Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/o Secondary Air Injection System) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0255032 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the GTS, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.



DTC Code DTC Detection Condition Trouble Area
P0504 Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):
(a) The engine switch is on (IG).
(b) The brake pedal is released.
(c) The STP signal is OFF when the ST1- signal is OFF.
·

Short in stop light switch signal circuit

·

STOP fuse

·

IGN fuse

·

Stop light switch

·

ECM



WIRING DIAGRAM

A179962E06
5.83,3.17 6.187,3.326 0.357,0.156 10 ECM 5.68,0.798 6.031,0.968 0.350,0.170 10 ST1- 5.684,1.552 5.993,1.708 0.309,0.156 10 STP 5.456,0.803 5.640,0.959 0.184,0.156 10 35 5.842,3.035 6.224,3.191 0.382,0.156 10 A38 5.462,1.55 5.646,1.706 0.184,0.156 10 36 4.195,1.941 4.483,2.110 0.288,0.170 10 A30 4.195,2.074 5.316,2.237 1.121,0.163 10 Stop Light Switch 5.089,0.785 5.196,0.948 0.107,0.163 10 3 5.092,1.54 5.206,1.710 0.114,0.170 10 1 3.81,1.508 3.924,1.678 0.114,0.170 10 1 4.293,0.792 4.394,0.955 0.100,0.163 10 4 4.289,1.548 4.397,1.711 0.107,0.163 10 2 4.054,1.51 4.162,1.673 0.107,0.163 10 2 3.604,0.773 3.718,0.943 0.114,0.170 10 1 3.844,0.774 3.951,0.937 0.107,0.163 10 2 3.649,1.008 3.930,1.164 0.281,0.156 10 IGN 3.793,1.765 4.213,1.920 0.420,0.156 10 STOP 2.605,1.807 2.886,1.963 0.281,0.156 10 IG2 1.428,2.437 1.785,2.593 0.357,0.156 10 IG2D 1.301,2.22 1.486,2.383 0.185,0.163 10 11 0.483,2.269 0.875,2.605 0.392,0.336 10 IG2 MAIN 3.694,3.642 3.982,3.798 0.288,0.156 10 ALT 0.651,4.791 1.140,4.974 0.489,0.184 10 Battery 2.304,2.624 2.518,2.780 0.214,0.156 10 E2 2.304,2.764 3.321,2.943 1.017,0.179 10 Main Body ECU

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

STP signal conditions can be checked using the GTS.

(a)

Connect the tester to the DLC3.

(b)

Turn the engine switch on (IG).

(c)

Turn the tester on.

(d)

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Stop Light Switch and ST1.

(e)

Check the Data List indication when the brake pedal is depressed and released.




Brake Pedal Operation Stop Light Switch ST1
Depressed ON ON
Released OFF OFF

PROCEDURE

1.CHECK STOP LIGHT SWITCH ASSEMBLY (B+ VOLTAGE)
U163883E02
0.135,0.156 2.531,0.521 2.396,0.365 10 false Front view of wire Harness connector: (to Stop Light Switch) 0.573,2.104 0.854,2.26 0.281,0.156 10 false A30

a.

Disconnect the A30 stop light switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A30-2 - Body ground Always 11 to 14 V
A30-4 - Body ground Engine switch on (IG) 11 to 14 V




OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
C171632E18
1.813,1.563 2.188,1.979 true 1.635,1.563 1.219,1.958 true 1.615,1.354 1.229,0.979 true 1.813,1.354 2.177,0.917 true 0.594,3.146 0.854,2.594 0.854,2.594 1.01,2.594 false 0.083,3.792 0.656,4.25 0.573,0.458 9 false Not Pushed 0.823,3.792 1.406,4.135 0.583,0.344 10 false Pushed 1.104,0.865 1.573,1.115 0.469,0.25 10 false 2 2.25,1.927 2.615,2.167 0.365,0.24 10 false 3 0.427,0.115 2.906,0.563 2.479,0.448 10 false Component without harness connected: (Stop Light Switch) 2.24,0.802 2.531,1.073 0.292,0.271 10 false 1 1.083,1.927 1.354,2.156 0.271,0.229 10 false 4 1.083,2.5 1.552,2.75 0.469,0.25 10 false Pin

a.

Remove the stop light switch.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Pin not pushed Below 1 Ω
Pin pushed 10 kΩ or higher
3 - 4 Pin not pushed 10 kΩ or higher
Pin pushed Below 1 Ω




OK

3.CHECK ECM (STP AND ST1 - VOLTAGE)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK ECM (STP AND ST1 - VOLTAGE)
U162824E02
1.875,3.677 2.646,3.458 true 1.781,3.688 2.573,4.396 true 1.771,0.052 2.573,0.365 0.802,0.313 10 false Brake Pedal Released 0.219,0.083 0.99,0.406 0.771,0.323 10 false Brake Pedal Depressed 0.323,1.948 2.698,2.271 2.375,0.323 10 false Front view of wire harness connector: (to ECM) 2.688,3.354 3.292,3.531 0.604,0.177 10 false 36 (STP) 2.646,4.344 3.271,4.552 0.625,0.208 10 false 35 (ST1-) 1.146,2.698 1.438,2.875 0.292,0.177 10 false A38

a.

Disconnect the A38 ECM connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A38-35 (ST1-) - Body ground Brake pedal released 11 to 14 V
Brake pedal depressed 0 to 3 V
A38-36 (STP) - Body ground Brake pedal released 0 to 3 V
Brake pedal depressed 11 to 14 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR