Refer to DTC P0136 (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0136).
When any of these DTCs is stored, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. The ECM continues operating in fail-safe mode until the ignition switch is turned off.
The ECM provides a pulse-width modulated control circuit to adjust the current through the heater. The heated oxygen sensor heater circuit uses a relay on the +B side of the circuit.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0037
P0057 |
The heater current is below the specified value while the heater is operating (1 trip detection logic). | ·
Open in heated oxygen sensor heater circuit ·
Heated oxygen sensor heater (sensor 2) ·
Integration relay (EFI) ·
ECM |
| P0038
P0058 |
The heater current is higher than the specified value while the heater is operating (1 trip detection logic). | ·
Short in heated oxygen sensor heater circuit ·
Heated oxygen sensor heater (sensor 2) ·
Integration relay (EFI) ·
ECM |
| P102D
P105D |
The heater current is higher than the specified value while the heater is not operating (1 trip detection logic). | ECM |
The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.
The ECM monitors the current applied to the heated oxygen sensor heater to check the heater for malfunctions.
If the heater current is outside the normal range, the signal transmitted by the heated oxygen sensor becomes inaccurate. When the current in the heated oxygen sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.
Refer to DTC P0136 (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0136).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Sensor 2 refers to the sensor mounted behind the Three-way Catalytic Converter (TWC) and located far from the engine assembly.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
Inspect the heated oxygen sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>HEATED OXYGEN SENSOR>INSPECTION).
OK
NG
Disconnect the heated oxygen sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C20-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| C21-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| *A | for Bank 1 Sensor 2 |
| *B | for Bank 2 Sensor 2 |
| *a | Front view of wire harness connector
(to Heated Oxygen Sensor) |
OK
NG
Disconnect the heated oxygen sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C20-1 (HT1B) - C45-45 (HT1B) | Always | Below 1 Ω |
| C21-1 (HT2B) - C45-44 (HT2B) | Always | Below 1 Ω |
| C20-1 (HT1B) or C45-45 (HT1B) - Body ground | Always | 10 kΩ or higher |
| C21-1 (HT2B) or C45-44 (HT2B) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C20-1 (HT1B) - C46-45 (HT1B) | Always | Below 1 Ω |
| C21-1 (HT2B) - C46-44 (HT2B) | Always | Below 1 Ω |
| C20-1 (HT1B) or C46-45 (HT1B) - Body ground | Always | 10 kΩ or higher |
| C21-1 (HT2B) or C46-44 (HT2B) - Body ground | Always | 10 kΩ or higher |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Start the engine.
Allow the engine to idle for 1 minute or more.
Read the output pending DTCs using the GTS.
| Result | Proceed to |
|---|---|
| No pending DTC is output | A |
| Pending DTC P0037, P0038, P0057, P0058, P102D and/or P105D is output | B |
A
B
Inspect the integration relay (EFI) (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).
OK
NG
Disconnect the heated oxygen sensor connector.
Remove the integration relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C20-2 (+B) - 1S-1 | Always | Below 1 Ω |
| C21-2 (+B) - 1S-1 | Always | Below 1 Ω |
| C20-2 (+B) or 1S-1 - Body ground | Always | 10 kΩ or higher |
| C21-2 (+B) or 1S-1 - Body ground | Always | 10 kΩ or higher |
OK
NG