Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/o Secondary Air Injection System) › from 2015.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0255032 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P0120  Throttle / Pedal Position Sensor / Switch "A" Circuit Malfunction  P0122  Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input  P0123  Throttle / Pedal Position Sensor / Switch "A" Circuit High Input  P0220  Throttle / Pedal Position Sensor / Switch "B" Circuit  P0222  Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input  P0223  Throttle / Pedal Position Sensor / Switch "B" Circuit High Input  P2135  Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation  


CAUTION / NOTICE / HINT

DESCRIPTION

The TP sensor is mounted on the throttle body, and detects the opening angle of the throttle valve. This sensor is a non-contact type. It uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds.

The TP sensor has 2 sensor circuits, each of which transmits a signal, VTA1 and VTA2. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA terminals of the ECM.

As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air-fuel ratio correction, power increase correction and fuel cut control.

U163314E01
4.393,1.517 4.647,1.056 4.647,1.056 4.735,1.056 false 3.963,1.658 4.214,1.814 0.251,0.156 10 4.8 4.572,1.917 4.950,2.087 0.378,0.170 10 VTA2 4.968,2.706 5.346,2.876 0.378,0.170 10 VTA1 3.82,2.268 4.198,2.423 0.377,0.156 10 2.60* 3.893,2.408 4.194,2.564 0.302,0.156 10 2.25 3.837,2.744 4.194,2.900 0.357,0.156 10 0.97* 3.893,2.884 4.194,3.040 0.302,0.156 10 0.69 3.963,1.42 4.195,1.576 0.232,0.156 10 5.0 4.79,0.989 5.765,1.144 0.975,0.156 10 Fail-safe Angle 2.681,1.015 4.343,1.192 1.663,0.177 10 Sensor Output Voltage (V) 6.484,3.409 6.835,3.565 0.350,0.156 10 86° 4.351,3.122 4.528,3.278 0.177,0.156 10 7° 4.166,3.423 4.426,3.579 0.260,0.156 10 0° 1.965,1.136 2.308,1.304 0.343,0.168 10 ECM 1.306,1.749 1.726,1.905 0.420,0.156 10 VCTA 1.306,2.758 1.649,2.914 0.343,0.156 10 ETA 1.306,2.085 1.705,2.241 0.399,0.156 10 VTA1 1.306,2.414 1.705,2.570 0.399,0.156 10 VTA2 1.271,1.034 1.788,1.211 0.517,0.177 10 Magnet 1.397,3.479 1.914,3.656 0.517,0.177 10 Magnet 0.297,1.493 0.879,1.670 0.582,0.177 10 IC No. 1 0.297,3.147 0.891,3.323 0.593,0.177 10 IC No. 2 0.031,0.656 1.638,0.833 1.607,0.177 10 Throttle Position Sensor 0.071,3.707 0.512,3.870 0.441,0.163 10 Note: 0.071,4.025 3.394,4.367 3.323,0.343 10 The throttle valve opening angle detected by the sensor terminal VTA1 is expressed as a percentage. 0.071,4.777 3.433,4.961 3.362,0.185 10 Between 10% and 22%: Throttle valve fully closed 0.071,5.116 3.114,5.272 3.043,0.156 10 Between 64% and 96%: Throttle valve fully open 0.071,5.443 2.792,5.599 2.721,0.156 10 Approximately 19.4%: Fail-safe angle (7°) 0.834,1.578 0.89,2.2 false 1.249,1.099 0.925,1.9 false 0.889,2.942 1.362,3.561 false 0.865,2.581 0.475,3.129 false 4.034,0.452 5.718,0.636 1.684,0.184 10 Line indicating VTA2 x 0.8 5.715,0.536 5.883,0.536 5.883,0.536 6.144,1.853 false 5.895,2.512 6.357,2.728 0.461,0.216 10 1.11 V 5.1,3.675 7.136,3.876 2.036,0.201 10 Throttle Valve Opening Angle (°) 4.948,3.329 6.099,3.531 1.150,0.202 10 Usable Range 4.65,4.082 6.238,4.283 1.589,0.201 10 *: During fail-safe control 5.536,2.255 5.895,2.554 false 3.62,4.594 5.645,4.750 2.024,0.156 10 Characteristics of sensor output: 3.62,4.917 6.903,5.073 3.282,0.156 10 VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V. 5.536,2.34 5.536,2.153 false

DTC Code DTC Detection Condition Trouble Area
P0120 The output voltage of VTA1 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds when the accelerator pedal is depressed (1 trip detection logic).
·

Throttle Position (TP) sensor (built into throttle body)

·

ECM


P0122 The output voltage of VTA1 is 0.2 V or less for 2 seconds when the accelerator pedal is depressed (1 trip detection logic).
·

TP sensor (built into throttle body)

·

Short in VTA1 circuit

·

Open in VC circuit

·

ECM


P0123 The output voltage of VTA1 is 4.535 V or higher for 2 seconds when the accelerator pedal is depressed (1 trip detection logic).
·

TP sensor (built into throttle body)

·

Open in VTA1 circuit

·

Open in E2 circuit

·

Short between VC and VTA1 circuits

·

ECM


P0220 The output voltage of VTA2 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds when the accelerator pedal is depressed (1 trip detection logic).
·

TP sensor (built into throttle body)

·

ECM


P0222 The output voltage of VTA2 is 1.75 V or less for 2 seconds when the accelerator pedal is depressed (1 trip detection logic).
·

TP sensor (built into throttle body)

·

Short in VTA2 circuit

·

Open in VC circuit

·

ECM


P0223 The output voltage of VTA2 is 4.8 V or higher, and VTA1 is between 0.2 V and 2.02 V for 2 seconds when the accelerator pedal is depressed (1 trip detection logic).
·

TP sensor (built into throttle body)

·

Open in VTA2 circuit

·

Open in E2 circuit

·

Short between VC and VTA2 circuits

·

ECM


P2135 Either condition (a) or (b) is met (1 trip detection logic):
(a) The difference between the output voltages of VTA1 and VTA2 is 0.02 V or less for 0.5 seconds or more.
(b) The output voltage of VTA1 is 0.2 V or less and VTA2 is 1.75 V or less for 0.4 seconds or more.
·

Short between VTA1 and VTA2 circuits

·

TP sensor (built into throttle body)

·

ECM



HINT:
·

When any of these DTCs is output, check the throttle valve opening angle by entering the following menus: Powertrain / Engine and ECT / Data List / ETCS / Throttle Position No.1 and Throttle Position No.2.


·

Throttle Position No.1 is the VTA1 signal, and Throttle Position No.2 is the VTA2 signal.

Reference (Normal Condition):
Display Item Accelerator Pedal Fully Released Accelerator Pedal Fully Depressed
Throttle Position No.1 0.5 to 1.1 V 3.2 to 4.8 V
Throttle Position No.2 2.1 to 3.1 V 4.6 to 5.0 V




MONITOR DESCRIPTION

The ECM uses the Throttle Position (TP) sensor to monitor the throttle valve opening angle. There are several checks that the ECM performs to confirm the proper operation of the TP sensor.

·

A specific voltage difference is expected between the sensor terminals, VTA1 and VTA2, for each throttle valve opening angle. If the difference between VTA1 and VTA2 is incorrect, the ECM interprets this as a malfunction in the sensor, and stores DTC(s).


·

VTA1 and VTA2 each have a specific voltage range. If VTA1 or VTA2 is outside the normal operating range, the ECM interprets this as a malfunction in the sensor, and stores DTC(s).


·

VTA1 and VTA2 should never be close to the same voltage level. If VTA1 is within 0.02 V of VTA2, the ECM determines that there is a short circuit in the sensor, and stores DTC(s).


If the malfunction is not repaired successfully, a DTC is stored 10 seconds after the engine is next started.

FAIL-SAFE

When any of these DTCs, as well as other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 7° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

Fail-safe mode continues until a pass condition is detected, and the engine switch is then turned off.

WIRING DIAGRAM

A162761E13
0.125,2.729 0.375,2.938 0.25,0.208 10 false C3 0.125,2.885 4.76,3.135 4.635,0.25 10 false Throttle Position Sensor (Built into Throttle Body) 1.094,0.604 1.271,0.771 0.177,0.167 10 false IC 1.094,1.5 1.271,1.667 0.177,0.167 10 false IC 1.594,0.479 1.917,0.646 0.323,0.167 10 false VTA 1.667,1.031 1.938,1.208 0.271,0.177 10 false VC 1.521,1.552 1.938,1.729 0.417,0.177 10 false VTA2 1.677,2.146 1.917,2.313 0.24,0.167 10 false E2 5.583,0.458 6.031,0.625 0.448,0.167 10 false VTA1 5.573,1 6.01,1.188 0.438,0.188 10 false VCTA 5.583,1.552 5.969,1.74 0.385,0.188 10 false VTA2 5.594,2.115 5.938,2.302 0.344,0.188 10 false ETA 1.99,0.469 2.104,0.625 0.115,0.156 10 false 6 1.99,1.01 2.094,1.188 0.104,0.177 10 false 5 1.979,1.563 2.094,1.76 0.115,0.198 10 false 4 1.979,2.125 2.094,2.292 0.115,0.167 10 false 3 5.99,2.844 6.333,3.063 0.344,0.219 10 false C45 5.219,0.469 5.521,0.625 0.302,0.156 10 false 126 5.229,1.01 5.521,1.156 0.292,0.146 10 false 125 5.24,1.563 5.531,1.719 0.292,0.156 10 false 101 5.25,2.135 5.521,2.323 0.271,0.188 10 false 124 5.979,3 6.417,3.25 0.438,0.25 10 false ECM

CAUTION / NOTICE / HINT

HINT:
·

These DTCs relate to the Throttle Position (TP) sensor.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / ETCS / Throttle Position No.1 and Throttle Position No.2.


d.

Check the values displayed on the tester.

Result
TP#1 (VTA1)
When Accelerator Pedal Released
TP#2 (VTA2)
When Accelerator Pedal Released
TP#1 (VTA1)
When Accelerator Pedal Depressed
TP#2 (VTA2)
When Accelerator Pedal Depressed
Trouble Area Proceed to
0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V VC circuit open A
4.5 to 5.0 V 4.5 to 5.0 V 4.5 to 5.0 V 4.5 to 5.0 V E2 circuit open A
0 to 0.2 V,
or 4.5 to 5.0 V
2.1 to 3.1 V
(Fail-safe)
0 to 0.2 V,
or 4.5 to 5.0 V
2.1 to 3.1 V
(Fail-safe)
VTA1 circuit open or ground short A
0.6 to 1.4 V
(Fail-safe)
0 to 0.2 V,
or 4.5 to 5.0 V
0.6 to 1.4 V
(Fail-safe)
0 to 0.2 V,
or 4.5 to 5.0 V
VTA2 circuit open or ground short A
0.5 to 1.1 V 2.1 to 3.1 V 3.2 to 4.8 V
(Not fail-safe)
4.6 to 5.0 V
(Not fail-safe)
TP sensor circuit normal B


HINT:

TP#1 stands for Throttle Position No. 1, and TP#2 stands for Throttle Position No. 2.



A

2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)

B

5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
a.

Disconnect the C3 throttle body connector.


b.

Disconnect the C45 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C3-5 (VC) - C45-125 (VCTA) Always Below 1 Ω
C3-6 (VTA) - C45-126 (VTA1) Always Below 1 Ω
C3-4 (VTA2) - C45-101 (VTA2) Always Below 1 Ω
C3-3 (E2) - C45-124 (ETA) Always Below 1 Ω
C3-5 (VC) or C45-125 (VCTA) - Body ground Always 10 kΩ or higher
C3-6 (VTA) or C45-126 (VTA1) - Body ground Always 10 kΩ or higher
C3-4 (VTA2) or C45-101 (VTA2) - Body ground Always 10 kΩ or higher




OK

3.INSPECT ECM (VC VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (VC VOLTAGE)
U162821E01
0.045,0.01 2.384,0.361 2.338,0.351 10 Front view of wire harness connector: (to Throttle Body) 1.133,1.81 1.362,1.976 0.229,0.166 10 E2 2.153,1.81 2.382,1.976 0.229,0.166 10 VC 0.613,1.108 0.915,1.289 0.302,0.181 10 C3 1.304,1.783 1.622,1.401 false 2.222,1.805 1.969,1.396 false

a.

Disconnect the C3 throttle body connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C3-5 (VC) - C3-3 (E2) Engine switch on (IG) 4.5 to 5.5 V




OK

4.REPLACE THROTTLE BODY ASSEMBLY

NG

4.REPLACE THROTTLE BODY ASSEMBLY
a.

Replace the throttle body assembly (See page Engine / Hybrid System>3UR-FE (ENGINE CONTROL)>THROTTLE BODY>REMOVAL).



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester on.



d.

Start the engine.


e.

Allow the engine to idle for 15 seconds or more.


f.

Enter the following menus: Powertrain / Engine and ECT / DTC.


g.

Read DTCs.

Result
Result Proceed to
P0120, P0122, P0123, P0220, P0222, P0223 and/or P2135 are output A
No DTC is output B



A

B

SYSTEM OK