Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/o Secondary Air Injection System) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0255032 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P0500  Vehicle Speed Sensor "A"  


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. The skid control ECU converts these wheel speed signals into a 4-pulse signal and outputs it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of these pulse signals.

A115899E04
0.43,1.047 1.579,1.425 1.149,0.378 10 from Wheel Speed Sensor 1.817,1.96 3.237,2.123 1.420,0.163 10 Skid Control ECU 3.722,1.96 5.142,2.123 1.420,0.163 10 Combination Meter 3.113,0.599 3.921,0.776 0.809,0.177 10 4-Pulse 5.039,0.599 5.848,0.776 0.809,0.177 10 4-Pulse 6.045,1.324 6.492,1.486 0.448,0.163 10 ECM

DTC Code DTC Detection Condition Trouble Area
P0500 While the vehicle is being driven, no vehicle speed sensor signal is transmitted to the ECM (2 trip detection logic).
·

Open or short in speed signal circuit

·

Combination meter

·

ECM



MONITOR DESCRIPTION

The ECM assumes that the vehicle is being driven when the indicated vehicle speed is more than 9 km/h (5.6 mph). If there is no speed signal from the combination meter despite these conditions being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.


WIRING DIAGRAM

A238382E21
5.188,2.906 6.167,3.063 0.979,0.156 10 false to Other ECUs 5.677,2.24 6.177,2.427 0.5,0.188 10 false ECM 5.938,0.875 6.188,1.042 0.25,0.167 10 false 5 V 5.198,1.125 5.521,1.281 0.323,0.156 10 false SPD 5.677,2.073 6.188,2.229 0.51,0.156 10 false A38 4.938,1.177 5.146,1.333 0.208,0.156 10 false 13 2.448,2.083 2.781,2.229 0.333,0.146 10 false E7 2.448,2.24 3.667,2.406 1.219,0.167 10 false Combination Meter 3.646,1.188 3.854,1.344 0.208,0.156 10 false +S 3.896,1.177 4.125,1.333 0.229,0.156 10 false 4 1.146,1.417 1.438,1.563 0.292,0.146 10 false SP1 2.406,1.26 2.573,1.406 0.167,0.146 10 false SI 2.219,1.26 2.427,1.417 0.208,0.156 10 false 3 0.469,2.271 1.615,2.438 1.146,0.167 10 false Skid Control ECU 0.469,2.094 0.938,2.24 0.469,0.146 10 false A24 1.542,1.24 1.927,1.396 0.385,0.156 10 false 12

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OPERATION OF SPEEDOMETER
a.

Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

HINT:
·

The vehicle speed sensor is operating normally if the speedometer reading is normal.

·

If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speedometer Malfunction).





OK

2.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPD)

NG

2.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPD)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Vehicle Speed.


e.

Drive the vehicle.


f.

Read the value displayed on the tester.

OK:

Vehicle speeds displayed on tester and speedometer display are equal.




OK

NG

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
a.

Disconnect the E7 combination meter connector.


b.

Disconnect the A38 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E7-4 (+S) - A38-13 (SPD) Always Below 1 Ω
E7-4 (+S) or A38-13 (SPD) - Body ground Always 10 kΩ or higher




OK

4.CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE)
U165843E01
1.572,2.035 1.783,2.195 0.211,0.161 10 E7 2.103,2.704 1.746,3.166 false 1.526,3.141 1.728,3.297 0.202,0.156 10 +S 0.046,0.014 2.401,0.351 2.355,0.336 10 Front view of wire harness connector: (to Combination Meter)

a.

Disconnect the E7 combination meter connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E7-4 (+S) - Body ground Engine switch on (IG) 4.5 to 5.5 V




OK

5.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL OUTPUT WAVEFORM)

NG

5.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL OUTPUT WAVEFORM)
A385686E01
1.49,1.75 2.146,2.073 true 0.031,0.021 2.25,0.406 2.219,0.385 10 false Rear view of wire harness connector: (to Combination Meter) 0.156,3.177 0.781,3.458 0.625,0.281 10 false 0 to 5 V 0.427,4.344 0.917,4.604 0.49,0.26 10 false 0V 1.458,4.354 2.469,4.667 1.01,0.313 10 false Turn Wheel 0.313,1.229 0.656,1.385 0.344,0.156 10 false E7 2.198,2.021 2.542,2.177 0.344,0.156 10 false +S

a.

Move the shift lever to N.


b.

Jack up the vehicle.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E7-4 (+S) - Body ground
·

Engine switch on (IG)

·

Wheel turned slowly


Voltage generated intermittently


HINT:

The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.




OK

NG

6.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM)
6.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM)
A385686E03
1.49,1.75 2.146,2.073 true 0.104,0.01 2.438,0.479 2.333,0.469 10 false Front view of wire harness connector: (to Combination Meter) 0.156,3.177 0.781,3.458 0.625,0.281 10 false 0 to 5 V 0.427,4.344 0.917,4.604 0.49,0.26 10 false 0V 1.458,4.354 2.469,4.667 1.01,0.313 10 false Turn Wheel 0.313,1.229 0.656,1.385 0.344,0.156 10 false E7 2.198,2.021 2.542,2.177 0.344,0.156 10 false +S

a.

Move the shift lever to N.


b.

Jack up the vehicle.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E7-3 (SI) - Body ground
·

Engine switch on (IG)

·

Wheel turned slowly


Voltage generated intermittently


HINT:

The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.




OK

REPLACE COMBINATION METER ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - SKID CONTROL ECU)
7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - SKID CONTROL ECU)
a.

Disconnect the combination meter connector.


b.

Disconnect the skid control ECU connector.


c.

Measure the resistance according the value(s) in the table below.


Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E7-3 (SI) - A24-12 (SP1) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E7-3 (SI) or A24-12 (SP1) - Body ground Always 10 kΩ or higher



OK

REPLACE MASTER CYLINDER SOLENOID

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR