Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › RELAY › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0255031 RELAY G

3UR-FE ENGINE CONTROL  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT INTEGRATION RELAY (IG2)

a.

Measure the resistance of the IG2 MAIN fuse.

i.

Remove the IG2 MAIN fuse from the integration relay.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IG2 MAIN fuse Always Below 1 Ω


If the result is not as specified, replace the IG2 MAIN fuse.


iii.

Install the IG2 MAIN fuse to the integration relay.



b.
U163348E02
0.448,1.625 0.677,1.802 0.229,0.177 10 false 1C 1.292,1.615 1.51,1.781 0.219,0.167 10 false 1B 0.115,0.094 0.344,0.323 0.229,0.229 10 false *a

Measure the resistance of the ignition relay No. 2 (IG2) circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1B-8 Battery voltage is not applied to terminals 1B-6 and 1B-7 10 kΩ or higher
Battery voltage is applied to terminals 1B-6 and 1B-7 Below 1 Ω


Text in Illustration
*a Component without harness connected
(Integration Relay)

If the result is not as specified, replace the integration relay.



Hide 2.INSPECT INTEGRATION RELAY (EFI)

a.

Measure the resistance of the EFI MAIN fuse.

i.

Remove the EFI MAIN fuse from the integration relay


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI MAIN fuse Always Below 1 Ω


If the result is not as specified, replace the EFI MAIN fuse.


iii.

Install the EFI MAIN fuse to the integration relay.



b.
U163348E02
0.448,1.625 0.677,1.802 0.229,0.177 10 false 1C 1.292,1.615 1.51,1.781 0.219,0.167 10 false 1B 0.115,0.094 0.344,0.323 0.229,0.229 10 false *a

Measure the resistance of the EFI relay circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1B-4 Battery voltage is not applied to terminals 1B-2 and 1B-3 10 kΩ or higher
Battery voltage is applied to terminals 1B-2 and 1B-3 Below 1 Ω


Text in Illustration
*a Component without harness connected
(Integration Relay)

If the result is not as specified, replace the integration relay.



Hide 3.INSPECT EFI NO. 2 RELAY

a.
A188757E01
0.335,0.748 0.453,0.907 0.118,0.159 10 5 0.335,1.276 0.453,1.435 0.118,0.159 10 1 1.65,0.61 1.768,0.769 0.118,0.159 10 1 1.278,0.748 1.396,0.907 0.118,0.159 10 3 1.278,1.276 1.396,1.435 0.118,0.159 10 2 3.13,0.61 3.248,0.769 0.118,0.159 10 2 1.775,0.708 2.117,0.708 false 2.768,0.716 3.098,0.716 false 3.13,0.992 3.248,1.151 0.118,0.159 10 5 2.663,1.099 3.098,1.099 false 3.13,1.487 3.248,1.645 0.118,0.159 10 3 2.663,1.593 3.098,1.593 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 4.INSPECT INTEGRATION RELAY (A/F)

a.

Measure the resistance of the A/F fuse.

i.

Remove the A/F fuse from the integration relay.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A/F fuse Always Below 1 Ω


If the result is not as specified, replace the A/F fuse.


iii.

Install the A/F fuse to the integration relay.



b.
U163349E02
2.438,1.625 2.667,1.802 0.229,0.177 10 false 1A 0.406,1.625 0.625,1.802 0.219,0.177 10 false 1C 0.115,0.083 0.344,0.313 0.229,0.229 10 false *a

Measure the resistance of the A/F sensor heater relay circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1A-4 Battery voltage is not applied to terminals 1A-2 and 1A-3 10 kΩ or higher
Battery voltage is applied to terminals 1 A-2 and 1A-3 Below 1 Ω


Text in Illustration
*a Component without harness connected
(Integration Relay)

If the result is not as specified, replace the integration relay.



Hide 5.INSPECT MAIN BODY ECU (IG1 NO. 1)

a.

Measure the resistance according to the value(s) in the table below.

A385663E01
1.427,2.281 1.427,3.063 true 2.448,1.479 2.698,1.677 2.698,1.677 2.698,3.052 true 3.125,1.771 3.125,3.052 true 4.052,4.604 4.156,4.792 4.156,4.792 4.156,5.396 true 0.125,0.073 0.438,0.271 0.313,0.198 10 false *a 3.031,0.854 3.385,1.052 0.354,0.198 10 false 2B 1.688,1.615 2.042,1.813 0.354,0.198 10 false 2A 1.385,3.083 1.74,3.281 0.354,0.198 10 false 1 2.625,3.083 2.979,3.281 0.354,0.198 10 false 17 3.094,3.083 3.438,3.281 0.344,0.198 10 false 5 3.635,3.844 3.99,4.042 0.354,0.198 10 false 2D 4.094,5.427 4.448,5.625 0.354,0.198 10 false 43

Text in Illustration
*a Component without harness connected
(Main Body ECU)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
2A-1 - 2B-17 Battery voltage is not applied to terminals 2B-5 and 2D-43 10 kΩ or higher
Battery voltage is applied to terminals 2B-5 and 2D-43 Below 1 Ω


If the result is not as specified, replace the main body ECU.


Hide 28300D 7.INSPECT STARTER CUT RELAY (ST CUT)