Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052774 1GR-FE ENGINE CONTROL _0255001 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0724  Brake Switch "B" Circuit High  


DESCRIPTION

The stop light switch is part of a duplex system that transmits 2 signals: STP and ST1-. These 2 signals are used by the ECM to monitor whether or not the brake system is working properly.

This DTC indicates that the stop light switch remains on. When the stop light switch remains on during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC.

DTC No. DTC Detection Condition Trouble Area
P0724 Stop light switch remains on even when the vehicle is driven in a GO (30 km/h (18.65 mph) or more) and STOP (less than 3 km/h (1.86 mph)) pattern 5 times (2 trip detection logic).
·

Short in stop light switch signal circuit

·

Stop light switch assembly

·

ECM



MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains on. When the stop light switch remains on during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC. The vehicle must GO (30 km/h (18.65 mph) or more) and STOP (less than 3 km/h (1.86 mph)) 5 times for 2 driving cycles in order for the DTC to be stored.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


1.

Warm up the engine.

2.

Turn the ignition switch off.

3.

Connect the GTS to the DLC3.

4.

Turn the ignition switch to ON.

5.

Turn the GTS on.

6.

Enter the following menus: Powertrain / Engine and ECT / Data List.

7.

According to the display on the GTS, read the Data List.


GTS Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light Switch Stop light switch status/ON or OFF
·

Brake pedal depressed: ON

·

Brake pedal released: OFF


-

PROCEDURE

1.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION).



OK

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)
U163722E01
1.773,0.365 1.967,0.527 0.194,0.162 10 *b 0.22,0.365 0.428,0.552 0.209,0.187 10 *a 0.271,2.273 0.429,2.474 0.158,0.200 10 *c 2.636,3.323 3.239,3.505 0.604,0.181 10 36 (STP) 1.867,3.649 2.572,3.427 false 1.123,2.679 1.414,2.860 0.291,0.181 10 A38 1.812,2.679 2.102,2.860 0.291,0.181 10 A52 1.504,2.679 1.684,2.825 0.180,0.145 10 *A 2.197,2.679 2.372,2.825 0.174,0.145 10 *B

a.

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
A38-36 (STP) - Body ground Brake pedal depressed 7.5 to 14 V
A38-36 (STP) - Body ground Brake pedal released Below 1.5 V

for RHD
Tester Connection Condition Specified Condition
A52-36 (STP) - Body ground Brake pedal depressed 7.5 to 14 V
A52-36 (STP) - Body ground Brake pedal released Below 1.5 V


Text in Illustration
*A for LHD
*B for RHD
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR