Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052774 1GR-FE ENGINE CONTROL _0255001 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0416  Secondary Air Injection System Switching Valve "B" Circuit Open  P0417  Secondary Air Injection System Switching Valve "B" Circuit Shorted  


DESCRIPTION

The ECM operates the air injection VSV relay (AI-VSV) which causes the No. 2 emission control valve to operate.

DTC No. DTC Detection Condition Trouble Area
P0416 Open or short in the air injection VSV relay (AI-VSV) circuit for 3 seconds (1 trip detection logic).
·

Open or short in air injection VSV relay (AI-VSV) circuit

·

Air injection VSV relay (AI-VSV)

·

ECM


P0417 Open or short in the air injection VSV relay (AI-VSV) circuit for 3 seconds (1 trip detection logic).
·

Open or short in air injection VSV relay (AI-VSV) circuit

·

Air injection VSV relay (AI-VSV)

·

ECM



MONITOR DESCRIPTION

These DTCs are designed to detect a malfunction in the air injection VSV (AI-VSV) relay circuit. When the system is normal, the battery voltage is applied to terminal AIR1 of the ECM while the air injection VSV (AI-VSV) relay is turned off, and the battery voltage is not applied to terminal AIR1 of the ECM while the air injection VSV (AI-VSV) relay is turned on. The ECM illuminates the MIL and stores a DTC when either one of the following conditions is detected.

·

The battery voltage is not applied to terminal AIR1 while the air injection VSV (AI-VSV) relay is off.

·

The battery voltage is applied to terminal AIR1 while the air injection VSV (AI-VSV) relay is on.


WIRING DIAGRAM

A266665E02
0.066,0.05 0.902,0.262 0.836,0.211 12 for Bank 2: 0.648,1.209 0.888,1.393 0.239,0.184 10 1B 0.693,1.031 0.814,1.204 0.121,0.173 10 3 2.385,1.207 2.624,1.391 0.239,0.184 10 1B 2.439,1.029 2.560,1.202 0.121,0.173 10 2 2.389,1.839 2.628,2.023 0.239,0.184 10 1B 2.427,1.66 2.548,1.834 0.121,0.173 10 4 0.643,1.839 0.882,2.023 0.239,0.184 10 1C 0.695,1.66 0.817,1.834 0.121,0.173 10 1 0.949,1.957 1.591,2.104 0.642,0.147 10 EFI MAIN 2.898,1.957 3.565,2.114 0.666,0.157 10 EFI NO. 2 1.812,2.157 2.073,2.310 0.262,0.154 10 EFI 1.063,2.446 2.167,2.615 1.104,0.169 10 Integration Relay 5.902,1.206 6.183,1.356 0.281,0.150 10 A38 5.943,1.032 6.124,1.190 0.181,0.158 10 34 6.223,1.206 6.648,1.355 0.425,0.149 10 MREL 5.894,1.84 6.175,1.990 0.281,0.150 10 C45 5.943,1.666 6.124,1.824 0.181,0.158 10 60 6.223,1.84 6.557,1.989 0.334,0.149 10 AIR1 5.896,3.945 6.177,4.095 0.281,0.150 10 A38 5.937,3.771 6.118,3.929 0.181,0.158 10 53 6.217,3.945 6.557,4.094 0.340,0.149 10 AIP2 1.512,4.172 1.789,4.327 0.276,0.156 10 ALT 2.068,3.236 3.001,3.387 0.934,0.151 10 AI-PUMP HTR 4.987,1.747 5.092,1.903 0.105,0.156 10 2 4.209,1.747 4.314,1.903 0.105,0.156 10 1 4.987,2.395 5.092,2.550 0.105,0.156 10 3 4.209,2.395 4.314,2.550 0.105,0.156 10 5 0.631,5.044 1.106,5.218 0.475,0.174 10 Battery 4.474,3.719 4.761,3.875 0.287,0.156 10 +BL 4.662,3.472 4.772,3.628 0.110,0.156 10 5 4.712,3.947 5.061,4.100 0.348,0.154 10 AIP2 5.159,3.846 5.266,4.014 0.107,0.167 10 3 5.884,4.598 6.165,4.748 0.281,0.150 10 C45 5.937,4.416 6.118,4.574 0.181,0.158 10 66 6.213,4.598 6.613,4.747 0.401,0.149 10 VCV2 4.757,4.592 5.061,4.745 0.304,0.154 10 VC2 5.159,4.491 5.266,4.658 0.107,0.167 10 2 5.892,5.255 6.173,5.405 0.281,0.150 10 C45 5.937,5.081 6.118,5.239 0.181,0.158 10 98 6.217,5.255 6.622,5.404 0.405,0.149 10 ETHA 4.764,5.257 5.061,5.410 0.297,0.154 10 E22 5.159,5.156 5.266,5.323 0.107,0.167 10 4 4.412,5.476 4.833,5.637 0.421,0.161 10 GNDL 4.484,5.719 4.589,5.884 0.105,0.165 10 1 4.778,5.714 5.147,5.875 0.369,0.161 10 C138 4.778,5.878 5.902,6.198 1.123,0.320 10 No. 2 Emission Control Valve Set 6.449,5.731 6.786,5.901 0.336,0.170 10 ECM 4.404,2.792 4.893,2.937 0.489,0.145 10 AI-VSV

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT AIR INJECTION VSV RELAY (AI-VSV)
a.

Inspect the air injection VSV relay (AI-VSV) (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

2.CHECK AIR INJECTION VSV RELAY (AI-VSV) (POWER SOURCE)

NG

REPLACE AIR INJECTION VSV RELAY (AI-VSV)

2.CHECK AIR INJECTION VSV RELAY (AI-VSV) (POWER SOURCE)
a.

Remove the air injection VSV relay (AI-VSV).


b.
A276696E02
0.144,0.082 0.337,0.265 0.193,0.184 10 *1 0.492,3.442 0.676,3.607 0.184,0.165 10 *2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Air injection VSV relay (AI-VSV) terminal 1 - Body ground Ignition switch ON 11 to 14 V
Air injection VSV relay (AI-VSV) terminal 5 - Body ground Always 11 to 14 V


Text in Illustration
*1 Engine Room Relay Block
*2 Air Injection VSV Relay (AI-VSV)



OK

3.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION VSV RELAY (AI-VSV))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION VSV RELAY (AI-VSV))
a.

Remove the air injection VSV relay (AI-VSV).


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Air injection VSV relay (AI-VSV) terminal 2 - C45-60 (AIR1) Always Below 1 Ω
Air injection VSV relay (AI-VSV) terminal 2 or C45-60 (AIR1) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR