Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/o Secondary Air Injection System) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0255032 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P0550  Power Steering Pressure Sensor Circuit Malfunction  P0552  Power Steering Pressure Sensor Circuit Low Input  P0553  Power Steering Pressure Sensor Circuit High Input  


DESCRIPTION

The power steering oil pressure sensor is turned on when a power steering wheel load occurs by turning the steering wheel. The ECM regulates the engine idling RPM according to the voltage output of the sensor.

DTC Code DTC Detection Condition Trouble Area
P0550 Power steering oil pressure sensor voltage less than 0.28 V, or more than 4.9 V for 0.5 seconds while engine running.
(1 trip detection logic)
·

Open or short in power steering oil pressure sensor circuit

·

Power steering oil pressure sensor

·

ECM


P0552 Power steering oil pressure sensor voltage less than 0.28 V for 0.5 seconds while engine running.
(1 trip detection logic)
·

Open or short in power steering oil pressure sensor circuit

·

Power steering oil pressure sensor

·

ECM


P0553 Power steering oil pressure sensor voltage more than 4.9 V for 0.5 seconds while engine running.
(1 trip detection logic)
·

Open or short in power steering oil pressure sensor circuit

·

Power steering oil pressure sensor

·

ECM



WIRING DIAGRAM

A162851E19
0.333,3.125 3.438,3.333 3.104,0.208 10 false Power Steering Oil Pressure Sensor 5.458,3.156 5.875,3.448 0.417,0.292 10 false ECM 5.458,2.99 5.74,3.188 0.281,0.198 10 false C45 1.906,0.625 2.281,0.823 0.375,0.198 10 false PSP 1.969,1.51 2.344,1.708 0.375,0.198 10 false VC 2.01,2.438 2.385,2.635 0.375,0.198 10 false E2 5.063,0.583 5.438,0.781 0.375,0.198 10 false PSP 5.083,1.5 5.458,1.698 0.375,0.198 10 false VCV1 5.073,2.438 5.802,2.677 0.729,0.24 10 false ETHA 2.323,1.417 2.698,1.615 0.375,0.198 10 false 1 2.313,0.51 2.688,0.708 0.375,0.198 10 false 2 2.323,2.323 2.698,2.521 0.375,0.198 10 false 3 4.76,0.49 5.021,0.688 0.26,0.198 10 false 72 4.76,1.406 5.021,1.604 0.26,0.198 10 false 67 4.76,2.302 5.021,2.5 0.26,0.198 10 false 96 0.323,2.969 0.688,3.24 0.365,0.271 10 false C59

MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to regulate the engine idling speed. When the sensor output voltage deviates from the normal operating range, the ECM determines that there is a malfunction in the power steering oil pressure sensor and stores DTC(s).

CAUTION / NOTICE / HINT

HINT:
·

If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - POWER STEERING OIL PRESSURE SENSOR)
A385691E01
1.542,1.833 1.021,2.26 true 1.635,1.99 1.979,2.313 true 1.708,1.854 2.24,2.146 true 4.51,1.927 4.271,2.417 true 4.885,1.917 5.021,2.406 true 5.104,1.99 5.719,2.438 true 0.271,0.052 2.698,0.667 2.427,0.615 10 false Front view of wire harness connector: (to Power Steering Oil Pressure Sensor) 4.073,0.052 6.5,0.667 2.427,0.615 10 false Front view of wire harness connector: (to ECM) 1.49,0.969 1.927,1.25 0.438,0.281 10 false C59 0.823,2.281 1.26,2.563 0.438,0.281 10 false VC 1.948,2.333 2.385,2.615 0.438,0.281 10 false E2 2.302,2.115 2.74,2.396 0.438,0.281 10 false PSP 5.042,0.979 5.479,1.26 0.438,0.281 10 false C45 3.969,2.417 4.646,2.719 0.677,0.302 10 false 67 (VCV1) 4.781,2.417 5.458,2.719 0.677,0.302 10 false 72 (PSP) 5.781,2.417 6.458,2.719 0.677,0.302 10 false 98 (ETHA)

a.

Disconnect the C45 ECM connector.


b.

Disconnect the C59 power steering oil pressure sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C59-2 (PSP) - C45-72 (PSP) Always Below 1 Ω
C59-1 (VC) - C45-67 (VCV1) Always Below 1 Ω
C59-3 (E2) - C45-98 (ETHA) Always Below 1 Ω
C59-2 (PSP) or C45-72 (PSP) - Body ground Always 10 kΩ or higher
C59-1 (VC) or C45-67 (VCV1) - Body ground Always 10 kΩ or higher




OK

2.REPLACE POWER STEERING OIL PRESSURE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE POWER STEERING OIL PRESSURE SENSOR
a.

Replace the power steering oil pressure sensor (See page Engine / Hybrid System>3UR-FE (ENGINE CONTROL)>POWER STEERING OIL PRESSURE SWITCH>REMOVAL).



NEXT

3.CONFIRM WHETHER DTC OUTPUT RECURS
3.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.


d.

Read the DTCs.

Result
Result Proceed to
P0550, P0552 and/or P0553 are output A
No DTC is output B



A

B

END