Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › HEATED OXYGEN SENSOR › from 2015.08
RM2660E _51 Engine / Hybrid System _052774 1GR-FE ENGINE CONTROL _0255007 HEATED OXYGEN SENSOR A

1GR-FE ENGINE CONTROL  HEATED OXYGEN SENSOR  INSTALLATION  


PROCEDURE

Hide 89465 1.INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)

a.
A158663

Temporarily install the sensor to the exhaust pipe by hand.


b.
U163041E02
1.521,1.083 1.073,1.271 1.073,1.271 1.073,1.615 true 1.729,0.844 1.958,0.292 true 2.302,1.813 2.583,1.104 true 2.01,0.448 2.458,1.115 false 0.979,1.667 1.448,1.906 0.469,0.24 10 true SST 2.219,0.177 3.365,0.656 1.146,0.479 10 true Fulcrum Length

Using SST, tighten the sensor.

SST
09224-00010  

Torque:
without SST : 44 N*m (449 kgf*cm, 32 ft.*lbf)
with SST : 40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:
·

Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). If using a torque wrench with a length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Make sure SST and the wrench are connected in a straight line.




c.
A183479E02
0.073,0.052 2.469,0.49 2.396,0.438 12 true for Manual Transmission: 0.073,2.271 2.729,2.719 2.656,0.448 12 true for Automatic Transmission:

Connect the sensor connector.


Hide 89465A 2.INSTALL HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)

a.
A158663

Temporarily install the sensor to the exhaust pipe by hand.


b.
A175735E01
1.962,0.108 2.971,0.252 1.009,0.144 10 Fulcrum Length 1.52,1.705 1.813,1.855 0.293,0.151 10 SST 1.42,1.153 1.42,1.787 1.42,1.787 1.497,1.787 false

Using SST, tighten the sensor.

SST
09224-00010  

Torque:
without SST : 44 N*m (449 kgf*cm, 32 ft.*lbf)
with SST : 40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:
·

Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). If using a torque wrench with a length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Make sure SST and the wrench are connected in a straight line.




Hide 17450B 3.INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY

a.

Install 2 new gaskets to the front No. 2 exhaust pipe.


b.
A175747

Connect the front No. 2 exhaust pipe to the exhaust manifold LH with 2 new nuts.

Torque:
54 N*m (554 kgf*cm, 40 ft.*lbf)


c.

Connect the front No. 2 exhaust pipe to the center exhaust pipe with the 2 bolts.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)


d.
A183478E02
0.063,0.052 2.427,0.417 2.365,0.365 12 true for Manual Transmission: 0.063,2.344 2.583,2.75 2.521,0.406 12 true for Automatic Transmission:

Connect the heated oxygen sensor connector.

HINT:

Hook the wire harness to the bracket.