Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052774 1GR-FE ENGINE CONTROL _0255001 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate the detection of vehicle malfunctions by the ECM. When the ignition switch is turned to ON, power is supplied to the MIL circuit and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually. When the ignition switch is first turned to ON, the MIL should be illuminated and should then turn off when the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A277872E01
3.791,1.276 4.127,1.445 0.336,0.170 10 MIL 4.695,1.191 5.032,1.360 0.336,0.170 10 CHK 0.289,1.107 1.254,1.273 0.965,0.166 10 from IG2 Relay 1.848,1.233 2.251,1.412 0.402,0.178 10 MET 1.799,0.986 1.936,1.142 0.137,0.156 10 1 2.111,0.986 2.249,1.142 0.137,0.156 10 2 2.538,0.938 2.735,1.094 0.198,0.156 10 18 5.757,1.212 5.954,1.368 0.198,0.156 10 24 6.017,1.003 6.215,1.159 0.198,0.156 10 W 2.817,1.192 3.098,1.348 0.281,0.156 10 IG+ 5.107,0.931 5.305,1.087 0.198,0.156 10 12 3.311,2.02 3.588,2.195 0.277,0.175 10 E8 3.311,2.168 4.581,2.343 1.270,0.175 10 Combination Meter 5.945,2.439 6.812,2.614 0.867,0.175 10 A38*1, A52*2 5.945,2.587 6.339,2.762 0.394,0.175 10 ECM 4.932,2.933 5.676,3.260 0.744,0.327 10 *1: for LHD *2: for RHD 5.093,1.107 5.294,1.252 0.201,0.145 10 E8 2.537,1.107 2.740,1.257 0.203,0.151 10 E7

PROCEDURE

1.CHECK WHETHER MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.

Result
Result Proceed to
MIL remains on A
MIL does not illuminate B



A

2.CHECK WHETHER MIL TURNS OFF

B

5.CHECK THAT MIL IS ILLUMINATED
2.CHECK WHETHER MIL TURNS OFF
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Check if DTCs have been stored (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR). If DTCs are output, write them down.



e.

Check that the MIL turns off.

OK:

MIL turns off.




OK

NG

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.




OK

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
E8-12 (CHK) or A38-24 (W) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
E8-12 (CHK) or A52-24 (W) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK THAT MIL IS ILLUMINATED
a.

Check if the MIL is illuminated when the ignition switch is turned to ON.

OK:

MIL illuminates.




OK

SYSTEM OK

NG

6.CHECK THAT ENGINE STARTS
6.CHECK THAT ENGINE STARTS
a.

Turn the ignition switch to ON.


b.

Start the engine.

Result
Result Proceed to
Engine starts A
Engine does not start* B

HINT:

*: The GTS cannot communicate with the ECM.




A

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

B

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
E8-12 (CHK) - A38-24 (W) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
E8-12 (CHK) - A52-24 (W) Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR