The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. The skid control ECU converts these wheel speed signals into a 4-pulse signal and outputs it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of these pulse signals.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0500 | While the vehicle is being driven, no vehicle speed sensor signal is transmitted to the ECM (2 trip detection logic). | ·
Open or short in speed signal circuit ·
Combination meter ·
ECM |
The ECM assumes that the vehicle is being driven when the indicated vehicle speed is more than 9 km/h (5.6 mph). If there is no speed signal from the combination meter despite these conditions being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.
The vehicle speed sensor is operating normally if the speedometer reading is normal.
If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speedometer Malfunction).
OK
NG
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Vehicle Speed.
Drive the vehicle.
Read the value displayed on the tester.
Vehicle speeds displayed on tester and speedometer display are equal.
OK
NG
Disconnect the E119 combination meter connector.
Disconnect the A38 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E119-6 (+S) - A38-44 (SPD) | Always | Below 1 Ω |
| E119-6 (+S) or A38-44 (SPD) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the E119 combination meter connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E119-6 (+S) - Body ground | Engine switch on (IG) | 4.5 to 5.5 V |
OK
NG
Move the shift lever to N.
Jack up the vehicle.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E119-6 (+S) - Body ground | ·
Engine switch on (IG) ·
Wheel turned slowly |
Voltage generated intermittently |
The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.
OK
NG
Move the shift lever to N.
Jack up the vehicle.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E119-5 (SI) - Body ground | ·
Engine switch on (IG) ·
Wheel turned slowly |
Voltage generated intermittently |
The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.
OK
NG
Disconnect the combination meter connector.
Disconnect the skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E119-5 (SI) - A24-12 (SP1) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E119-5 (SI) or A24-12 (SP1) - Body ground | Always | 10 kΩ or higher |
OK
NG