Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › RELAY › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052774 1GR-FE ENGINE CONTROL _0255016 RELAY G

1GR-FE ENGINE CONTROL  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT AIR PUMP HEATER RELAY (AI-PMP HTR)

a.
A184106E13
2.542,1.104 2.938,1.104 false 2.542,1.615 2.948,1.615 false 1.573,0.177 1.698,0.177 1.698,0.177 2.031,0.563 false 3.031,0.177 2.906,0.177 2.906,0.177 2.625,0.552 false 0.208,0.729 0.417,0.906 0.208,0.177 10 false 3 1.208,0.729 1.406,0.906 0.198,0.177 10 false 5 0.208,1.271 0.365,1.448 0.156,0.177 10 false 2 1.208,1.271 1.438,1.448 0.229,0.177 10 false 1 3.021,1.521 3.229,1.698 0.208,0.177 10 false 3 3,1.021 3.198,1.198 0.198,0.177 10 false 5 3.094,0.083 3.25,0.26 0.156,0.177 10 false 2 1.417,0.083 1.646,0.26 0.229,0.177 10 false 1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 2.INSPECT AIR INJECTION VSV RELAY (AI-VSV)

a.
A184106E14
2.542,1.104 2.938,1.104 false 2.542,1.615 2.948,1.615 false 1.573,0.177 1.698,0.177 1.698,0.177 2.031,0.563 false 3.031,0.177 2.906,0.177 2.906,0.177 2.625,0.552 false 0.208,0.729 0.417,0.906 0.208,0.177 10 false 3 1.208,0.729 1.406,0.906 0.198,0.177 10 false 5 0.208,1.271 0.365,1.448 0.156,0.177 10 false 2 1.208,1.271 1.438,1.448 0.229,0.177 10 false 1 3.021,1.521 3.229,1.698 0.208,0.177 10 false 3 3,1.021 3.198,1.198 0.198,0.177 10 false 5 3.094,0.083 3.25,0.26 0.156,0.177 10 false 2 1.417,0.083 1.646,0.26 0.229,0.177 10 false 1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 3.INSPECT INTEGRATION RELAY (IG2)

a.

Measure the resistance of the IG2 MAIN fuse.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IG2 MAIN fuse Always Below 1 Ω


If the result is not as specified, replace the IG2 MAIN fuse.



b.

Measure the resistance of the ignition relay No. 2 (IG2) circuit.

i.
U162820E02
0.5,2.615 0.708,2.802 0.208,0.188 10 false 1C 1.396,2.625 1.615,2.833 0.219,0.208 10 false 1B 0.052,0 0.25,0.177 0.198,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1B-8 Battery voltage is not applied to terminals 1B-6 and 1B-7 10 kΩ or higher
Battery voltage is applied to terminals 1B-6 and 1B-7 Below 1 Ω


Text in Illustration
*a Component without harness connected
(Integration Relay)

If the result is not as specified, replace the integration relay.



Hide 4.INSPECT INTEGRATION RELAY (EFI)

a.

Measure the resistance of the EFI MAIN fuse.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI MAIN fuse Always Below 1 Ω


If the result is not as specified, replace the EFI MAIN fuse.



b.

Measure the resistance of the EFI relay circuit.

i.
U162820E02
0.5,2.615 0.708,2.802 0.208,0.188 10 false 1C 1.396,2.625 1.615,2.833 0.219,0.208 10 false 1B 0.052,0 0.25,0.177 0.198,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1B-4 Battery voltage is not applied to terminals 1B-2 and 1B-3 10 kΩ or higher
Battery voltage is applied to terminals 1B-2 and 1B-3 Below 1 Ω


Text in Illustration
*a Component without harness connected
(Integration Relay)

If the result is not as specified, replace the integration relay.



Hide 5.INSPECT EFI NO. 2 RELAY (EFI NO. 2)

a.
A184106E15
2.531,1.135 2.927,1.135 false 2.531,1.635 2.938,1.635 false 1.563,0.188 1.688,0.188 1.688,0.188 2.021,0.563 false 3.042,0.188 2.917,0.188 2.917,0.188 2.635,0.573 false 0.219,0.708 0.427,0.885 0.208,0.177 10 false 3 1.198,0.708 1.396,0.885 0.198,0.177 10 false 5 0.219,1.25 0.375,1.427 0.156,0.177 10 false 2 1.198,1.26 1.427,1.438 0.229,0.177 10 false 1 2.979,1.552 3.188,1.729 0.208,0.177 10 false 3 2.969,1.042 3.167,1.219 0.198,0.177 10 false 5 3.094,0.104 3.25,0.281 0.156,0.177 10 false 2 1.417,0.135 1.646,0.313 0.229,0.177 10 false 1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 6.INSPECT INTEGRATION RELAY (A/F)

a.

Measure the resistance of the A/F fuse.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A/F fuse Always Below 1 Ω


If the result is not as specified, replace the A/F fuse.



b.

Measure the resistance of the A/F sensor heater relay circuit.

i.
U162820E03
0.5,2.625 0.708,2.813 0.208,0.188 10 false 1C 1.375,2.625 1.594,2.833 0.219,0.208 10 false 1B 0.052,0 0.25,0.177 0.198,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1A-4 Battery voltage is not applied to terminals 1A-2 and 1A-3 10 kΩ or higher
Battery voltage is applied to terminals 1 A-2 and 1A-3 Below 1 Ω


Text in Illustration
*a Component without harness connected
(Integration Relay)

If the result is not as specified, replace the integration relay.



Hide 7.INSPECT MAIN BODY ECU (IG1 NO. 1)

A385663E01
1.427,2.281 1.427,3.063 true 2.448,1.479 2.698,1.677 2.698,1.677 2.698,3.052 true 3.125,1.771 3.125,3.052 true 4.052,4.604 4.156,4.792 4.156,4.792 4.156,5.396 true 0.125,0.073 0.438,0.271 0.313,0.198 10 false *a 3.031,0.854 3.385,1.052 0.354,0.198 10 false 2B 1.688,1.615 2.042,1.813 0.354,0.198 10 false 2A 1.385,3.083 1.74,3.281 0.354,0.198 10 false 1 2.625,3.083 2.979,3.281 0.354,0.198 10 false 17 3.094,3.083 3.438,3.281 0.344,0.198 10 false 5 3.635,3.844 3.99,4.042 0.354,0.198 10 false 2D 4.094,5.427 4.448,5.625 0.354,0.198 10 false 43

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2A-1 - 2B-17 Battery voltage is not applied to terminals 2B-5 and 2D-43 10 kΩ or higher
Battery voltage is applied to terminals 2B-5 and 2D-43 Below 1 Ω


Text in Illustration
*a Component without harness connected
(Main Body ECU)

If the result is not as specified, replace the cowl side junction block LH.


Hide 28300D 9.INSPECT STARTER CUT RELAY (ST CUT)

Hide 82733A 10.INSPECT MAIN BODY ECU (ACC RELAY)