Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/o Secondary Air Injection System) › 2015.08–2016.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0255032 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P0031  Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)  P0032  Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)  P0051  Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1)  P0052  Oxygen (A/F) Sensor Heater Control Circuit High (Bank 2 Sensor 1)  P101D  A/F Sensor Heater Circuit Performance Bank 1 Sensor 1 Stuck ON  P103D  A/F Sensor Heater Circuit Performance Bank 2 Sensor 1 Stuck ON  


DESCRIPTION

The A/F sensor generates a voltage* that corresponds to the actual air-fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air-fuel ratio. The ECM determines the deviation from the stoichiometric air-fuel ratio level, and regulates the fuel injection time. If the A/F sensor malfunctions, the ECM is unable to control the air-fuel ratio accurately.

The A/F sensor is the planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor in order to facilitate accurate airfuel ratio detection. In addition, the sensor and heater portions are the narrow type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, therefore the sensor activation is accelerated.

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC is used. For the most efficient use of the TWC, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.

*: Value changes inside the ECM. Since the A/F sensor is the current output element, a current is converted into a voltage inside the ECM. Any measurements taken at the A/F sensor or ECM connectors will show a constant voltage.

A337244E03
0.781,1.521 0.958,1.521 0.958,1.521 1.479,2.125 false 1.646,2.094 2.021,1.167 2.021,1.167 2.208,1.167 false 3.042,1.771 3.427,2.125 3.427,2.125 3.573,2.125 false 2.865,1.635 3.365,1.521 3.365,1.521 3,1.698 false 3.167,1.198 3.427,0.896 3.427,0.896 3.615,0.896 false 3.042,1.167 3.417,0.563 3.417,0.563 3.604,0.563 false 2.948,1.125 3.344,0.229 3.344,0.229 3.052,0.229 false 0.146,2.396 1.656,2.604 1.51,0.208 10 false Exhaust Gas 1.083,2.5 1.542,2.781 0.458,0.281 10 false A 1.813,2.51 2.271,2.792 0.458,0.281 10 false A 0.271,1.438 1.646,1.635 1.375,0.198 10 false Element 2.25,1.094 3.625,1.292 1.375,0.198 10 false Cover 2.5,2.344 4.063,2.531 1.563,0.188 10 false A-A Cross Section 3.656,2.063 5.031,2.26 1.375,0.198 10 false Atmospheric Air 3.396,1.458 4.771,1.656 1.375,0.198 10 false Platinum Electrode 3.656,0.833 5.031,1.031 1.375,0.198 10 false Heater 3.635,0.49 5.01,0.688 1.375,0.198 10 false Alumina 1.917,0.125 3.104,0.552 1.188,0.427 10 false Solid Electrolyte (Zirconia Element) 4.854,0.104 6.208,0.552 1.354,0.448 10 false ECM Monitored A/F Sensor Voltage 5.635,2.323 7.094,2.583 1.458,0.26 10 false Air-fuel Ratio

HINT:
·

Although the DTC titles say oxygen sensor, these DTCs relate to the Air Fuel ratio (A/F) sensor.

·

Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.

·

When one of these DTCs is stored, the ECM enters fail-safe mode. The ECM turns off the A/F sensor heater in fail-safe mode. Fail-safe mode continues until the engine switch is turned off.

·

The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The A/F sensor heater circuit uses a relay on the +B side of the circuit.

A164715E39
0.054,0.046 2.664,0.305 2.609,0.259 12 Reference (System Diagram): 5.056,1.219 5.615,1.374 0.559,0.155 10 HA1A 3.965,1.239 4.523,1.394 0.559,0.155 10 HA1A 3.294,1.251 3.533,1.406 0.239,0.156 10 +B 5.056,1.735 5.504,1.900 0.448,0.164 10 A1A+ 3.984,1.775 4.432,1.940 0.448,0.164 10 A1A+ 5.056,2.485 5.541,2.645 0.485,0.160 10 A1A- 3.297,1.764 3.782,1.924 0.485,0.160 10 A1A- 1.803,2.817 3.783,3.035 1.980,0.218 10 from EFI MAIN NO. 1 Relay 3.544,1.506 4.017,1.685 0.473,0.179 10 Heater 3.528,2.04 4.001,2.233 0.473,0.193 10 Sensor 2.004,2.357 2.292,2.518 0.288,0.160 10 A/F 1.107,1.521 1.763,1.699 0.656,0.178 10 A/F HTR 3.446,2.366 4.275,2.568 0.829,0.202 10 A/F Sensor 0.265,1.236 0.791,1.623 0.526,0.387 10 from Battery 5.785,2.934 6.232,3.090 0.448,0.156 10 ECM 6.312,1.843 6.825,2.235 0.512,0.392 10 Duty Control 0.983,2.088 1.567,2.258 0.584,0.170 10 Ground



DTC Code DTC Detection Condition Trouble Area
P0031
P0051
The Air Fuel ratio (A/F) sensor heater current is below 0.8 A
(1 trip detection logic)
·

Open in Air Fuel ratio (A/F) sensor heater circuit

·

A/F sensor heater (for Sensor 1)

·

No. 2 integration relay

·

ECM


P0032
P0052
An Air Fuel ratio (A/F) sensor heater current failure
(1 trip detection logic)
·

Short in A/F sensor heater circuit

·

A/F sensor heater (for Sensor 1)

·

No. 2 integration relay

·

ECM


P101D
P103D
The heater current is higher than the specified value while the heater is not operating
(1 trip detection logic)
·

Open or short in A/F sensor heater circuit

·

ECM



MONITOR DESCRIPTION

The ECM uses information from the Air Fuel ratio (A/F) sensor to regulate the air-fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the Three-Way Catalytic Converter (TWC) to purify the exhaust gases.

The A/F sensor detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum coated zirconia and includes an integrated heating element.

The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.

The A/F sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the A/F sensor becomes inaccurate. As a result, the ECM is unable to regulate the air-fuel ratio properly.

When the current in the A/F sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores DTC(s).

Example:

The ECM stores DTC P0032 or P0052 when the current in the A/F sensor heater is more than 10 A. Conversely, when the heater current is below 0.8 A, DTC P0031 or P0051 is stored.

WIRING DIAGRAM

A351215E10
3.198,1.865 5.302,2.094 2.104,0.229 10 false NO. 2 Integration Relay 2.906,1.531 3.948,1.708 1.042,0.177 10 false EFI-MAIN NO.1 2.292,0.99 2.948,1.333 0.656,0.344 10 false EFI-MAIN NO.1 2.354,0.604 3.583,0.823 1.229,0.219 10 false A/F HTR 3.833,1.042 4.875,1.219 1.042,0.177 10 false EFI NO.2 4.844,1.135 5.302,1.333 0.458,0.198 10 false A/F 1.885,0.677 2.042,0.875 0.156,0.198 10 false 1 1.885,1.083 2.042,1.281 0.156,0.198 10 false 8 5.625,0.292 5.781,0.49 0.156,0.198 10 false 3 5.625,1.104 5.781,1.302 0.156,0.198 10 false 4 2.01,2.917 2.167,3.115 0.156,0.198 10 false 2 3.219,2.917 3.375,3.115 0.156,0.198 10 false 1 3.219,3.385 3.375,3.583 0.156,0.198 10 false 3 3.229,3.865 3.385,4.063 0.156,0.198 10 false 4 1.823,0.854 2.031,1.052 0.208,0.198 10 false 1Y 1.823,1.25 2.031,1.448 0.208,0.198 10 false 1S 5.583,0.479 5.823,0.677 0.24,0.198 10 false 1S 5.583,1.271 5.781,1.469 0.198,0.198 10 false 1S 5.406,2.99 5.688,3.177 0.281,0.188 10 false C45 5.406,3.458 5.698,3.656 0.292,0.198 10 false C45 5.406,3.938 5.719,4.125 0.313,0.188 10 false C45 2.198,2.906 2.51,3.104 0.313,0.198 10 false +B 2.813,2.906 3.427,3.104 0.615,0.198 10 false HA1A 2.802,3.396 3.417,3.594 0.615,0.198 10 false A1A+ 2.792,3.865 3.406,4.063 0.615,0.198 10 false A1A- 5.448,2.813 5.76,3.01 0.313,0.198 10 false 22 5.448,3.292 5.76,3.49 0.313,0.198 10 false 98 5.448,3.771 5.76,3.969 0.313,0.198 10 false 97 0.521,5.708 1.292,5.906 0.771,0.198 10 false P/I-B 0.656,6.948 1.333,7.167 0.677,0.219 10 false Battery 1.979,4.448 4.167,4.667 2.188,0.219 10 false A/F Sensor (for Bank 1) 1.969,6.583 4.115,6.781 2.146,0.198 10 false A/F Sensor (for Bank 2) 4.25,6.323 4.5,6.531 0.25,0.208 10 false * 5.771,2.906 6.385,3.104 0.615,0.198 10 false HA1A 5.76,3.385 6.375,3.583 0.615,0.198 10 false A1A+ 5.771,3.865 6.385,4.063 0.615,0.198 10 false A1A- 2.01,5.063 2.167,5.26 0.156,0.198 10 false 2 2.208,5.063 2.521,5.26 0.313,0.198 10 false +B 2.771,5.063 3.385,5.26 0.615,0.198 10 false HA2A 2.802,5.531 3.417,5.729 0.615,0.198 10 false A2A+ 2.792,6.021 3.406,6.219 0.615,0.198 10 false A2A- 3.229,5.063 3.385,5.26 0.156,0.198 10 false 1 3.229,5.542 3.385,5.74 0.156,0.198 10 false 3 3.24,6.021 3.396,6.219 0.156,0.198 10 false 4 5.458,4.958 5.771,5.156 0.313,0.198 10 false 45 5.406,5.438 5.719,5.635 0.313,0.198 10 false 121 5.406,5.917 5.719,6.115 0.313,0.198 10 false 120 5.479,6.781 5.792,6.979 0.313,0.198 10 false 6 5.76,5.052 6.375,5.25 0.615,0.198 10 false HA2A 5.76,5.531 6.375,5.729 0.615,0.198 10 false A2A+ 5.75,6.01 6.365,6.208 0.615,0.198 10 false A2A- 5.396,5.125 5.656,5.323 0.26,0.198 10 false C45 5.406,5.615 5.688,5.813 0.281,0.198 10 false C45 5.396,6.083 5.708,6.292 0.313,0.208 10 false C45 5.406,6.958 5.719,7.156 0.313,0.198 10 false A38 5.771,6.979 6.385,7.177 0.615,0.198 10 false MREL 6.177,7.313 6.969,7.688 0.792,0.375 10 false ECM 1.979,4.26 2.594,4.458 0.615,0.198 10 false C22 1.969,6.417 2.583,6.615 0.615,0.198 10 false C23 3.958,4.167 4.948,4.448 0.99,0.281 10 false Shielded

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
A150241E06
1.208,1.618 1.545,1.863 false 1.171,2.205 1.528,2.198 false 1.912,1.871 2.332,1.741 false 0.064,0.059 2.664,0.410 2.600,0.351 10 Component without harness connected: (A/F Sensor) 0.945,1.479 1.179,1.696 0.234,0.216 10 +B 0.09,2.638 1.519,2.834 1.429,0.196 10 *1: for Bank 1 0.09,2.991 1.519,3.186 1.429,0.196 10 *2: for Bank 2 2.869,1.711 3.095,1.910 0.227,0.199 10 *2 2.856,1.485 3.062,1.677 0.207,0.192 10 *1 0.945,2.233 1.172,2.433 0.227,0.199 10 *2 0.932,2.007 1.139,2.199 0.207,0.192 10 *1 2.366,1.517 2.793,1.705 0.427,0.189 10 HA1A 2.366,1.729 2.793,1.926 0.427,0.198 10 HA2A 0.537,2.262 0.906,2.418 0.369,0.156 10 A2A- 0.537,2.044 0.906,2.200 0.369,0.156 10 A1A-

a.

Disconnect the C22 or C23 Air Fuel ratio (A/F) sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (HA1A) - 2 (+B) 20°C (68°F) 1.6 to 3.2 Ω
1 (HA1A) - 4 (A1A-) Always 10 kΩ or higher
1 (HA2A) - 2 (+B) 20°C (68°F) 1.6 to 3.2 Ω
1 (HA2A) - 4 (A2A-) Always 10 kΩ or higher




OK

2.CHECK TERMINAL VOLTAGE (+B OF A/F SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (+B OF A/F SENSOR)
U162849E02
1.875,1.906 2.333,1.615 true 0.104,0.042 2.531,0.427 2.427,0.385 10 false Front view of wire harness connector: (to A/F Sensor) 2.375,1.51 2.604,1.729 0.229,0.219 10 false +B 0.073,2.646 1.479,2.844 1.406,0.198 10 false *1: for Bank 1 0.073,2.979 1.479,3.177 1.406,0.198 10 false *2: for Bank 2 0.75,2.063 0.979,2.26 0.229,0.198 10 false *2 0.344,2.052 0.656,2.25 0.313,0.198 10 false C23 0.729,1.719 0.938,1.906 0.208,0.188 10 false *1 0.344,1.708 0.615,1.906 0.271,0.198 10 false C22

a.

Disconnect the C22 or C23 A/F sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C22-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V
C23-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V


Result
Result Proceed to
NG A
OK B



A

3.INSPECT NO. 2 INTEGRATION RELAY (A/F)

B

5.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
3.INSPECT NO. 2 INTEGRATION RELAY (A/F)
a.

Remove the No. 2 integration relay from the engine room relay block.


b.

Inspect the No. 2 integration relay (A/F) (See page Engine / Hybrid System>3UR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY - A/F SENSOR AND BODY GROUND)

NG

REPLACE NO. 2 INTEGRATION RELAY (A/F)

4.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY - A/F SENSOR AND BODY GROUND)
a.

Disconnect the C22 or C23 A/F sensor connector.


b.

Remove the No. 2 integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C22-2 (+B) - 1S-3 Always Below 1 Ω
C23-2 (+B) - 1S-3 Always Below 1 Ω
1S-4 - Body ground Always Below 1 Ω
C22-2 (+B) or 1S-3 - Body ground Always 10 kΩ or higher
C23-2 (+B) or 1S-3 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
a.

Disconnect the C22 or C23 A/F sensor connector.


b.

Disconnect the C45 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C22-1 (HA1A) - C45-22 (HA1A) Always Below 1 Ω
C23-1 (HA2A) - C45-45 (HA2A) Always Below 1 Ω
C22-1 (HA1A) or C45-22 (HA1A) - Body ground Always 10 kΩ or higher
C23-1 (HA2A) or C45-45 (HA2A) - Body ground Always 10 kΩ or higher




OK

6.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Start the engine.


f.

Allow the engine to idle for 1 minute or more.


g.

Enter the following menus: Powertrain / Engine and ECT / DTC.


h.

Read DTCs.

Result
Result Proceed to
No DTC is output A
P0031, P0032, P0051, P0052, P101D or P103D is output B



A

B