| Vehicle Speed
|
Vehicle speed/
Min.: 0 km/h, Max.: 255 km/h
|
Actual vehicle speed
|
Speed indicated on the speedometer.
|
| Engine Speed
|
Engine speed/
Min.: 0 rpm, Max.: 16383 rpm
|
650 to 750 rpm: Idling
|
-
|
| Calculate Load
|
Load calculated by ECM/
Min.: 0%, Max.: 100%
|
·
10 to 18.9%: Driving without load (2500 rpm)
|
-
|
| Vehicle Load
|
Vehicle load/
Min.: 0%, Max.: 25700%
|
Actual vehicle load
|
-
|
| MAF
|
Airflow rate from mass air flow meter/
Min.: 0 gm/sec, Max.: 655.35 gm/sec
|
2.5 to 4.7 gm/sec: Idling
18.3 to 25.8 gm/sec: 3000 rpm (without load)
|
If the value is approximately 0.0 gm/sec:
·
The mass air flow meter power source circuit is open or shorted.
·
The VG circuit is open or shorted.
If the value is 160.0 gm/sec or more:
|
| Atmosphere Pressure
|
Atmospheric pressure/
Min.: 0 kPa, Max.: 255 kPa
|
Equivalent to atmospheric pressure (absolute pressure)
|
-
|
| Coolant Temp
|
Engine coolant temperature/
Min.: -40°C, Max.: 140°C
|
80 to 100°C (176 to 212°F): After warming up
|
If the value is -40°C (-40°F), the sensor circuit is open.
If the value is 140°C (284°F), the sensor circuit is shorted.
|
| Intake Air
|
Intake air temperature/
Min.: -40°C, Max.: 140°C
|
Equivalent to ambient air temperature
|
If the value is -40°C (-40°F), the sensor circuit is open.
If the value is 140°C (284°F), the sensor circuit is shorted.
|
| Engine Run Time
|
Engine run time/
Min.: 0 s, Max.: 65535 s
|
Time after engine start
|
Service data.
|
| Initial Engine Coolant Temp
|
Initial engine coolant temperature/
Min.: -40°C, Max.: 119.3°C
|
Close to ambient air temperature
|
Service data.
|
| Initial Intake Air Temp
|
Initial intake air temperature/
Min.: -40°C, Max.: 119.3°C
|
Close to ambient air temperature
|
Service data.
|
| Battery Voltage
|
Battery voltage/
Min.: 0 V, Max.: 65.535 V
|
11 to 14 V: Idling
|
-
|
| Glow Indicator Supported
|
Status of glow indicator supported/
Unsupp or Supp
|
-
|
-
|
| Glow Indicator
|
Glow indicator/
ON or OFF
|
-
|
-
|
| Accelerator Position
|
Accelerator pedal position/
Min.: 0%, Max.: 399.9%
|
Actual accelerator pedal position
|
-
|
| Accel Sens. No.1 Volt %
|
Absolute Accelerator Pedal Position (APP) No. 1/
Min.: 0%, Max.: 100%
|
·
10 to 22%: Accelerator pedal released
·
52 to 90%: Accelerator pedal fully depressed
|
-
|
| Accel Sens. No.2 Volt %
|
Absolute APP No. 2/
Min.: 0%, Max.: 100%
|
·
24 to 40%: Accelerator pedal released
·
68 to 95%: Accelerator pedal fully depressed
|
-
|
| Accel Sensor Out No.1
|
APP sensor No. 1 voltage/
Min.: 0 V, Max.: 4.98 V
|
·
0.5 to 1.1 V: Accelerator pedal released
·
2.6 to 4.5 V: Accelerator pedal fully depressed
|
-
|
| Accel Sensor Out No.2
|
APP sensor No. 2 voltage/
Min.: 0 V, Max.: 4.98 V
|
·
1.2 to 2.0 V: Accelerator pedal released
·
3.4 to 4.75 V: Accelerator pedal fully depressed
|
-
|
| Accelerator Idle Position
|
Whether or not accelerator pedal position sensor detecting idle/
ON or OFF
|
ON: Idling
|
-
|
| Accel Fully Close Learn #1
|
Accelerator pedal fully released learned value No. 1/
Min.: 0 deg, Max.: 124.5 deg
|
-
|
ETCS service data.
|
| Accel Fully Close Learn #2
|
Accelerator pedal fully released learned value No. 2/
Min.: 0 deg, Max.: 124.5 deg
|
-
|
ETCS service data.
|
| Throttle Sensor Volt %
|
Absolute throttle position sensor/
Min.: 0%, Max.: 100%
|
·
10 to 22%: Throttle fully closed
·
64 to 96%: Throttle fully open
|
The calculated value based on VTA1.
|
| Throttl Sensor #2 Volt %
|
Throttle position sensor #2/
Min.: 0%, Max.: 100%
|
·
42 to 62%: Throttle fully closed
·
92 to 100%: Throttle fully open
|
The calculated value based on VTA2.
|
| ST1
|
Brake pedal signal/
ON or OFF
|
ON: Brake pedal depressed
|
-
|
| System Guard
|
System guard/
ON or OFF
|
-
|
ETCS service data.
|
| Open Side Malfunction
|
Open side malfunction/
ON or OFF
|
-
|
ETCS service data.
|
| Throttle Idle Position
|
Whether or not throttle position sensor detecting idle/
ON or OFF
|
·
ON: Accelerator pedal released
·
OFF: Accelerator pedal depressed
|
-
|
| Throttle Require Position
|
Required throttle position/
Min.: 0 V, Max.: 4.98 V
|
0.5 to 1.1 V: Idling
|
-
|
| Throttle Sensor Position*
|
Throttle sensor position/
Min.: 0%, Max.: 100%
|
·
0%: Throttle fully closed
·
50 to 80%: Throttle fully open
|
Recognition value of the throttle opening angle in the ECM.
|
| Throttle Position No. 1
|
Throttle position sensor No. 1 output voltage/
Min.: 0 V, Max.: 4.98 V
|
·
0.5 to 1.1 V: Accelerator pedal released
·
3.2 to 4.8 V: Accelerator pedal fully depressed
·
0.6 to 1.4 V: Fail-safe operating
|
-
|
| Throttle Position No. 2
|
Throttle position sensor No. 2 output voltage/
Min.: 0 V, Max.: 4.98 V
|
·
2.1 to 3.1 V: Accelerator pedal released
·
4.6 to 5.0 V: Accelerator pedal fully depressed
·
2.1 to 3.1 V: Fail-safe operating
|
-
|
| Throttle Position Command
|
Throttle position command value/
Min.: 0 V, Max.: 4.98 V
|
0.5 to 4.8 V
|
-
|
| Throttle Sens Open Pos #1
|
Throttle position sensor No. 1/
Min.: 0 V, Max.: 4.98 V
|
0.6 to 1.4 V
|
ETCS service data.
|
| Throttle Sens Open Pos #2
|
Throttle position sensor No. 2/
Min.: 0 V, Max.: 4.98 V
|
1.7 to 2.5 V
|
ETCS service data.
|
| Throttle Motor Current
|
Throttle actuator current/
Min.: 0 A, Max.: 19.9 A
|
0 to 3.0 A: Idling
|
ETCS service data.
|
| Throttle Motor DUTY
|
Throttle actuator/
Min.: 0%, Max.: 100%
|
0.5 to 40%: Idling
|
ETCS service data.
|
| Throttle Motor Duty (Open)
|
Throttle actuator duty ratio (open)/
Min.: 0%, Max.: 255%
|
0 to 40%: Idling
|
ETCS service data.
|
| Throttle Motor Duty (Close)
|
Throttle actuator duty ratio (close)/
Min.: 0%, Max.: 255%
|
0 to 40%: Idling
|
ETCS service data.
|
| Throttle Fully Close Learn
|
Throttle valve fully closed (learned value)/
Min.: 0 V, Max.: 4.98 V
|
0.4 to 1.0 V: Accelerator pedal released
|
-
|
| +BM Voltage
|
+BM voltage/
Min.: 0 V, Max.: 79.998 V
|
11 to 14 V: Ignition switch ON and system normal
|
ETCS service data.
|
| Actuator Power Supply
|
Actuator power supply/
ON or OFF
|
ON: Idling
|
ETCS service data.
|
| Throttle Position
|
Throttle valve opening angle/
Min.: 0 deg, Max.: 499.99 deg
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| ISC Flow
|
Flow rate calculated using information from each sensor/
Min.: 0 L/s, Max.: 79.99 L/s
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| ISC Position
|
Requested opening amount calculated using ISC control/
Min.: 0 deg, Max.: 499.99 deg
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| ISC Feedback Value
|
ISC feedback compensation amount/
Min.: -40 L/s, Max.: 39.99 L/s
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| ISC Learning Value
|
ISC learned compensation amount/
Min.: -40 L/s, Max.: 39.99 L/s
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Electric Load Feedback Val
|
Compensation flow rate according to electrical load/
Min.: -40 L/s, Max.: 39.99 L/s
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Air Conditioner FB Val
|
Compensation flow rate according to air conditioner load/
Min.: -40 L/s, Max.: 39.99 L/s
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| PS Feedback Val
|
Compensation flow rate according to power steering load/
Min.: -40 L/s, Max.: 39.99 L/s
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Low Revolution Control
|
Low engine speed control operation state/
ON or OFF
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| N Range Status
|
Shift lever N status/
ON or OFF
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Eng Stall Control FB Flow
|
Intake air compensation flow rate/
Min.: -40 L/s, Max.: 39.99 L/s
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Deposit Loss Flow
|
Flow loss due to deposits/
Min.: -40 L/s, Max.: 39.99 L/s
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Fuel Pump Duty
|
Fuel pump duty/
Min.: 0%, Max.: 399.9%
|
-
|
-
|
| Injector (Port)
|
Injection period of No. 1 cylinder/
Min.: 0 μs, Max.: 65535 μs
|
1600 to 2400 μs: Idling
|
-
|
| Injection Volum (Cylinder 1)
|
Injection volume (cylinder 1)/
Min.: 0 ml, Max.: 2.047 ml
|
0 to 0.5 ml
|
Fuel injection volume of 10 injections.
|
| Current Fuel Type
|
Status of the current fuel type
|
Gasoline/petrol
|
-
|
| EVAP (Purge) VSV
|
Purge VSV control duty/
Min.: 0%, Max.: 100%
|
0 to 100%: During idling
|
Command signal from the ECM.
|
| Evap Purge Flow
|
Purge flow/
Min.: 0%, Max.: 399.9%
|
0 to 100%: Idling
|
-
|
| Purge Density Learn Value
|
Purge density learned value/
Min.: -200, Max.: 199.993
|
Idling: -40 to 0
|
Service data.
|
| EVAP Purge VSV
|
VSV status for EVAP control/
ON or OFF
|
-
|
-
|
| Purge Cut VSV Duty
|
Purge cut VSV duty/
Min.: 0%, Max.: 399.9%
|
-
|
-
|
| Target Air-Fuel Ratio
|
Target air fuel ratio/
Min.: 0, Max.: 1.99
|
0.8 to 1.2: During idling
|
-
|
| AF Lambda B1S1
|
Output air fuel ratio associated with bank 1 sensor 1/
Min.: 0, Max.: 1.99
|
·
Value less than 1 (0.000 to 0.999) = Rich
·
1 = Stoichiometric air fuel ratio
·
Value more than 1 (1.001 to 1.999) = Lean
|
-
|
| AF Lambda B2S1
|
Output air fuel ratio associated with bank 2 sensor 1/
Min.: 0, Max.: 1.99
|
·
Value less than 1 (0.000 to 0.999) = Rich
·
1 = Stoichiometric air fuel ratio
·
Value more than 1 (1.001 to 1.999) = Lean
|
-
|
| AFS Voltage B1S1
|
Air fuel ratio sensor output voltage (for Bank 1 Sensor 1)/
Min.: 0 V, Max.: 7.99 V
|
2.8 to 3.8 V: Idling
|
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
|
| AFS Voltage B2S1
|
Air fuel ratio sensor output voltage (for Bank 2 Sensor 1)/
Min.: 0 V, Max.: 7.99 V
|
2.8 to 3.8 V: Idling
|
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
|
| AFS Current B1S1
|
Air fuel ratio sensor current (for Bank 1 Sensor 1)/
Min.: -128 mA, Max.: 127.99 mA
|
-0.5 to 0.5 mA: Idling
|
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output current of the sensor.
|
| AFS Current B2S1
|
Air fuel ratio sensor current (for Bank 2 Sensor 1)/
Min.: -128 mA, Max.: 127.99 mA
|
-0.5 to 0.5 mA: Idling
|
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output current of the sensor.
|
| A/F Heater Duty B1S1
|
Air fuel ratio sensor heater duty ratio (for Bank 1)/
Min.: 0%, Max.: 399.9%
|
0 to 100%
|
-
|
| A/F Heater Duty B2S1
|
Air fuel ratio sensor heater duty ratio (for Bank 2)/
Min.: 0%, Max.: 399.9%
|
0 to 100%
|
-
|
| O2S B1S2
|
Heated oxygen sensor output voltage (for Bank 1 Sensor 2)/
Min.: 0 V, Max.: 1.275 V
|
0.1 to 0.9 V:
Driving at 70 km/h (44 mph)
|
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
|
| O2S B2S2
|
Heated oxygen sensor output voltage (for Bank 2 Sensor 2)/
Min.: 0 V, Max.: 1.275 V
|
0.1 to 0.9 V:
Driving at 70 km/h (44 mph)
|
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
|
| O2 Heater B1S2
|
Heated oxygen sensor heater (for Bank 1 Sensor 2)/
Active or Not Act
|
-
|
-
|
| O2 Heater B2S2
|
Heated oxygen sensor heater (for Bank 2 Sensor 2)/
Active or Not Act
|
-
|
-
|
| O2 Heater Curr Val B1S2
|
Heated oxygen sensor current (for Bank 1 Sensor 2)/
Min.: 0 A, Max.: 4.9 A
|
-
|
-
|
| O2 Heater Curr Val B2S2
|
Heated oxygen sensor current (for Bank 2 Sensor 2)/
Min.: 0 A, Max.: 4.9 A
|
-
|
-
|
| Short FT #1
|
Short-term fuel trim of bank 1/
Min.: -100%, Max.: 99.2%
|
-20 to +20%
|
This item refers to the short-term fuel compensation used to maintain the air fuel ratio at the stoichiometric air-fuel ratio.
|
| Long FT #1
|
Long-term fuel trim of bank 1/
Min.: -100%, Max.: 99.2%
|
-20 to +20%
|
·
This item refers to the overall fuel compensation carried out in the long term to compensate for a continual deviation of the short-term fuel trim from the central value.
·
Air fuel ratio feedback leaning is divided up according to the engine operating range (engine speed x load), and separate values are stored for each operating range. "Long FT #1" indicates the learned value for the current operating range. [A/F Learn Value Idle #1], [A/F Learn Value Low #1], [A/F Learn Value Mid1 #1], [A/F Learn Value Mid2 #1] and [A/F Learn Value High #1] indicate the leaned values for the different operating ranges. The learned value that is the same as "Long FT #1" indicates the current engine operating range.
|
| A/F Learn Value Idle #1
|
Air-fuel ratio learned value for idling (bank 1)/
Min.: -50%, Max.: 49.6%
|
-20 to +20%
|
Learning is performed when idling with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher).
|
| A/F Learn Value Low #1
|
Air-fuel ratio learned value for low engine loads (bank 1)/
Min.: -50%, Max.: 49.6%
|
-20 to +20%
|
Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts).
|
| A/F Learn Value Mid1 #1
|
Air-fuel ratio learned value for mid-sized engine loads 1 (bank 1)/
Min.: -50%, Max.: 49.6%
|
-20 to +20%
|
Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into four parts).
|
| A/F Learn Value Mid2 #1
|
Air-fuel ratio learned value for mid-sized engine loads 2 (bank 1)/
Min.: -50%, Max.: 49.6%
|
-20 to +20%
|
Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the mid-size load range closer to the high load range (when the range of engine loads is divided into four parts).
|
| A/F Learn Value High #1
|
Air-fuel ratio learned value for high engine loads (bank 1)/
Min.: -50%, Max.: 49.6%
|
-20 to +20%
|
Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts).
|
| Total FT #1
|
Total fuel trim of bank 1/
Min.: -0.5, Max.: 0.496
|
-0.2 to 0.2: Idling
|
-
|
| Short FT #2
|
Short-term fuel trim of bank 2/
Min.: -100%, Max.: 99.2%
|
-20 to +20%
|
This item refers to the short-term fuel compensation used to maintain the air fuel ratio at the stoichiometric air-fuel ratio.
|
| Long FT #2
|
Long-term fuel trim of bank 2/
Min.: -100%, Max.: 99.2%
|
-20 to +20%
|
·
This item refers to the overall fuel compensation carried out in the long term to compensate for a continual deviation of the short-term fuel trim from the central value.
·
Air fuel ratio feedback leaning is divided up according to the engine operating range (engine speed x load), and separate values are stored for each operating range. "Long FT #2" indicates the learned value for the current operating range. [A/F Learn Value Idle #2], [A/F Learn Value Low #2], [A/F Learn Value Mid1 #2], [A/F Learn Value Mid2 #2] and [A/F Learn Value High #2] indicate the leaned values for the different operating ranges. The learned value that is the same as "Long FT #2" indicates the current engine operating range.
|
| A/F Learn Value Idle #2
|
Air-fuel ratio learned value for idling (bank 2)/
Min.: -50%, Max.: 49.6%
|
-20 to +20%
|
Learning is performed when idling with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher).
|
| A/F Learn Value Low #2
|
Air-fuel ratio learned value for low engine loads (bank 2)/
Min.: -50%, Max.: 49.6%
|
-20 to +20%
|
Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts).
|
| A/F Learn Value Mid1 #2
|
Air-fuel ratio learned value for mid-sized engine loads 1 (bank 2)/
Min.: -50%, Max.: 49.6%
|
-20 to +20%
|
Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into four parts).
|
| A/F Learn Value Mid2 #2
|
Air-fuel ratio learned value for mid-sized engine loads 2 (bank 2)/
Min.: -50%, Max.: 49.6%
|
-20 to +20%
|
Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the mid-size load range closer to the high load range (when the range of engine loads is divided into four parts).
|
| A/F Learn Value High #2
|
Air-fuel ratio learned value for high engine loads (bank 2)/
Min.: -50%, Max.: 49.6%
|
-20 to +20%
|
Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts).
|
| Total FT #2
|
Total fuel trim of bank 2/
Min.: -0.5, Max.: 0.496
|
-0.2 to 0.2: Idling
|
-
|
| Fuel System Status #1
|
Fuel system status (Bank 1)/
OL, CL, OL Drive, OL Fault or CL Fault
|
CL: Idling after warming up
|
·
OL (Open Loop): Has not yet satisfied conditions to go to closed loop.
·
CL (Closed Loop): Feedback for fuel control.
·
OL Drive: Open loop due to driving conditions (fuel enrichment).
·
OL Fault: Open loop due to a detected system fault.
·
CL Fault: Closed loop but the air fuel ratio sensor, which is used for fuel control, is malfunctioning.
|
| Fuel System Status #2
|
Fuel system status (Bank 2)/
OL, CL, OL Drive, OL Fault or CL Fault
|
CL: Idling after warming up
|
·
OL (Open Loop): Has not yet satisfied conditions to go to closed loop.
·
CL (Closed Loop): Feedback for fuel control.
·
OL Drive: Open loop due to driving conditions (fuel enrichment).
·
OL Fault: Open loop due to a detected system fault.
·
CL Fault: Closed loop but the air fuel ratio sensor, which is used for fuel control, is malfunctioning.
|
| Air Pump Pressure (Absolute)
|
Air pump pressure (absolute) (for Bank 1)/
Min.: 0 kPa, Max.: 65535 kPa
|
Atmospheric pressure +1 kPa or more: Air pump on, emission control valve open
Close to atmospheric pressure: Air pump off, emission control closed
|
Refer to DTC P2431
(See page ( )).
|
| Air Pump2 Pressure (Absolute)
|
Air pump pressure (absolute) (for Bank 2)/
Min.: 0 kPa, Max.: 65535 kPa
|
Atmospheric pressure +1 kPa or more: Air pump on, emission control valve open
Close to atmospheric pressure: Air pump off, emission control valve closed
|
Refer to DTC P2431
(See page ( )).
|
| Air Pump Pulsation Pressure
|
Air pump pulsation pressure/
Min.: 0 kPa, Max.: 655.35 kPa
|
-
|
Cumulative pulsation pressure calculated by ECM
(See page ( )).
|
| Secondary Air Control VSV
|
Secondary air control VSV status/
ON or OFF
|
ON: Secondary air control VSV operating
|
-
|
| 2nd Air System Status
|
Secondary air system status/
ON or OFF
|
ON: Secondary air injection system operating
|
-
|
| AI Test
|
AI operation prohibition/
READY or NOT RDY
|
READY
|
-
|
| Subfreezing Conditions
|
Subfreezing conditions status/
ON or OFF
|
-
|
-
|
| Air Pump Heater
|
Air pump heater status/
ON or OFF
|
-
|
Active Test support data.
|
| IGN Advance
|
Ignition timing advance for No. 1 cylinder/
Min.: -64 deg, Max.: 63.5 deg
|
BTDC 7 to 24 deg: Idling
|
-
|
| Knock Feedback Value
|
Knocking feedback value/
Min.: -1024drg(CA), Max.: 1023.9deg(CA)
|
-3deg(CA):
Driving at 70 km/h (44 mph)
|
Service data.
|
| Knock Correct Learn Value
|
Knocking correction learned value/
Min.: -1024deg(CA), Max.: 1023.9deg(CA)
|
5 to 28deg(CA):
Driving at 70 km/h (44 mph)
|
Service data.
|
| Idle Spark Advn Ctrl #1
|
Individual cylinder timing advance compensation amount (No. 1)/
Min.: 0deg(CA), Max.: 15.93deg(CA)
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Idle Spark Advn Ctrl #2
|
Individual cylinder timing advance compensation amount (No. 2)/
Min.: 0°CA, Max.: 15.93°CA
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Idle Spark Advn Ctrl #3
|
Individual cylinder timing advance compensation amount (No. 3)/
Min.: 0°CA, Max.: 15.93°CA
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Idle Spark Advn Ctrl #4
|
Individual cylinder timing advance compensation amount (No. 4)/
Min.: 0°CA, Max.: 15.93°CA
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Idle Spark Advn Ctrl #5
|
Individual cylinder timing advance compensation amount (No. 5)/
Min.: 0°CA, Max.: 15.93°CA
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Idle Spark Advn Ctrl #6
|
Individual cylinder timing advance compensation amount (No. 6)/
Min.: 0°CA, Max.: 15.93°CA
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| VVT Control Status #1
|
Variable valve timing (VVT) control status (Bank 1)/
ON or OFF
|
-
|
-
|
| VVT Control Status #2
|
VVT control status (Bank 2)/
ON or OFF
|
-
|
-
|
| VVT Advance Fail
|
VVT control failure status/
ON or OFF
|
ON: VVT control failure
|
-
|
| VVT Aim Angle #1
|
VVT target duty (Bank 1)/
Min.: 0%, Max.: 399.9%
|
-
|
VVT duty signal value during forced operation.
|
| VVT Change Angle #1
|
VVT displacement angle (Bank 1)/
Min.: 0 DegFR, Max.: 639.9 DegFR
|
-
|
Displacement angle during forced operation.
|
| VVT OCV Duty #1
|
Camshaft timing oil control valve operation duty (for Intake Side of Bank 1)/
Min.: 0%, Max.: 399.9%
|
-
|
Requested duty value for forced operation.
|
| VVT Aim Angle #2
|
VVT target duty (Bank 2)/
Min.: 0%, Max.: 399.9%
|
-
|
VVT duty signal value during forced operation.
|
| VVT Change Angle #2
|
VVT displacement angle (for Intake Side of Bank 2)/
Min.: 0 DegFR, Max.: 639.9 DegFR
|
-
|
Displacement angle during forced operation.
|
| VVT OCV Duty #2
|
Camshaft timing oil control valve operation duty (Bank 2)/
Min.: 0%, Max.: 399.9%
|
-
|
Requested duty value for forced operation.
|
| VVT Ex Hold Lrn Val #1
|
VVT exhaust hold duty ratio learned value (Bank 1)/
Min.: 0%, Max.: 399.9%
|
-
|
Learned duty value for forced operation.
|
| VVT Ex Chg Angle #1
|
VVT exhaust displacement angle (Bank 1)/
Min.: 0 DegFR, Max.: 639.9 DegFR
|
-
|
Displacement angle during forced operation.
|
| VVT Ex OCV Duty #1
|
Camshaft timing oil control valve duty (for Exhaust Side of Bank 1)/
Min.: 0%, Max.: 399.9%
|
-
|
Requested duty value for forced operation.
|
| VVT Ex Hold Lrn Val #2
|
VVT exhaust hold duty ratio learned value (Bank 2)/
Min.: 0%, Max.: 399.9%
|
-
|
Learned duty value for forced operation.
|
| VVT Ex Chg Angle #2
|
VVT exhaust displacement angle (Bank 2)/
Min.: 0 DegFR, Max.: 639.9 DegFR
|
-
|
Displacement angle during forced operation.
|
| VVT Ex OCV Duty #2
|
Camshaft timing oil control valve duty (for Exhaust Side of Bank 2)/
Min.: 0%, Max.: 399.9%
|
-
|
Requested duty value for forced operation.
|
| VVT Target Angle #1
|
VVT intake target angle (Bank 1)
Min.: 0 DegFR, Max.: 639.9 DegFR
|
-
|
-
|
| VVT Target Angle #2
|
VVT intake target angle (Bank 2)
Min.: 0 DegFR, Max.: 639.9 DegFR
|
-
|
-
|
| VVT Ex Target Angle #1
|
VVT exhaust target angle (Bank 1)
Min.: 0 DegFR, Max.: 639.9 DegFR
|
-
|
-
|
| VVT Ex Target Angle #2
|
VVT exhaust target angle (Bank 2)
Min.: 0 DegFR, Max.: 639.9 DegFR
|
-
|
-
|
| VN Turbo Type
|
VN turbo type/
Not Avl, Commo, Vacuum or CAN Com
|
Not Avl
|
-
|
| Catalyst Temp B1S1
|
Catalyst temperature (Bank 1, Sensor 1)/
Min.: -40°C, Max.: 6513.5°C
|
-
|
-
|
| Catalyst Temp B2S1
|
Catalyst temperature (Bank 2, Sensor 1)/
Min.: -40°C, Max.: 6513.5°C
|
-
|
-
|
| Catalyst Temp B1S2
|
Catalyst temperature (Bank 1, Sensor 2)/
Min.: -40°C, Max.: 6513.5°C
|
-
|
-
|
| Catalyst Temp B2S2
|
Catalyst temperature (Bank 2, Sensor 2)/
Min.: -40°C, Max.: 6513.5°C
|
-
|
-
|
| Starter Signal
|
Starter signal/
ON or OFF
|
ON: Starter operating
OFF: Starter not operating
|
-
|
| Power Steering Signal
|
Power steering oil pressure sensor signal/
ON or OFF
|
ON: Power steering operating
|
-
|
| Neutral Position SW Signal
|
PNP switch status/
ON or OFF
|
ON: P or N position
|
-
|
| Clutch Switch
|
Clutch switch status/
ON or OFF
|
ON: Clutch pedal depressed
|
-
|
| Clutch Start SW
|
Clutch start switch status/
ON or OFF
|
ON: Clutch pedal depressed
|
-
|
| Transfer L4
|
L4 status of the transfer/
ON or OFF
|
ON: 4WD control switch in 4L position
|
-
|
| Stop Light Switch
|
Stop light switch/
ON or OFF
|
ON: Brake pedal depressed
|
-
|
| A/C Signal
|
A/C switch status/
ON or OFF
|
ON: A/C on
|
-
|
| Closed Throttle Position SW
|
Closed throttle position switch/
ON or OFF
|
·
ON: Throttle fully closed
|
-
|
| Fuel Cut Condition
|
Fuel cut condition/
ON or OFF
|
ON: Fuel cut operating
|
-
|
| Immobiliser Communication
|
Immobiliser communication/
ON or OFF
|
ON: Normal
|
-
|
| Check Mode
|
Check mode/
ON or OFF
|
ON: Check mode on
|
Refer to Check Mode Procedure (See page ( )).
|
| SPD Test Result
|
Check mode result for vehicle speed sensor/
Compl or Incmpl
|
-
|
-
|
| AS Test Result
|
Check mode result for secondary air injection system/
Compl or Incmpl
|
-
|
-
|
| Misfire Test Result
|
Check mode result for misfire monitor/
Compl or Incmpl
|
-
|
-
|
| OXS1 Test Result
|
Check mode result for heated oxygen sensor (Bank 1)/
Compl or Incmpl
|
-
|
-
|
| OXS2 Test Result
|
Check mode result for heated oxygen sensor (Bank 2)/
Compl or Incmpl
|
-
|
-
|
| A/F Test Results #2
|
Check mode result for air fuel ratio sensor (Bank 2)/
Compl or Incmpl
|
-
|
-
|
| A/F Test Results #1
|
Check mode result for air fuel ratio sensor (Bank 1)/
Compl or Incmpl
|
-
|
-
|
| Complete Parts Monitor
|
Comprehensive component monitor/
Not Avl or Avail
|
-
|
-
|
| Fuel System Monitor
|
Fuel system monitor/
Not Avl or Avail
|
-
|
-
|
| Misfire Monitor
|
Misfire monitor/
Not Avl or Avail
|
-
|
-
|
| EGR/VVT Monitor
|
EGR/VVT monitor/
Not Avl or Avail
|
-
|
-
|
| EGR/VVT Monitor
|
EGR/VVT monitor/
Compl or Incmpl
|
-
|
-
|
| O2S(A/FS) Heater Monitor
|
O2S (A/FS) heater monitor/
Not Avl or Avail
|
-
|
-
|
| O2S(A/FS) Heater Monitor
|
O2S (A/FS) heater monitor/
Compl or Incmpl
|
-
|
-
|
| O2S(A/FS) Monitor
|
O2S (A/FS) monitor/
Not Avl or Avail
|
-
|
-
|
| O2S(A/FS) Monitor
|
O2S (A/FS) monitor/
Compl or Incmpl
|
-
|
-
|
| A/C Monitor
|
A/C monitor/
Not Avl or Avail
|
-
|
-
|
| A/C Monitor
|
A/C monitor/
Compl or Incmpl
|
-
|
-
|
| 2nd Air Monitor
|
2nd air monitor/
Not Avl or Avail
|
-
|
-
|
| 2nd Air Monitor
|
2nd air monitor/
Compl or Incmpl
|
-
|
-
|
| EVAP Monitor
|
EVAP monitor/
Not Avl or Avail
|
-
|
-
|
| EVAP Monitor
|
EVAP monitor/
Compl or Incmpl
|
-
|
-
|
| Heated Catalyst Monitor
|
Heated catalyst monitor/
Not Avl or Avail
|
-
|
-
|
| Heated Catalyst Monitor
|
Heated catalyst monitor/
Compl or Incmpl
|
-
|
-
|
| Catalyst Monitor
|
Catalyst monitor/
Not Avl or Avail
|
-
|
-
|
| Catalyst Monitor
|
Catalyst monitor/
Compl or Incmpl
|
-
|
-
|
| TC Terminal
|
TC terminal status/
ON or OFF
|
-
|
-
|
| # Codes (Include History)
|
Number of codes/
Min.: 0, Max.: 255
|
-
|
Number of DTCs stored.
|
| MIL
|
MIL status/
ON or OFF
|
ON: MIL on
|
-
|
| MIL ON Run Distance
|
Distance driven with MIL on/
Min.: 0 km, Max.: 65535 km
|
Distance driven after DTC stored
|
-
|
| Running Time from MIL ON
|
Running time from MIL ON/
Min.: 0 min, Max.: 65535 min
|
Running time after MIL turned on
|
-
|
| Time after DTC Cleared
|
Time after DTCs cleared/
Min.: 0 min, Max.: 65535 min
|
Time after DTCs cleared
|
-
|
| Distance from DTC Cleared
|
Distance driven after DTCs cleared/
Min.: 0 km, Max.: 65535 km
|
Distance driven after DTCs cleared
|
-
|
| Warmup Cycle Cleared DTC
|
Warmup cycles after DTCs cleared/
Min.: 0, Max.: 255
|
-
|
Number of warmup cycles after the DTCs are cleared.
|
| Dist Batt Cable Disconnect
|
Distance driven after battery cable disconnected/
Min.: 0 km, Max.: 65535 km
|
Total distance vehicle driven after battery cable disconnected
|
-
|
| IG OFF Elapsed Time
|
Time after ignition switch turned off/
Min.: 0 min, Max.: 655350 min
|
Cumulative time after ignition switch turned off
|
-
|
| OBD Requirements
|
OBD requirement
|
EOBD (Euro OBD)
|
-
|
| Number of Emission DTC
|
Emissions-related DTCs
|
-
|
Number of emissions-related DTCs.
|
| TC and TE1
|
TC and CG (TE1) terminals of DLC3/
ON or OFF
|
-
|
-
|
| Total Distance Traveled
|
Total distance traveled/
Min.: 0 km (0 mile), Max.: 16777215 km (10425361 mile)
|
-
|
-
|
| Ignition Trig. Count
|
Ignition counter/
Min.: 0, Max.: 65535
|
0 to 600
|
-
|
Cylinder #1 Misfire Count
to
Cylinder #6 Misfire Count
|
Misfire count of cylinder 1 to 6/
Min.: 0, Max.: 255
|
0
|
-
|
| All Cylinders Misfire Count
|
Misfire count of all cylinders/
Min.: 0, Max.: 255
|
0 to 35
|
-
|
| Misfire RPM
|
Engine speed for first misfire range/
Min.: 0 rpm, Max.: 6375 rpm
|
0 rpm: Misfire 0
|
-
|
| Misfire Load
|
Engine load for first misfire range/
Min.: 0 g/rev, Max.: 3.98 g/rev
|
0 g/rev: Misfire 0
|
-
|
| Misfire Margin
|
Misfire monitoring/
Min.: -128%, Max.: 127%
|
0 to 99.2%
|
Misfire detection margin.
|
| Catalyst OT MF F/C
|
Fuel cut to prevent catalyst from overheating during misfire/
Not Avl or Avail
|
Avail: Fuel cut to prevent catalyst from overheating during misfire available
Not Avl: Fuel cut to prevent catalyst from overheating during misfire not available
|
-
|
| Cat OT MF F/C History
|
History of fuel cut to prevent catalyst from overheating during misfire/
ON or OFF
|
ON: Fuel cut operation history exists
|
-
|
| Cat OT MF F/C Cylinder #1
|
Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
|
ON: Fuel cut operating
|
-
|
| Cat OT MF F/C Cylinder #2
|
Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
|
ON: Fuel cut operating
|
-
|
| Cat OT MF F/C Cylinder #3
|
Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
|
ON: Fuel cut operating
|
-
|
| Cat OT MF F/C Cylinder #4
|
Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
|
ON: Fuel cut operating
|
-
|
| Cat OT MF F/C Cylinder #5
|
Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
|
ON: Fuel cut operating
|
-
|
| Cat OT MF F/C Cylinder #6
|
Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
|
ON: Fuel cut operating
|
-
|
| Engine Speed (Starter Off)
|
Engine speed when starter off/
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Starter Count
|
Number of times starter turned on after ignition switch turned to ON/
Min.: 0, Max.: 255
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Run Dist of Previous Trip
|
Distance driven during previous trip/
Min.: 0 km, Max.: 655.35 km
|
-
|
Before 5 seconds elapse after starting the engine, which is the DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip.
After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.
- HINT:
-
Run Dist of Previous Trip in the freeze frame data present when the startability malfunction occurred (DTC P1604 detected) indicates the distance driven during the previous trip, but in all other cases, such as for the snapshot data of the Data List (real-time measurements), or for freeze frame data present when DTCs other than P1604 were detected, the value indicates the distance driven during the current trip.
|
| Rough Idle Status
|
Status of the rough idle status/
Normal, Misfire, Continuous poor combustion, Intermittent poor combustion, Low frequency poor combustion
|
Normal
|
The following list of statuses indicates the degree and frequency of rough idling from highest to lowest.
Use this as a reference when trying to reproduce the rough idling.
2.
Continuous poor combustion
3.
Intermittent poor combustion
4.
Low frequency poor combustion
|
| Plural Cylinders Rough Idle
|
Status of the plural cylinders rough idle/
ON or OFF
|
OFF
|
Indicates multiple cylinders are the cause of rough idling when ON.
|
| Rough Idle #1
|
Status of the rough idle #1/
ON or OFF
|
OFF
|
·
Indicates speed has dropped compared to other cylinders and idling is rough for the indicated cylinder when ON.
·
This item indicates cylinders which are likely to be the cause of rough idle.
|
| Rough Idle #2
|
Status of the rough idle #2/
ON or OFF
|
OFF
|
·
Indicates speed has dropped compared to other cylinders and idling is rough for the indicated cylinder when ON.
·
This item indicates cylinders which are likely to be the cause of rough idle.
|
| Rough Idle #3
|
Status of the rough idle #3/
ON or OFF
|
OFF
|
·
Indicates speed has dropped compared to other cylinders and idling is rough for the indicated cylinder when ON.
·
This item indicates cylinders which are likely to be the cause of rough idle.
|
| Rough Idle #4
|
Status of the rough idle #4/
ON or OFF
|
OFF
|
·
Indicates speed has dropped compared to other cylinders and idling is rough for the indicated cylinder when ON.
·
This item indicates cylinders which are likely to be the cause of rough idle.
|
| Rough Idle #5
|
Status of the rough idle #5/
ON or OFF
|
OFF
|
·
Indicates speed has dropped compared to other cylinders and idling is rough for the indicated cylinder when ON.
·
This item indicates cylinders which are likely to be the cause of rough idle.
|
| Rough Idle #6
|
Status of the rough idle #6/
ON or OFF
|
OFF
|
·
Indicates speed has dropped compared to other cylinders and idling is rough for the indicated cylinder when ON.
·
This item indicates cylinders which are likely to be the cause of rough idle.
|
| Engine Starting Time
|
Time elapsed after engine started (interval between ignition switch to ON and off)/
Min.: 0 ms, Max.: 655350 ms
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Previous Trip Coolant Temp
|
Engine coolant temperature during previous trip/
Min.: -40°C, Max.: 215°C
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Previous Trip Intake Temp
|
Intake air temperature during previous trip/
Min.: -40°C, Max.: 215°C
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Engine Oil Temperature
|
Engine oil temperature (estimated temperature)/
Min.: -40°C, Max.: 215°C
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Previous Trip Eng Oil Temp
|
Engine oil temperature during previous trip/
Min.: -40°C, Max.: 215°C
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Ambient Temp for A/C
|
Ambient temperature for A/C/
Min.: -40°C, Max.: 215°C
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Previous Trip Ambient Temp
|
Ambient temperature during previous trip/
Min.: -40°C, Max.: 215°C
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Engine Start Hesitation
|
History of hesitation during engine start/
ON or OFF
|
-
|
-
|
| Low Rev for Eng Start
|
History of low engine speed after engine start/
ON or OFF
|
-
|
-
|
| Minimum Engine Speed
|
Minimum engine speed/
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Fuel Cut Elps Time
|
Elapsed time since Fuel Cut due to high engine speed/
Min.: 0 sec, Max.: 68746 sec
|
-
|
The time elapsed after a fuel cut after high engine speed has occurred (More than the rpm at which fuel cut occurs + 500 rpm).
|
| Power Steering Pressure
|
Power steering oil pressure/
Min.: 0 MPa, Max.: 11 MPa
|
-
|
-
|
| ACT VSV
|
A/C cut status for Active Test/
ON or OFF
|
-
|
-
|
| Brake Override System
|
Brake override system status/
ON or OFF
|
ON: Brake override system operating
|
-
|
| Idle Fuel Cut
|
Fuel cut at idle/
ON or OFF
|
ON: Fuel cut operating
|
Idle Fuel Cut = "ON" when the throttle valve is fully closed and the engine speed is more than 2800 rpm.
|
| FC TAU
|
Fuel cut TAU (fuel cut during very light load)/
ON or OFF
|
ON: Fuel cut operating
|
The fuel cut being performed under a very light load to prevent the engine combustion from becoming incomplete.
|
| Immobiliser Fuel Cut
|
Status of immobiliser fuel cut/
ON or OFF
|
-
|
-
|
| Immobiliser Fuel Cut History
|
Status of the immobiliser fuel cut history/
ON or OFF
|
-
|
-
|
| Electrical Load Signal 1
|
Electrical load signal /
ON or OFF
|
ON: Headlight switch (Tail) on
|
-
|
| Cruise Main SW
|
Cruise control main switch
ON or OFF
|
-
|
-
|
| Cruise Cancel Signal
|
Status of the cruise cancel signal/
ON or OFF
|
-
|
-
|
| Model Code
|
Model code
|
-
|
Used for identifying the model code:
GRJ2##
|
| Engine Type
|
Engine type
|
-
|
Used for identifying the engine type:
1GRFE
|
| Cylinder Number
|
Number of cylinders/
Min.: 0, Max.: 255
|
-
|
Used for identifying the number of cylinders:
6
|
| Transmission Type
|
Transmission type
|
-
|
Used for identifying the transmission type:
MT, ECT 5th
|
| Transmission Type2
|
Transmission type 2
|
-
|
-
|
| Destination
|
Destination
|
-
|
Used for identifying the destination:
W
|
| Model Year
|
Model year/
Min.: 1900, Max.: 2155
|
-
|
Used for identifying the model year:
20##
|
| System Identification
|
System identification
|
-
|
Used for identifying the engine system:
Gasoline (gasoline engine)
|
| Engine Speed of Cyl #1
|
Engine speed for cylinder 1/
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
Output only when Check the Cylinder Compression is performed using the Active Test.
|
| Engine Speed of Cyl #2
|
Engine speed for cylinder 2/
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
Output only when Check the Cylinder Compression is performed using the Active Test.
|
| Engine Speed of Cyl #3
|
Engine speed for cylinder 3/
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
Output only when Check the Cylinder Compression is performed using the Active Test.
|
| Engine Speed of Cyl #4
|
Engine speed for cylinder 4/
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
Output only when Check the Cylinder Compression is performed using the Active Test.
|
| Engine Speed of Cyl #5
|
Engine speed for cylinder 5/
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
Output only when Check the Cylinder Compression is performed using the Active Test.
|
| Engine Speed of Cyl #6
|
Engine speed for cylinder 6/
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
Output only when Check the Cylinder Compression is performed using the Active Test.
|
| Av Engine Speed of All Cyl
|
Engine speed for all cylinders/
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
Output only when Check the Cylinder Compression is performed using the Active Test.
|
| SPD (NT)
|
Input shaft speed/
Min.: 0 rpm, Max.: 12750 rpm
|
·
Lock-up on (after warming up engine): Input turbine speed (NT) equal to engine speed
·
Lock-up off (idling with shift lever in N): Input turbine speed (NT) nearly equal to engine speed
|
Data is displayed in increments of 50 rpm.
|
| SPD (SP2)
|
Output shaft speed/
Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
|
Vehicle stopped: 0 km/h (0 mph) (output shaft speed equal to vehicle speed)
|
-
|
| Overdrive Cut Switch #1
|
Overdrive cut signal for cruise control/
ON or OFF
|
-
|
-
|
| Shift SW Status (P Range)
|
PNP switch status (P)/
ON or OFF
|
·
Shift lever not in P: OFF
|
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
| Pattern Switch (PWR/M)
|
Pattern switch (PWR) status/
ON or OFF
|
·
ON: Pattern switch (PWR) is pushed
·
OFF: Pattern switch (PWR) is not pushed
|
-
|
| Shift SW Status (R Range)
|
PNP switch status (R)/
ON or OFF
|
·
Shift lever not in R: OFF
|
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
| Shift SW Status (N Range)
|
PNP switch status (N)/
ON or OFF
|
·
Shift lever not in N: OFF
|
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
| Shift SW Status (N, P Range) Supported
|
Status of park/neutral position switch (N or P) supported/
Supp or Unsupp
|
-
|
-
|
| Shift SW Status (N, P Range)
|
Park/neutral position switch status (N or P)/
ON or OFF
|
·
ON: Shift lever not in P or N
·
OFF: Shift lever in P or N
|
-
|
| Sports Shift Up SW
|
Sport shift up switch status/
ON or OFF
|
·
ON: Shift lever held in "+" (up-shift)
·
OFF: Shift lever not in "+" (up-shift)
|
-
|
| Sports Shift Down SW
|
Sport shift down switch status/
ON or OFF
|
·
ON: Shift lever held in "-" (down-shift)
·
OFF: Shift lever not in "-" (down-shift)
|
-
|
| Sports Mode Selection SW
|
Sport mode select switch status/
ON or OFF
|
·
ON: Shift lever in S, "+" or "-"
·
OFF: Shift lever not in S, "+" or "-"
|
-
|
| Shift SW Status (D Range)
|
PNP switch status (D)/
ON or OFF
|
·
Shift lever in D, S, "+" or "-": ON
·
Shift lever not in D, S, "+" or "-": OFF
|
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
| A/T Oil Temperature 1
|
No. 1 ATF temperature sensor value/
Min.: -40°C, Max.: 150°C
|
·
After stall test:
Approximately 80°C (176°F)
·
Equal to ambient temperature when engine cold
|
If the value is -40°C (-40°F) or 150°C (302°F), the No. 1 ATF temperature sensor circuit is open or shorted.
|
| A/T Oil Temperature 2
|
No. 2 ATF temperature sensor value/
Min.: -40°C, Max.: 150°C
|
·
After stall test:
Approximately 80°C (176°F)
·
Equal to ambient temperature when engine cold
|
If the value is -40°C (-40°F) or 150°C (302°F), the No. 2 ATF temperature sensor circuit is open or shorted.
|
| ATF Thermal Degradation Estimate
|
Estimated value of ATF thermal degradation/
Min.: 0, Max.: 65535
|
-
|
If 50000 or more is displayed for the Data List item "ATF Thermal Degradation Estimate", thermal degradation of the ATF is suspected.
Perform ATF Thermal Degradation Estimate Reset after replacing the ATF.
|
| Lock Up
|
Lock-up/
ON or OFF
|
·
Lock-up not operating: OFF
|
-
|
| Shift Status
|
ECM gear shift command/
1st, 2nd, 3rd, 4th or 5th
|
Shift lever in D or S: 1st, 2nd, 3rd, 4th or 5th
|
-
|
| SLT Solenoid Status
|
Shift solenoid SLT status/
ON or OFF
|
·
Accelerator pedal depressed: OFF
·
Accelerator pedal released: ON
|
-
|
| SLU Solenoid Status
|
Shift solenoid SLU status/
ON or OFF
|
·
Shift solenoid operating: ON
·
Shift solenoid not operating: OFF
|
-
|
| Snow or 2nd Start Mode
|
Pattern switch (2nd) status/
ON or OFF
|
|
-
|