Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P20CD  Open in Exhaust Aftertreatment Fuel Injector "A" Control Circuit  P20D3  Open in Exhaust Aftertreatment Fuel Injector "B" Control Circuit  


DESCRIPTION

A268071E03
0.601,2.502 2.423,2.695 1.823,0.193 10 Turbocharger Sub-assembly 0.059,1.615 0.909,1.817 0.850,0.202 10 Exhaust Gas 1.981,0.132 3.384,0.543 1.404,0.411 10 Exhaust Fuel Addition Injector Assembly 3.702,0.286 5.881,0.600 2.179,0.313 10 Exhaust Gas Temperature Sensor (B1S1, B2S1) 3.649,1.541 6.184,2.055 2.534,0.514 10 No. 2 Exhaust Gas Temperature Sensor (B1S2), No. 3 Exhaust Gas Temperature Sensor (B2S2) 3.529,3.67 6.030,4.060 2.501,0.390 10 No. 4 Exhaust Gas Temperature Sensor (B1S3, B2S3) 6.445,2.535 6.795,2.746 0.350,0.211 10 ECM 0.414,3.194 2.125,3.359 1.711,0.165 10 DPF Catalytic Converter 0.764,4.426 2.142,4.610 1.378,0.184 10 Air Fuel Ratio Sensor 1.257,1.216 1.789,0.2 1.789,0.2 1.929,0.2 false 2.539,2.897 2.119,3.261 2.119,3.261 2.02,3.261 false 2.364,3.787 0.907,4.242 0.907,4.242 0.907,4.347 false 2.968,3.343 3.351,3.763 3.351,3.763 3.473,3.763 false 2.993,2.302 3.534,0.361 3.534,0.361 3.639,0.361 false 3.098,2.729 3.492,1.629 3.492,1.629 3.59,1.629 false

The exhaust fuel addition injector assembly is mounted on the exhaust port of the cylinder head, and low pressure fuel is supplied to the injector assembly by the feed pump in the fuel supply pump assembly. This injector adds fuel according to a control signal from the ECM.

This injector assembly is used for two different controls: PM forced regeneration and PM reduction.

During PM forced regeneration, the injector adds fuel to raise the catalyst temperature.

In the other control, the injector helps the air-fuel ratio become rich. As a result, PM in the exhaust gas will be reduced in response to the rich air-fuel ratio.

HINT:
·

For more information on the exhaust fuel addition injector assembly and DPF, refer to the following procedures (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).

·

If P20CD or P20D3 is present, refer to the DTC table for Diesel Particulate Filter System (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).



P20CD (Bank 1), P20D3 (Bank 2)
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 3 seconds With the exhaust fuel addition injector off, the FIVO or FIVO2 output is high for 3 seconds.
(1 trip detection logic)
·

Open in exhaust fuel addition injector assembly circuit

·

Exhaust fuel addition injector assembly

·

ECM



HINT:

DTC P200C, P200D, P20CF or P20D5 will be present if there is an open malfunction in the exhaust fuel addition injector circuit.


MONITOR DESCRIPTION

In order to detect abnormality in the fuel addition injector assembly, an internal CPU of the ECM monitors injection command (FIV and FIV2) signals and injection confirmation (FIVO and FIVO2) signals. The FIV and FIV2 signals are sent from the CPU to the exhaust fuel addition injector assembly via a drive circuit inside the ECM. The FIVO and FIVO2 signals, which are originally output current from the internal drive circuit of the ECM, are transmitted to the CPU via a monitor circuit. By receiving the FIVO and FIVO2 signals, the ECM judges that current has been applied to the exhaust fuel addition injector assembly.

These DTCs will be set if the ECM judges that the number of signals of the FIV and FIV2, and the FIVO and FIVO2 are inconsistent.

A265674E06
2.625,0.323 2.969,0.5 0.344,0.177 10 false ECM 1.229,0.906 1.573,1.125 0.344,0.219 10 false CPU 1.385,1.583 1.813,1.75 0.427,0.167 10 false FIVO 1.49,2.469 1.802,2.646 0.313,0.177 10 false FIV 3.219,1.469 4.25,1.646 1.031,0.177 10 false Monitor Circuit 3.188,2.344 4.292,2.521 1.104,0.177 10 false Command Circuit 5.458,1.063 6.969,1.448 1.51,0.385 10 false to Fuel Addition Injector Assembly 0.146,0.073 0.917,0.25 0.771,0.177 10 false for Bank 1

WIRING DIAGRAM

A275253E01
3.064,1.194 5.609,1.530 2.545,0.336 10 Exhaust Fuel Addition Injector Assembly (for Bank 1) 3.418,1.01 3.823,1.194 0.406,0.184 10 C160 5.09,3.835 5.394,4.033 0.304,0.198 10 A38 5.417,3.831 5.721,4.028 0.304,0.198 10 A52 5.072,3.653 5.388,3.808 0.316,0.156 10 44*1 5.385,3.653 5.701,3.808 0.316,0.156 10 44*2 5.081,0.699 5.385,0.897 0.304,0.198 10 C45 5.408,0.695 5.712,0.892 0.304,0.198 10 C46 5.074,2.432 5.379,2.629 0.304,0.198 10 C45 5.401,2.427 5.705,2.625 0.304,0.198 10 C46 5.091,0.533 5.406,0.689 0.316,0.156 10 83*1 5.404,0.533 5.719,0.689 0.316,0.156 10 83*2 5.067,2.261 5.383,2.417 0.316,0.156 10 84*1 5.38,2.261 5.696,2.417 0.316,0.156 10 84*2 5.817,0.682 6.070,0.845 0.253,0.163 10 FIV 5.789,2.416 6.167,2.579 0.378,0.163 10 FIV2 5.773,3.717 6.182,3.880 0.408,0.163 10 MREL 4.274,0.576 4.527,0.738 0.253,0.163 10 FIV 3.788,0.577 4.036,0.766 0.248,0.188 10 +B 3.55,0.563 3.659,0.710 0.110,0.147 10 2 4.624,0.563 4.733,0.710 0.110,0.147 10 1 2.036,0.696 2.252,0.871 0.215,0.175 10 1A 2.036,1.047 2.252,1.222 0.215,0.175 10 1A 0.89,2.023 1.105,2.198 0.215,0.175 10 1A 0.271,2.037 0.487,2.212 0.215,0.175 10 1C 1.168,2.027 1.277,2.174 0.110,0.147 10 3 0.108,2.025 0.217,2.172 0.110,0.147 10 1 2.083,1.243 2.193,1.389 0.110,0.147 10 2 2.083,0.524 2.193,0.670 0.110,0.147 10 4 0.397,0.822 1.164,0.997 0.767,0.174 10 EFI MAIN 2 1.154,1.402 1.921,1.576 0.767,0.174 10 EFI MAIN 2 2.602,0.855 3.270,1.026 0.669,0.171 10 EFI NO. 2 1.065,2.252 2.205,2.405 1.140,0.154 10 Integration Relay 0.617,3.69 1.078,3.860 0.461,0.170 10 Battery 3.307,4.068 4.118,4.231 0.811,0.163 10 *1: for LHD 3.307,4.402 4.118,4.565 0.811,0.163 10 *2: for RHD 6.179,4.372 6.562,4.560 0.383,0.188 10 ECM 3.592,2.329 3.701,2.475 0.110,0.147 10 2 4.666,2.329 4.775,2.475 0.110,0.147 10 1 2.602,2.592 3.270,2.763 0.669,0.171 10 EFI NO. 3 4.239,2.313 4.582,2.476 0.343,0.163 10 FIV2 3.809,2.315 4.057,2.503 0.248,0.188 10 +B 3.029,2.854 5.574,3.190 2.545,0.336 10 Exhaust Fuel Addition Injector Assembly (for Bank 2) 3.383,2.671 3.788,2.854 0.406,0.184 10 C161

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT EXHAUST FUEL ADDITION INJECTOR ASSEMBLY (RESISTANCE)
a.

Inspect the exhaust fuel addition injector assembly (for bank 1 or bank 2) (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EXHAUST FUEL ADDITION INJECTOR (for DPF)>INSPECTION).



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE)

NG

5.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
2.CHECK TERMINAL VOLTAGE (POWER SOURCE)
a.
U163305E02
0.438,0.24 0.656,0.427 0.219,0.188 10 false *a 0.313,0.844 0.719,1.031 0.406,0.188 10 false C160 0.781,0.844 1,1.031 0.219,0.188 10 false *A 0.323,1.396 0.76,1.583 0.438,0.188 10 false C161 0.792,1.375 1.01,1.563 0.219,0.188 10 false *B

Disconnect the exhaust fuel addition injector assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C160-2 - Body ground Engine switch on (IG) 11 to 14 V
C161-2 - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*A for Bank 1
*B for Bank 2
*a Front view of wire harness connector
(to Exhaust Fuel Addition Injector Assembly)


c.

Reconnect the exhaust fuel addition injector assembly connector.



OK

3.CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - ECM)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - ECM)
a.

Disconnect the exhaust fuel addition injector assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C160-1 - C45-83 (FIV) Always Below 1 Ω
C161-1 - C45-84 (FIV2) Always Below 1 Ω
C160-1 or C45-83 (FIV) - Body ground Always 10 kΩ or higher
C161-1 or C45-84 (FIV2) - Body ground Always 10 kΩ or higher


Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C160-1 - C46-83 (FIV) Always Below 1 Ω
C161-1 - C46-84 (FIV2) Always Below 1 Ω
C160-1 or C46-83 (FIV) - Body ground Always 10 kΩ or higher
C161-1 or C46-84 (FIV2) - Body ground Always 10 kΩ or higher



d.

Reconnect the exhaust fuel addition injector assembly connector.


e.

Reconnect the ECM connector.



OK

4.REPLACE ECM

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
·

When DTC P20CD is output:

Replace the exhaust fuel addition injector assembly (for bank 1) (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EXHAUST FUEL ADDITION INJECTOR (for DPF)>REMOVAL).


·

When DTC P20D3 is output:

Replace the exhaust fuel addition injector assembly (for bank 2) (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EXHAUST FUEL ADDITION INJECTOR (for DPF)>REMOVAL).



NEXT

6.PERFORM PM FORCED REGENERATION
6.PERFORM PM FORCED REGENERATION
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Perform PM forced regeneration (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).

HINT:

When the exhaust fuel addition injector assembly is replaced, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.




NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
HINT:

If the voltage at the exhaust fuel addition injector assembly connector is not 11 to 14 V, repair or replace the harness and connector between the exhaust fuel addition injector assembly and EFI MAIN 2 relay (including the EFI No. 2 and EFI No. 3 fuses).


a.

Repair or replace the harness or connector.



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Drive the vehicle for 20 minutes.

HINT:

The exhaust gas temperature increases to 250°C (482°F) or higher after driving the vehicle for 20 minutes.



d.

Enter the following menus: Engine and ECT / Trouble Codes.


e.

Confirm that the DTC is not output again.



NEXT

END