS.




b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.



e.

Start the engine.


f.

Enter the following menus: Engine and ECT / Data List / Coolant Temp.


g.

Warm up the engine (engine coolant temperature is 70°C (158°F) or higher).



i.

Turn the ignition switch off.



OK

END

NG

10.CHECK FUEL INJECTION SYSTEM
8.REPLACE EXHAUST PIPE ASSEMBLY (DPF CATALYST CONVERTER)

Even though it has been determined that the DPF catalyst converter needs to be replaced, make sure to perform all diagnostic procedures for DTC P244B or P2465 before replacing it.


NEXT

10.CHECK FUEL INJECTION SYSTEM
9.GO TO DTC CHART

NEXT

10.CHECK FUEL INJECTION SYSTEM
10.CHECK FUEL INJECTION SYSTEM

NEXT

11.CHECK INTAKE / EXHAUST SYSTEM
11.CHECK INTAKE / EXHAUST SYSTEM

NEXT

12.CHECK AFTER TREATMENT CONTROL SYSTEM
12.CHECK AFTER TREATMENT CONTROL SYSTEM

NEXT

13.REPAIR OR REPLACE MALFUNCTIONING PARTS
13.REPAIR OR REPLACE MALFUNCTIONING PARTS
HINT:
·

Repair, replace or clean the following items only when it has been determined necessary based on diagnosis for DTC P244B or P2465.

·

Replace the DPF catalytic converter for bank 1 and bank 2 at the same time.



When DTC P244B is output:

·

Clean and/or repair the hoses of the differential pressure sensor (for bank 1).

·

Replace the exhaust pipe assembly (for bank 1 DPF catalytic converter) (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST PIPE(w/ DPF)>REMOVAL).

·

Replace the front No. 2 exhaust pipe assembly (for bank 2 DPF catalytic converter) (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST PIPE(w/ DPF)>REMOVAL).


When DTC P2465 is output:

·

Clean and/or repair the hoses of the differential pressure sensor (for bank 2).

·

Replace the exhaust pipe assembly (for bank 1 DPF catalytic converter) (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST PIPE(w/ DPF)>REMOVAL).

·

Replace the front No. 2 exhaust pipe assembly (for bank 2 DPF catalytic converter) (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST PIPE(w/ DPF)>REMOVAL).



NEXT

14.CATALYST RECORD CLEAR
14.CATALYST RECORD CLEAR

NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.





NEXT

END