Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/o Secondary Air Injection System) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0255032 SFI SYSTEM(w/o Secondary Air Injection System) C

3UR-FE ENGINE CONTROL  SFI SYSTEM(w/o Secondary Air Injection System)  P0340  Camshaft Position Sensor Circuit Malfunction  P0342  Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)  P0343  Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)  P0345  Camshaft Position Sensor "A" Circuit (Bank 2)  P0347  Camshaft Position Sensor "A" Circuit Low Input (Bank 2)  P0348  Camshaft Position Sensor "A" Circuit High Input (Bank 2)  


DESCRIPTION

The intake camshaft Variable Valve Timing (VVT) sensor (VV1, 2 signal) consists of a magnet and MRE (Magnetic Resistance Element).

The intake camshaft has 3 teeth on its outer circumference. When the intake camshaft rotates, changes occur in the air gaps between the teeth and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the intake camshaft rotation data into pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.

The crankshaft position sensor plate has 34 teeth. The crankshaft position sensor generates 34 signals for each revolution. Based on a combination of the VVT signal and NE signal, the ECM detects the crankshaft angle. Then the ECM uses this data to control fuel injection time and injection timing. Also, based on the NE signal, the ECM detects the engine speed.

DTC Code DTC Detection Condition Trouble Area
P0340
P0345
When either condition below is met:
·

The input voltage to the ECM remains at below 0.3 V or higher than 4.7 V for 4 seconds when 2 or more seconds have elapsed after turning the engine switch on (IG) (1 trip detection logic).

·

No VVT sensor (for intake side of Bank 1, 2) signal is sent to the ECM during cranking (2 trip detection logic).


·

Open or short in VVT sensor (for intake side) circuit

·

VVT sensor (for intake side)

·

Intake camshaft (for Bank 1, 2)

·

Jumped tooth of timing chain

·

ECM


P0342
P0347
The output voltage of the VVT sensor (for intake side of Bank 1, 2) is below 0.3 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor (for intake side) circuit

·

VVT sensor (for intake side)

·

Intake camshaft (for Bank 1, 2)

·

Jumped tooth of timing chain

·

ECM


P0343
P0348
The output voltage of the VVT sensor (for intake side of Bank 1, 2) is higher than 4.7 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor (for intake side) circuit

·

VVT sensor (for intake side)

·

Intake camshaft (for Bank 1, 2)

·

Jumped tooth of timing chain

·

ECM



A149748E02
0.212,1.195 0.442,1.360 0.230,0.165 10 NE 0.139,1.682 0.443,1.833 0.304,0.151 10 VV1 0.143,2.063 0.442,2.209 0.299,0.145 10 VV2 2.845,1.258 3.181,1.407 0.336,0.149 10 GND 2.845,2.212 3.181,2.361 0.336,0.149 10 GND 2.845,1.829 3.181,1.978 0.336,0.149 10 GND 0.863,2.54 1.783,2.682 0.921,0.141 10 20 msec./DIV. 2.641,0.672 3.205,0.828 0.563,0.156 10 5 V/DIV. 0.277,0.109 2.594,0.265 2.318,0.156 10 VV1, VV2 and NE Signal Waveforms

Reference: Inspection using an oscilloscope

Standard:
Tester Connection Tool Setting Condition Specified Condition
C45-110 (NE+) - C45-111 (NE-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown
C45-92 (VV1+) - C45-91 (VV1-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown
C45-87 (VV2+) - C45-88 (VV2-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown


HINT:

VV1+ and VV2+ stand for the VVT sensor (for intake side) signal, and NE+ stands for the CKP sensor signal.



MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the engine revolving, or the rotations of the camshaft and the crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

WIRING DIAGRAM

A179606E09
0.601,3.896 1.254,4.073 0.654,0.177 10 C101 0.601,2.399 3.090,2.576 2.489,0.177 10 VVT Sensor (for Intake Side of Bank 1) 0.601,2.244 1.301,2.421 0.700,0.177 10 C100 0.601,4.051 3.091,4.228 2.490,0.177 10 VVT Sensor (for Intake Side of Bank 2) 1.536,1.194 1.758,1.347 0.222,0.152 10 VC 1.856,1.285 1.998,1.462 0.142,0.177 10 3 4.853,1.285 5.089,1.462 0.236,0.177 10 66 4.857,1.667 5.093,1.844 0.236,0.177 10 92 4.857,2.05 5.093,2.227 0.236,0.177 10 91 1.361,1.58 1.761,1.732 0.399,0.152 10 VVL+ 1.856,1.671 1.998,1.847 0.142,0.177 10 1 1.392,1.944 1.757,2.096 0.364,0.152 10 VVL- 5.135,1.194 5.606,1.347 0.471,0.152 10 VCV2 4.853,2.943 5.089,3.120 0.236,0.177 10 67 5.135,2.852 5.606,3.005 0.471,0.152 10 VCV1 5.135,1.58 5.534,1.732 0.399,0.152 10 VV1+ 5.135,1.946 5.495,2.137 0.360,0.192 10 VV1- 4.857,3.329 5.093,3.506 0.236,0.177 10 87 4.857,3.712 5.093,3.889 0.236,0.177 10 88 5.135,3.242 5.534,3.395 0.399,0.152 10 VV2+ 5.135,3.608 5.495,3.800 0.360,0.192 10 VV2- 1.856,2.035 1.998,2.212 0.142,0.177 10 2 1.536,2.841 1.758,2.993 0.222,0.152 10 VC 1.856,2.932 1.998,3.108 0.142,0.177 10 3 1.361,3.226 1.761,3.378 0.399,0.152 10 VVR+ 1.856,3.317 1.998,3.494 0.142,0.177 10 1 1.392,3.59 1.757,3.743 0.364,0.152 10 VVR- 1.856,3.681 1.998,3.858 0.142,0.177 10 2 5.33,4.244 5.663,4.400 0.333,0.156 10 C45 5.33,4.38 5.698,4.535 0.368,0.156 10 ECM

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE)
A385682E01
2,2.229 2.698,2.781 true 0.156,0.125 2.479,0.583 2.323,0.458 10 false Front view of wire harness connector: (to VVT Sensor) 0.24,1.594 0.729,1.75 0.49,0.156 10 false C100 0.229,1.917 0.719,2.073 0.49,0.156 10 false C101 0.656,1.5 1.146,1.656 0.49,0.156 10 false *1 0.667,1.802 1.156,1.958 0.49,0.156 10 false *2 2.729,2.74 3.219,2.896 0.49,0.156 10 false VC 0.146,2.635 1.021,2.875 0.875,0.24 10 false *1: for Bank 1 0.156,2.938 1.031,3.177 0.875,0.24 10 false *2: for Bank 2

a.

Disconnect the C100 or C101 VVT sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C100-3 (VC) - Body ground Engine switch on (IG) 4.5 to 5.0 V
C101-3 (VC) - Body ground Engine switch on (IG) 4.5 to 5.0 V




OK

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR INTAKE SIDE - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR INTAKE SIDE - ECM)
a.

Disconnect the C100 or C101 VVT sensor connector.

A385683E01
2.635,1.354 1.677,1.729 true 2.656,1.99 1.885,1.781 true 4.771,1.865 4.667,2.344 true 4.833,1.875 5.427,2.333 true 5.063,1.865 5.625,1.052 true 5.125,1.854 6.406,1.063 true 0.115,0.115 2.521,0.563 2.406,0.448 10 false Front view of wire harness connector: (to VVT Sensor) 0.604,1.469 1.021,1.656 0.417,0.188 10 false C100 0.604,1.76 1.021,1.948 0.417,0.188 10 false C101 0.958,1.406 1.375,1.594 0.417,0.188 10 false *1 0.969,1.688 1.385,1.875 0.417,0.188 10 false *2 4.177,0.115 6.583,0.563 2.406,0.448 10 false Front view of wire harness connector: (to ECM) 4.51,0.938 4.927,1.125 0.417,0.188 10 false C45 2.74,1.208 3.271,1.615 0.531,0.406 10 false VVL+*1 VVR+*2 2.74,1.938 3.271,2.344 0.531,0.406 10 false VVL-*1 VVR-*2 5.667,0.927 6.313,1.146 0.646,0.219 10 false 91 (VV1-) 6.438,0.927 7.083,1.146 0.646,0.219 10 false 92 (VV1+) 4.552,2.365 5.198,2.583 0.646,0.219 10 false 87 (VV2+) 5.344,2.365 5.99,2.583 0.646,0.219 10 false 88 (VV2-) 3.573,1.979 4.427,2.219 0.854,0.24 10 false *1: for Bank 1 3.573,2.271 4.427,2.51 0.854,0.24 10 false *2: for Bank 2


b.

Disconnect the C45 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C100-1 (VVL+) - C45-92 (VV1+) Always Below 1 Ω
C100-2 (VVL-) - C45-91 (VV1-) Always Below 1 Ω
C101-1 (VVR+) - C45-87 (VV2+) Always Below 1 Ω
C101-2 (VVR-) - C45-88 (VV2-) Always Below 1 Ω
C100-1 (VVL+) or C45-92 (VV1+) - Body ground Always 10 kΩ or higher
C100-2 (VVL-) or C45-91 (VV1-) - Body ground Always 10 kΩ or higher
C101-1 (VVR+) or C45-87 (VV2+) - Body ground Always 10 kΩ or higher
C101-2 (VVR-) or C45-88 (VV2-) - Body ground Always 10 kΩ or higher




OK

3.CHECK SENSOR INSTALLATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION
a.
A385403E02
0.49,1.781 0.802,1.979 0.313,0.198 10 false OK 1.688,1.552 2.354,1.771 0.667,0.219 10 false Clearance 2.646,1.781 2.958,1.979 0.313,0.198 10 false NG

Check the VVT sensor (for intake side) installation.

OK:

Sensor is installed correctly.




OK

4.CHECK INTAKE CAMSHAFT (TEETH)

NG

4.CHECK INTAKE CAMSHAFT (TEETH)
a.

Check the teeth of the camshaft.

OK:

Teeth do not have any cracks or deformation.




OK

5.REPLACE VVT SENSOR (for Intake Side)

NG

5.REPLACE VVT SENSOR (for Intake Side)
a.

Replace the VVT sensor (for Intake Side) (See page Engine / Hybrid System>3UR-FE (ENGINE CONTROL)>CAMSHAFT POSITION SENSOR>REMOVAL).



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS
6.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Clear DTCs.


e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / DTC.


g.

Read DTCs.

Result
Result Proceed to
No output A
P0340, P0342, P0343, P0345, P0347 or P0348 B

HINT:

If the engine does not start, replace the ECM.




A

END

B