Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P244C  Exhaust Temperature Too Low for Particulate Filter Regeneration Bank 1  P244E  Exhaust Temperature Too Low for Particulate Filter Regeneration Bank 2  P2458  Diesel Particulate Filter Regeneration Duration  P2463  Diesel Particulate Filter Restriction - Soot Accumulation  


DESCRIPTION

The DPF (Diesel Particulate Filter) is an emission control system which processes the particulate matter (PM) that is emitted from a diesel engine. The DPF catalyst converter has a porous ceramic structure which has a PM collecting function. The PM that is collected is continuously treated by oxidation due to catalytic action at high temperatures. However, however PM accumulation increases at low catalyst temperatures because the oxidation process slows down. The ECM performs PM forced regeneration so that the amount of accumulated PM does not exceed the threshold.

A254515E01
0.105,0.085 0.887,0.279 0.782,0.194 10 Reference: 3.546,1.122 4.435,1.277 0.889,0.155 10 Exhaust Gas 0.466,2.101 1.642,2.322 1.176,0.22 10 Oxidation Catalyst 2.279,2.232 3.321,2.443 1.042,0.211 10 DPF Catalyst 3.817,0.531 5.002,0.752 1.185,0.22 10 Oxidation Catalyst 5.414,2.11 6.303,2.264 0.889,0.155 10 Exhaust Gas 5.741,0.669 7.079,0.88 1.338,0.211 10 Enlarged Illustration 4.919,1.391 5.157,0.613 5.157,0.613 5.007,0.613 false 0.625,1.772 0.293,2.178 0.293,2.178 0.415,2.178 false 1.867,1.819 2.096,2.291 2.096,2.291 2.208,2.291 false

P244C (Bank 1), P244E (Bank 2)
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
PM forced regeneration During PM forced regeneration, catalyst temperature does not increase sufficiently for 3 minutes.
(1 trip detection logic)
·

Monolithic converter assembly RH (for bank 1 CCo catalytic converter)

·

Monolithic converter assembly LH (for bank 2 CCo catalytic converter)

·

Front exhaust pipe assembly (for bank 1 DPF catalytic converter)

·

Front No. 2 exhaust pipe assembly (for bank 2 DPF catalytic converter)

·

Exhaust fuel addition injector assembly

·

No. 2 exhaust gas temperature sensor (B1S2)

·

No. 3 exhaust gas temperature sensor (B2S2)

·

No. 4 exhaust gas temperature sensor (B1S3, B2S3)


Common Inspection Item:
·

Fuel injection system

·

Intake/exhaust system

·

After treatment control system



P2458
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
PM forced regeneration When PM forced regeneration is manually performed, PM forced regeneration does not finish even after 60 minutes or more elapse.
(1 trip detection logic)
·

Monolithic converter assembly RH (for bank 1 CCo catalytic converter)

·

Monolithic converter assembly LH (for bank 2 CCo catalytic converter)

·

Front exhaust pipe assembly (for bank 1 DPF catalytic converter)

·

Front No. 2 exhaust pipe assembly (for bank 2 DPF catalytic converter)

·

Exhaust fuel addition injector assembly

·

No. 2 exhaust gas temperature sensor (B1S2)

·

No. 3 exhaust gas temperature sensor (B2S2)

·

No. 4 exhaust gas temperature sensor (B1S3, B2S3)


Common Inspection Item:
·

Fuel injection system

·

Intake/exhaust system

·

After treatment control system



P2463
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
PM forced regeneration While driving, PM accumulation amount exceeds the limit.
(1 trip detection logic)
·

Monolithic converter assembly RH (for bank 1 CCo catalytic converter)

·

Monolithic converter assembly LH (for bank 2 CCo catalytic converter)

·

Front exhaust pipe assembly (for bank 1 DPF catalytic converter)

·

Front No. 2 exhaust pipe assembly (for bank 2 DPF catalytic converter)

·

Exhaust fuel addition injector assembly

·

No. 2 exhaust gas temperature sensor (B1S2)

·

No. 3 exhaust gas temperature sensor (B2S2)

·

No. 4 exhaust gas temperature sensor (B1S3, B2S3)

·

Differential pressure sensor assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/exhaust system

·

After treatment control system



HINT:

PM forced regeneration may be prohibited due to a fail-safe operation that is performed when another DTC is stored (including engine output limitation).


Related Data List
DTC No. Data List
P244C
P244E
P2458
P2463
·

Exhaust Fuel Addition FB

·

Exhaust Fuel Addition FB #2

·

Catalyst Differential Press

·

Catalyst Differential Press #2



MONITOR DESCRIPTION

The ECM monitors the differential pressure between the upstream and downstream of the DPF catalyst converter and also monitors exhaust gas temperature to detect a malfunction in the DPF catalyst converter.

Excessive PM accumulation:

The ECM monitors the PM Accumulation Ratio and when the accumulated PM volume in the DPF catalyst converter exceeds the limit, the ECM illuminates the MIL.


Abnormal catalyst temperature increase:

The ECM monitors exhaust gas temperature increase while the exhaust fuel addition injector assemblies adds fuel during PM forced regeneration. Exhaust gas temperature increases up to approximately 300 to 500°C (572 to 932°F) during PM forced regeneration. If the temperature does not increase even after a certain amount of time has elapsed, the ECM determines that the DPF catalyst converter is abnormal and illuminates the MIL.


Diesel particulate filter regeneration duration:

When PM forced regeneration is manually performed and PM forced generation does not finish even after 60 minutes or more elapse, the ECM determines that there is problem with the DPF catalyst converter and illuminates the MIL.

A208470E11
3.229,1.875 3.323,2.031 3.323,2.031 3.49,2.031 false 5.229,1.875 5.302,1.625 5.302,1.625 5.417,1.625 false 5.135,1.458 5.083,1.281 5.083,1.281 4.958,1.281 false 5.313,1.427 5.396,0.875 5.396,0.875 5.531,0.875 false 0.083,0.083 2.052,0.417 1.969,0.333 10 false Catalyst Activation Malfunction: (DPF not Activated) 0.896,0.938 2.76,1.302 1.865,0.365 10 false PM Forced Regeneration (Activation of Fuel Addition) 1.073,1.781 2.823,1.99 1.75,0.208 10 false Exhaust Gas Temperature 3.521,1.958 5.708,2.146 2.188,0.188 10 false About 150 to 300°C (302 to 572°F) 5.458,1.563 6.104,1.729 0.646,0.167 10 false Abnormal 4.49,1.208 4.969,1.375 0.479,0.167 10 false Normal 3.323,0.813 3.635,1 0.313,0.188 10 false Off 5.135,0.385 5.375,0.542 0.24,0.156 10 false On 5.563,0.802 7.063,1.146 1.5,0.344 10 false More than About 500°C (932°F) 4.24,2.438 4.594,2.594 0.354,0.156 10 false Time


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:
·

If DTC P244B, P244C, P244E, P2458, P2463 or P2465 is stored, the fail-safe controls the engine power output and PM forced regeneration is prohibited. In this case, PM forced regeneration can be performed after disconnecting the EFI MAIN fuse or battery terminal and waiting for 60 seconds or more before connecting it again.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ OUTPUT DTC (RECORD STORED DTC AND FREEZE FRAME DATA)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Engine and ECT / Trouble Codes.


e.

Record the stored DTC and freeze frame data.


f.

Check "Exhaust Fuel Addition FB", "Exhaust Fuel Addition FB #2", "Catalyst Differential Press" and "Catalyst Differential Press #2" in the freeze frame data.

HINT:
·

When the "Exhaust Fuel Addition FB" and "Exhaust Fuel Addition FB #2" values are 1.45 or more, it indicates a high possibility of insufficient temperature increase during PM regeneration control.

·

When the "Catalyst Differential Press" and "Catalyst Differential Press #2" values are 0.45 or more, it indicates a high possibility that DPF catalyst converter is clogged.





NEXT

2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P244C, P244E, P2458 AND P2463)
2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P244C, P244E, P2458 AND P2463)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
P244C, P244E, P2458 or P2463 is output A
P244B or P2465 is output at the same time as P2463* B
Only P2463 is output C
Other relevant DTCs are output D

HINT:
·

*: When P244B or P2465 is output at the same time as P2463, perform troubleshooting for P244B or P2465.

·

When DTC P1603, P1604 or P1608 is output in addition to P244C or P244E, perform troubleshooting for P1603, P1604 or P1608 first.





A

3.CHECK FOR BLACK SMOKE

B

C

7.CHECK FUEL INJECTION SYSTEM

D

4.GO TO DTC CHART
3.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it [A].


d.

Repeat the above procedure [A] 10 times [B].


e.

Check for black smoke emission during procedures [A] and [B].

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.




OK

5.CHECK FOR WHITE SMOKE (DURING PM FORCED REGENERATION)

NG

6.REPLACE EXHAUST PIPE ASSEMBLIES (DPF CATALYTIC CONVERTERS)
4.GO TO DTC CHART

NEXT

5.CHECK FOR WHITE SMOKE (DURING PM FORCED REGENERATION)
5.CHECK FOR WHITE SMOKE (DURING PM FORCED REGENERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Start the engine and warm it up until the engine coolant temperature reaches 60°C (140°F) or higher.



f.

Check if excessive white smoke occurs when "Exhaust Temperature B1S3" and "Exhaust Temperature B2S3" are 300°C (572°F) or more.

Result
Result Proceed to
Excessive smoke occurs during PM forced regeneration (Exhaust Temperature B1S3 and Exhaust Temperature B2S3 are 300°C (572°F)) A
Except above B

HINT:
·

When excessive white smoke occurs only during PM forced regeneration, the problem may be due to uncombusted fuel passing through due to the deterioration of the DPF catalyst converter.

·

When combustion control has a malfunction, deterioration or abnormality of driving performance can be felt despite PM forced regeneration being performed.





A

6.REPLACE EXHAUST PIPE ASSEMBLIES (DPF CATALYTIC CONVERTERS)

B

7.CHECK FUEL INJECTION SYSTEM
6.REPLACE EXHAUST PIPE ASSEMBLIES (DPF CATALYTIC CONVERTERS)
a.

Even though it has been determined that the exhaust pipe assemblies (DPF catalyst converters) need to be replaced, make sure to perform all diagnostic procedures for P244C, P244E, P2458 and P2463 before replacing them.

HINT:

These DTCs are stored because an excessive amount of PM has accumulated and resulted in abnormal combustion. It is necessary to diagnose the cause of abnormal PM accumulation and repair the problem. Therefore, do not perform replacement at this time.




NEXT

7.CHECK FUEL INJECTION SYSTEM
7.CHECK FUEL INJECTION SYSTEM

NEXT

8.CHECK INTAKE / EXHAUST SYSTEM
8.CHECK INTAKE / EXHAUST SYSTEM

NEXT

9.CHECK AFTER TREATMENT CONTROL SYSTEM
9.CHECK AFTER TREATMENT CONTROL SYSTEM

NEXT

10.REPAIR OR REPLACE MALFUNCTIONING PARTS
10.REPAIR OR REPLACE MALFUNCTIONING PARTS
a.

Determine the parts to replace according to the output DTCs.

Result
Result Items to be Replaced
P244C is output
·

Monolithic converter assembly RH (for bank 1 CCo catalytic converter)

·

Front exhaust pipe assembly (for bank 1 DPF catalytic converter)

·

Front No. 2 exhaust pipe assembly (for bank 2 DPF catalytic converter)


P244E is output
·

Monolithic converter assembly LH (for bank 2 CCo catalytic converter)

·

Front exhaust pipe assembly (for bank 1 DPF catalytic converter)

·

Front No. 2 exhaust pipe assembly (for bank 2 DPF catalytic converter)


P2458 is output
·

Monolithic converter assembly RH (for bank 1 CCo catalytic converter)

·

Monolithic converter assembly LH (for bank 2 CCo catalytic converter)

·

Front exhaust pipe assembly (for bank 1 DPF catalytic converter)

·

Front No. 2 exhaust pipe assembly (for bank 2 DPF catalytic converter)


P2463* is output
·

Monolithic converter assembly RH (for bank 1 CCo catalytic converter)

·

Monolithic converter assembly LH (for bank 2 CCo catalytic converter)

·

Front exhaust pipe assembly (for bank 1 DPF catalytic converter)

·

Front No. 2 exhaust pipe assembly (for bank 2 DPF catalytic converter)




HINT:
·

Replace the following items only when it has been determined necessary based on diagnosis for P244C, P244E, P2458 and P2463.

·

Replace the DPF catalytic converter for bank 1 and bank 2 at the same time.

·

*: During the after treatment control system inspection performed when DTC P2463 is output, if Catalyst Differential Press and Catalyst Differential Press #2 decrease to 0.45 or less after forced regeneration is performed and there are no melted or clogged areas found when visually inspecting the CCo catalytic converter and DPF catalytic converter, then do not perform catalytic converter replacement.



b.

Replace the front exhaust pipe assembly (for bank 1 DPF catalytic converter) (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST PIPE(w/ DPF)>REMOVAL).


c.

Replace the front No. 2 exhaust pipe assembly (for bank 2 DPF catalytic converter) (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST PIPE(w/ DPF)>REMOVAL).


d.

Replace the Monolithic converter assembly RH (for bank 1 CCo catalytic converter) (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST PIPE(w/ DPF)>REMOVAL).


e.

Replace the Monolithic converter assembly LH (for bank 2 CCo catalytic converter) (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST PIPE(w/ DPF)>REMOVAL).


f.

Repair or replace the malfunctioning part confirmed in the diagnosis of the fuel injection system, Intake/exhaust system and after treatment control system.



NEXT

11.CATALYST RECORD CLEAR
11.CATALYST RECORD CLEAR
a.

Perform the catalyst record clear (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

HINT:
·

If the DPF catalytic converter or CCo catalytic converter is replaced, perform "catalyst record clear".

·

If the DPF catalytic converter and CCo catalytic converter were not replaced, proceed to the next step.





NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Start the engine and warm it up until the engine coolant temperature reaches 60°C (140°F) or higher.




NEXT

END