Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2015.08–2016.08
RM2660E _51 Engine / Hybrid System _052774 1GR-FE ENGINE CONTROL _0255001 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, battery voltage is applied to the IGSW of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the coil, closing the contacts of the integration relay (EFI relay) and supplying power to either terminal +B or +B2 of the ECM.

WIRING DIAGRAM

A372105E02
0.545,5.211 1.028,5.397 0.482,0.185 10 Battery 3.283,6.006 5.240,6.345 1.956,0.339 10 *1: w/ Entry and Start System *2: w/o Entry and Start System 0.067,0.022 0.745,0.234 0.678,0.212 12 for LHD: 1.627,2.729 1.753,2.906 0.127,0.177 10 2 1.574,2.539 1.787,2.701 0.212,0.162 10 1R 3.308,4.834 4.434,5.025 1.127,0.191 10 Integration Relay 1.619,2.017 1.746,2.193 0.127,0.177 10 1 2.52,2.352 2.647,2.528 0.127,0.177 10 1 2.78,2.352 2.907,2.528 0.127,0.177 10 2 2.478,3.336 2.605,3.513 0.127,0.177 10 1 2.738,3.336 2.865,3.513 0.127,0.177 10 2 1.576,2.203 1.789,2.365 0.212,0.162 10 1Y 4.62,4.26 4.747,4.437 0.127,0.177 10 8 4.581,4.444 4.794,4.607 0.212,0.162 10 1S 4.627,3.696 4.754,3.872 0.127,0.177 10 4 4.587,3.89 4.799,4.052 0.212,0.162 10 1S 4.6,3.264 4.802,3.441 0.202,0.177 10 11 4.591,3.448 4.803,3.610 0.212,0.162 10 1S 4.642,2.015 4.769,2.192 0.127,0.177 10 7 4.593,2.195 4.806,2.357 0.212,0.162 10 1P 5.864,2.03 6.044,2.207 0.180,0.177 10 28 5.814,2.202 6.094,2.364 0.280,0.162 10 A38 2.076,3.574 3.096,3.754 1.019,0.180 10 EFI MAIN NO.1 2.889,4.099 3.908,4.279 1.019,0.180 10 EFI MAIN NO.1 2.385,2.068 3.077,2.236 0.692,0.168 10 IG2 MAIN 3.043,2.81 3.756,2.999 0.712,0.189 10 IG2 MAIN 3.908,2.075 4.035,2.252 0.127,0.177 10 1 4.165,2.075 4.292,2.252 0.127,0.177 10 2 3.651,2.375 4.650,2.543 0.999,0.168 10 ENG-IG2 NO.1 6.158,2.098 6.573,2.261 0.415,0.163 10 IGSW 5.901,2.912 6.038,3.089 0.137,0.177 10 3 5.808,3.073 6.088,3.235 0.280,0.162 10 A38 6.152,3.072 6.371,3.235 0.219,0.163 10 +B 5.901,3.286 6.038,3.463 0.137,0.177 10 2 5.808,3.447 6.088,3.609 0.280,0.162 10 A38 6.152,3.446 6.469,3.609 0.316,0.163 10 +B2 5.854,4.262 6.053,4.438 0.200,0.177 10 34 5.808,4.444 6.088,4.606 0.280,0.162 10 A38 6.152,4.352 6.559,4.515 0.407,0.163 10 MREL 5.854,5.278 6.053,5.455 0.200,0.177 10 81 5.808,5.458 6.088,5.620 0.280,0.162 10 C45 6.152,5.457 6.559,5.620 0.407,0.163 10 E1 6.424,5.964 6.781,6.115 0.357,0.151 10 ECM 3.383,0.926 3.507,1.068 0.124,0.142 10 6 3.383,0.646 3.507,0.788 0.124,0.142 10 5 3.593,1.021 3.872,1.186 0.279,0.165 10 IG2 3.583,0.741 3.907,0.906 0.323,0.165 10 AM2 2.559,0.596 2.882,0.761 0.323,0.165 10 AM2 0.415,0.876 1.031,1.041 0.616,0.165 10 J/B LH-B 0.534,2.347 0.921,2.513 0.387,0.165 10 P/I-B 3.649,1.508 4.722,1.690 1.073,0.181 10 Ignition Switch*2 3.649,1.362 3.958,1.536 0.308,0.174 10 E93 1.581,5.343 1.943,5.536 0.362,0.193 10 IG1D 1.363,5.254 1.570,5.430 0.208,0.177 10 3 1.581,5.763 1.963,5.926 0.382,0.163 10 E128 1.581,5.91 3.160,6.256 1.578,0.345 10 Certification ECU (Smart Key ECU Assembly)*1

A372110E02
0.545,5.233 1.028,5.418 0.482,0.185 10 Battery 0.067,0.044 0.745,0.256 0.678,0.212 12 for RHD: 1.627,2.75 1.753,2.927 0.127,0.177 10 2 1.574,2.56 1.787,2.722 0.212,0.162 10 1R 3.308,4.855 4.434,5.046 1.127,0.191 10 Integration Relay 1.619,2.038 1.746,2.214 0.127,0.177 10 1 2.52,2.373 2.647,2.550 0.127,0.177 10 1 2.78,2.373 2.907,2.550 0.127,0.177 10 2 2.478,3.357 2.605,3.534 0.127,0.177 10 1 2.738,3.357 2.865,3.534 0.127,0.177 10 2 1.576,2.224 1.789,2.386 0.212,0.162 10 1X 4.62,4.282 4.747,4.458 0.127,0.177 10 8 4.581,4.466 4.794,4.628 0.212,0.162 10 1S 4.627,3.717 4.754,3.894 0.127,0.177 10 4 4.587,3.911 4.799,4.073 0.212,0.162 10 1S 4.6,3.285 4.802,3.462 0.202,0.177 10 11 4.591,3.469 4.803,3.632 0.212,0.162 10 1S 4.642,2.036 4.769,2.213 0.127,0.177 10 7 4.593,2.216 4.806,2.378 0.212,0.162 10 1P 5.864,2.051 6.044,2.228 0.180,0.177 10 28 5.814,2.223 6.094,2.386 0.280,0.162 10 A52 2.076,3.595 3.096,3.775 1.019,0.180 10 EFI MAIN NO.1 2.889,4.12 3.908,4.300 1.019,0.180 10 EFI MAIN NO.1 2.379,2.089 3.070,2.257 0.691,0.168 10 IG2 MAIN 3.042,2.832 3.713,3.000 0.670,0.168 10 IG2 MAIN 3.908,2.097 4.035,2.273 0.127,0.177 10 1 4.165,2.097 4.292,2.273 0.127,0.177 10 2 3.651,2.396 4.650,2.564 0.999,0.168 10 ENG-IG2 NO.1 6.158,2.119 6.573,2.282 0.415,0.163 10 IGSW 5.901,2.933 6.038,3.110 0.137,0.177 10 3 5.808,3.094 6.088,3.256 0.280,0.162 10 A52 6.152,3.093 6.371,3.256 0.219,0.163 10 +B 5.901,3.307 6.038,3.484 0.137,0.177 10 2 5.808,3.468 6.088,3.630 0.280,0.162 10 A52 6.152,3.467 6.469,3.630 0.316,0.163 10 +B2 5.854,4.283 6.053,4.460 0.200,0.177 10 34 5.808,4.465 6.088,4.627 0.280,0.162 10 A52 6.152,4.373 6.559,4.536 0.407,0.163 10 MREL 5.854,5.299 6.053,5.476 0.200,0.177 10 81 5.808,5.479 6.088,5.641 0.280,0.162 10 C46 6.152,5.478 6.559,5.641 0.407,0.163 10 E1 6.424,5.985 6.781,6.136 0.357,0.151 10 ECM 3.383,0.948 3.507,1.090 0.124,0.142 10 6 3.383,0.668 3.507,0.810 0.124,0.142 10 5 3.593,1.042 3.872,1.207 0.279,0.165 10 IG2 3.583,0.762 3.907,0.927 0.323,0.165 10 AM2 2.559,0.617 2.882,0.783 0.323,0.165 10 AM2 0.415,0.898 1.031,1.063 0.616,0.165 10 J/B LH-B 0.534,2.369 0.921,2.534 0.387,0.165 10 P/I-B 3.649,1.53 4.722,1.711 1.073,0.181 10 Ignition Switch 3.649,1.383 3.958,1.557 0.308,0.174 10 E93

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - BATTERY)
U163775E04
0.115,0.083 0.385,0.302 0.271,0.219 10 false *a 0.5,1.688 0.771,1.906 0.271,0.219 10 false 1Y 0.49,2.094 0.76,2.313 0.271,0.219 10 false 1X 0.938,1.688 1.208,1.917 0.271,0.229 12 false *A 0.948,2.104 1.219,2.333 0.271,0.229 12 false *B

a.

Remove the integration relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD:
Tester Connection Condition Specified Condition
1Y-1 - Body ground Always 11 to 14 V

for RHD:
Tester Connection Condition Specified Condition
1X-1 - Body ground Always 11 to 14 V


Text in Illustration
*A for LHD:
*B for RHD:
*a Front view of wire harness connector (to Integration Relay)



OK

2.INSPECT INTEGRATION RELAY (EFI MAIN NO.1 RELAY AND IG2 MAIN NO.1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT INTEGRATION RELAY (EFI MAIN NO.1 RELAY AND IG2 MAIN NO.1 RELAY)

OK

3.CHECK HARNESS AND CONNECTOR (+B, +B2 AND MREL CIRCUIT)

NG

REPLACE INTEGRATION RELAY

3.CHECK HARNESS AND CONNECTOR (+B, +B2 AND MREL CIRCUIT)
a.

Check the harness and the connectors between the integration relay and the ECM.

i.

Remove the integration relay from the engine room relay block.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A38-34 (MREL) - 1S-8 Always Below 1 Ω
A38-3 (+B) - 1S-11 Always Below 1 Ω
A38-2 (+B2) - 1S-11 Always Below 1 Ω
A38-34 (MREL) or 1S-8 - Body ground Always 10 kΩ or higher
A38-3 (+B) or 1S-11 - Body ground Always 10 kΩ or higher
A38-2 (+B2) or 1S-11 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A52-34 (MREL) - 1S-8 Always Below 1 Ω
A52-3 (+B) - 1S-11 Always Below 1 Ω
A52-2 (+B2) - 1S-11 Always Below 1 Ω
A52-34 (MREL) or 1S-8 - Body ground Always 10 kΩ or higher
A52-3 (+B) or 1S-11 - Body ground Always 10 kΩ or higher
A52-2 (+B2) or 1S-11 - Body ground Always 10 kΩ or higher




b.

Check the harness and connectors between the integration relay and body ground.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1S-4 - Body ground Always Below 1 Ω





OK

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C45-81 (E1) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
C46-81 (E1) - Body ground Always Below 1 Ω




OK

5.INSPECT ECM (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT ECM (IGSW VOLTAGE)
A385610E02
2,1.927 2.563,2.521 true 2.438,3.5 2.688,4.25 true 0.219,0.208 2.615,0.76 2.396,0.552 10 false *a 1.094,0.927 1.469,1.177 0.375,0.25 10 false C45 1.479,0.875 1.667,1.063 0.188,0.188 10 false *A 1.979,0.927 2.354,1.177 0.375,0.25 10 false C46 2.396,0.865 2.583,1.052 0.188,0.188 10 false *B 2.625,2.448 3.24,2.698 0.615,0.25 10 false 81 (E1) 1.094,2.719 1.469,2.969 0.375,0.25 10 false A38 1.479,2.667 1.667,2.854 0.188,0.188 10 false *A 1.99,2.719 2.365,2.969 0.375,0.25 10 false A52 2.365,2.656 2.552,2.844 0.188,0.188 10 false *B 2.375,4.26 3.24,4.51 0.865,0.25 10 false 28 (IGSW)

a.

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
A38-28 (IGSW) - C45-81 (E1) Ignition switch ON 11 to 14 V

for RHD
Tester Connection Switch Condition Specified Condition
A52-28 (IGSW) - C46-81 (E1) Ignition switch ON 11 to 14 V


Text in Illustration
*A for LHD
*B for RHD
*a Front view of wire harness connector (to ECM)



OK

NG

6.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM, INTEGRATION RELAY - BODY GROUND)
6.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM, INTEGRATION RELAY - BODY GROUND)
a.

Remove the integration relay from the engine room relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
1P-7 - A38-28 (IGSW) Always Below 1 Ω
1P-7 or A38-28 (IGSW) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
1P-7 - A52-28 (IGSW) Always Below 1 Ω
1P-7 or A52-28 (IGSW) - Body ground Always 10 kΩ or higher




OK

7.CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM
Result
Result Proceed to
w/ Entry and Start System A
w/o Entry and Start System B


A

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE ROOM RELAY BLOCK

B

10.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ENGINE ROOM RELAY BLOCK)
8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE ROOM RELAY BLOCK
a.

Remove the integration relay from the engine room relay block.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E128-3 (IG1D) - 1R-2 Always Below 1 Ω
1S-4 - Body ground Always Below 1 Ω
E2-11 (IG2D) or 1R-2 - Body ground Always 10 kΩ or higher




OK

9.CHECK ENTRY AND START SYSTEM (POWER SOURCE MODE DOES NOT CHANGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ENGINE ROOM RELAY BLOCK)
a.

Remove the integration relay from the engine room relay block.


b.

Disconnect the ignition switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E93-6 (IG2) - 1R-2 Always Below 1 Ω
1S-4 - Body ground Always Below 1 Ω
E93-6 (IG2) or 1R-2 - Body ground Always 10 kΩ or higher




OK

11.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly (See page Engine / Hybrid System>1GR-FE (STARTING)>IGNITION SWITCH>INSPECTION).



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - BATTERY)

NG

REPLACE IGNITION SWITCH ASSEMBLY