Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052774 1GR-FE ENGINE CONTROL _0255001 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0412  Secondary Air Injection System Switching Valve "A" Circuit  


DESCRIPTION

The secondary air injection system injects air into the exhaust port of the cylinder head using an electric air pump, starting when the engine is started cold and operating until the catalyst warms up, in order to promote combustion of unburned fuel and decrease the amount of hydrocarbons (HC) and carbon monoxide (CO) in the exhaust gas.

A217752E06
3.306,0.35 3.777,0.523 0.471,0.173 10 ECM 1.955,0.91 2.858,1.265 0.903,0.354 10 Air Injection Control Driver 0.18,1.802 2.072,2.020 1.893,0.218 10 Pressure Sensor (for Bank 1) 0.406,2.706 1.386,3.049 0.980,0.342 10 No. 1 Emission Control Valve 5.781,2.964 7.059,3.163 1.278,0.199 10 Air Pump Assembly 0.062,4.838 1.339,5.218 1.277,0.379 10 Heated Oxygen Sensor (for Bank 1) 0.048,3.907 1.403,4.265 1.355,0.358 10 Air Fuel Ratio Sensor (for Bank 1) 3.681,0.986 4.133,1.178 0.452,0.192 10 Relay 5.267,0.965 6.387,1.295 1.119,0.330 10 Pressure Sensor (for Bank 2) 5.733,3.345 6.738,3.732 1.005,0.387 10 No. 2 Emission Control Valve 5.859,5.239 7.109,5.582 1.250,0.343 10 Heated Oxygen Sensor (for Bank 2) 5.859,4.467 7.128,4.812 1.268,0.345 10 Air Fuel Ratio Sensor (for Bank 2) 4.119,1.071 4.288,1.071 false 5.216,1.015 5.132,1.015 5.132,1.015 4.719,2.505 false 2.072,1.897 2.337,1.897 2.337,1.897 2.561,2.505 false 1.427,2.794 1.84,2.794 false 1.536,3.988 1.397,3.988 false 1.536,4.934 1.28,4.934 false 5.658,3.404 5.558,3.404 5.558,3.404 5.279,3.205 false 5.812,4.545 5.714,4.545 5.714,4.545 5.574,3.984 false 5.812,5.302 5.644,5.302 5.644,5.302 5.553,4.938 false 6.426,2.941 6.426,2.773 false

DTC No. DTC Detection Condition Trouble Area
P0412 All conditions are met for 3 seconds or more while idling immediately after the engine is started (1 trip detection logic):
·

Secondary air injection system is not operating (the air pump and emission control valve are off).

·

Diagnostic signal from the air injection control driver has a duty cycle of 40% (this indicates an open in the emission control valve circuit).

·

Battery voltage is 8 V or higher.


·

Open in emission control valve drive circuit

·

Air injection control driver assembly

·

No. 1 emission control valve set

·

ECM


P0412 All conditions are met for 3 seconds or more while idling immediately after the engine is started (1 trip detection logic):
·

Secondary air injection system is operating (the air pump and emission control valve are on).

·

Diagnostic signal from the air injection control driver has a duty cycle of 40% (this indicates a short in the emission control valve circuit).

·

Battery voltage is 8 V or higher.


·

Short between emission control valve drive circuit and body ground

·

Air injection control driver assembly

·

No. 1 emission control valve set

·

ECM



MONITOR DESCRIPTION

This DTC indicates an open or short circuit in the circuit containing the emission control valve of the secondary air injection system. The air injection control driver performs diagnosis of the air pump assembly, emission control valve set and itself, and sends the results of this diagnosis to the ECM as a duty signal. When the ECM receives a signal indicating a malfunction in the air pump, emission control valve set or air injection control driver, it illuminates the MIL and stores a DTC.

WIRING DIAGRAM

A266664E02
0.09,0.024 0.926,0.236 0.836,0.211 12 for Bank 1: 0.7,1.057 0.940,1.241 0.239,0.184 10 1B 0.745,0.879 0.866,1.052 0.121,0.173 10 3 2.437,1.056 2.676,1.239 0.239,0.184 10 1B 2.491,0.877 2.612,1.050 0.121,0.173 10 2 2.441,1.687 2.680,1.871 0.239,0.184 10 1B 2.479,1.509 2.601,1.682 0.121,0.173 10 4 0.695,1.687 0.934,1.871 0.239,0.184 10 1C 0.747,1.509 0.869,1.682 0.121,0.173 10 1 1.001,1.805 1.643,1.952 0.642,0.147 10 EFI MAIN 2.829,1.805 3.495,1.962 0.666,0.157 10 EFI NO. 2 1.864,2.005 2.125,2.159 0.262,0.154 10 EFI 1.115,2.295 2.219,2.463 1.104,0.169 10 Integration Relay 3.816,1.688 4.097,1.838 0.281,0.150 10 C61 3.901,1.514 4.002,1.672 0.100,0.158 10 5 5.116,1.688 5.397,1.838 0.281,0.150 10 C61 5.201,1.514 5.301,1.672 0.100,0.158 10 2 4.131,1.688 4.336,1.837 0.205,0.149 10 +B 5.954,1.054 6.235,1.204 0.281,0.150 10 A38 5.995,0.88 6.176,1.038 0.181,0.158 10 34 6.275,1.054 6.700,1.203 0.425,0.149 10 MREL 5.946,1.688 6.227,1.838 0.281,0.150 10 C45 5.995,1.514 6.176,1.672 0.181,0.158 10 30 6.275,1.688 6.585,1.837 0.311,0.149 10 AIDI 5.95,2.322 6.231,2.472 0.281,0.150 10 C45 5.995,2.148 6.176,2.306 0.181,0.158 10 28 6.275,2.322 6.644,2.471 0.370,0.149 10 AIRV 5.95,2.956 6.231,3.106 0.281,0.150 10 C45 5.995,2.782 6.176,2.940 0.181,0.158 10 54 6.275,2.956 6.627,3.105 0.352,0.149 10 AIRP 5.95,4.918 6.231,5.067 0.281,0.150 10 A38 5.995,4.744 6.176,4.901 0.181,0.158 10 54 6.275,4.918 6.530,5.067 0.255,0.149 10 AIP 3.816,2.207 4.097,2.356 0.281,0.150 10 C60 3.901,2.033 4.002,2.190 0.100,0.158 10 1 4.131,2.207 4.506,2.356 0.375,0.149 10 BATT 3.816,2.728 4.097,2.878 0.281,0.150 10 C60 3.901,2.555 4.002,2.712 0.100,0.158 10 2 4.131,2.728 4.348,2.877 0.216,0.149 10 VP 3.816,3.252 4.097,3.401 0.281,0.150 10 C61 4.465,3.657 4.746,3.807 0.281,0.150 10 C61 3.901,3.078 4.002,3.235 0.100,0.158 10 1 4.323,3.657 4.423,3.815 0.100,0.158 10 6 4.131,3.252 4.258,3.400 0.127,0.149 10 E 4.501,3.486 4.723,3.639 0.222,0.152 10 VV 4.892,1.688 5.062,1.841 0.170,0.152 10 DI 5.116,2.319 5.397,2.468 0.281,0.150 10 C61 5.201,2.145 5.301,2.302 0.100,0.158 10 3 4.809,2.319 5.069,2.471 0.260,0.152 10 SIV 5.116,2.953 5.397,3.103 0.281,0.150 10 C61 5.201,2.78 5.301,2.937 0.100,0.158 10 4 4.809,2.953 5.061,3.106 0.252,0.152 10 SIP 4.823,3.661 5.712,3.980 0.889,0.319 10 Air Injection Control Driver 0.856,3.287 1.808,3.438 0.952,0.151 10 A/PUMP NO. 1 0.688,3.824 0.964,3.980 0.276,0.156 10 ALT 1.301,3.824 2.235,3.975 0.934,0.151 10 AI-PUMP HTR 1.368,4.454 2.235,4.605 0.867,0.151 10 AI-PMP HTR 2.335,4.048 2.440,4.204 0.105,0.156 10 2 2.924,4.048 3.028,4.204 0.105,0.156 10 5 2.335,4.828 2.440,4.984 0.105,0.156 10 1 2.76,5.888 2.865,6.044 0.105,0.156 10 1 3.318,5.888 3.423,6.044 0.105,0.156 10 2 2.76,6.686 2.865,6.842 0.105,0.156 10 3 3.318,6.686 3.423,6.842 0.105,0.156 10 4 2.924,4.828 3.028,4.984 0.105,0.156 10 3 0.663,6.72 1.138,6.895 0.475,0.174 10 Battery 2.05,6.201 2.424,6.366 0.373,0.165 10 C139 2.05,6.35 2.664,6.529 0.614,0.179 10 Air Pump 4.499,4.691 4.711,4.847 0.213,0.156 10 +B 4.647,4.445 4.756,4.601 0.110,0.156 10 5 4.782,4.919 5.040,5.073 0.258,0.154 10 AIP 5.137,4.818 5.244,4.986 0.107,0.167 10 3 5.942,5.567 6.223,5.716 0.281,0.150 10 C45 5.995,5.389 6.176,5.546 0.181,0.158 10 66 6.275,5.563 6.676,5.712 0.401,0.149 10 VCV2 4.806,5.564 5.040,5.718 0.235,0.154 10 VC 5.137,5.463 5.244,5.631 0.107,0.167 10 2 5.94,6.227 6.221,6.377 0.281,0.150 10 C45 5.995,6.053 6.176,6.211 0.181,0.158 10 98 6.275,6.227 6.683,6.376 0.408,0.149 10 ETHA 5.95,7.638 6.231,7.787 0.281,0.150 10 C45 5.995,7.464 6.176,7.621 0.181,0.158 10 61 6.275,7.638 6.622,7.787 0.348,0.149 10 HAI1 4.829,6.229 5.040,6.382 0.211,0.154 10 E2 5.137,6.128 5.244,6.296 0.107,0.167 10 4 4.444,6.448 4.781,6.609 0.336,0.161 10 GND 4.479,6.691 4.584,6.856 0.105,0.165 10 1 4.773,6.686 5.142,6.847 0.369,0.161 10 C137 4.773,6.85 5.888,7.178 1.115,0.328 10 No. 1 Emission Control Valve Set 6.502,8.217 6.838,8.387 0.336,0.170 10 ECM

CAUTION / NOTICE / HINT

HINT:
·

By using the GTS to perform the Secondary Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT NO. 1 EMISSION CONTROL VALVE SET
a.


OK

2.CHECK HARNESS AND CONNECTOR (NO. 1 EMISSION CONTROL VALVE SET - BODY GROUND)

NG

2.CHECK HARNESS AND CONNECTOR (NO. 1 EMISSION CONTROL VALVE SET - BODY GROUND)
a.

Disconnect the No. 1 emission control valve set connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C137-1 (GND) - Body ground Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 EMISSION CONTROL VALVE SET - AIR INJECTION CONTROL DRIVER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (NO. 1 EMISSION CONTROL VALVE SET - AIR INJECTION CONTROL DRIVER ASSEMBLY)
a.

Disconnect the No. 1 emission control valve set connector.


b.

Disconnect the air injection control driver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C137-5 (+B) - C61-6 (VV) Always Below 1 Ω
C137-5 (+B) or C61-6 (VV) - Body ground Always 10 kΩ or higher




OK

REPLACE AIR INJECTION CONTROL DRIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR