Home › Engine / Hybrid System › 1UR-FE (ENGINE MECHANICAL) › ENGINE UNIT
RM2660E _51 Engine / Hybrid System _052776 1UR-FE ENGINE MECHANICAL _0255040 ENGINE UNIT G

1UR-FE ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 11101A 1.INSPECT CYLINDER HEAD SET BOLT

a.
A228442E01
1.695,1.001 1.880,1.156 0.185,0.155 10 *1 1.337,2.705 1.522,2.859 0.185,0.155 10 *2

Using a vernier caliper, measure the length of the cylinder head set bolt from the seat to the end.

Standard length:

141.3 to 142.7 mm (5.56 to 5.62 in.)


Maximum length:

143.7 mm (5.66 in.)


Text in Illustration
*1 Measurement Length
*2 Distance

If the length is more than the maximum, replace the cylinder head set bolt.


b.

Using a vernier caliper, measure the diameter of the elongated threads around the point indicated in the illustration.

Distance:
Item Specified Condition
Intake side bolt 103 mm (4.06 in.)
Exhaust side bolt 108 mm (4.25 in.)


Standard diameter:

10.85 to 11.00 mm (0.427 to 0.433 in.)


Minimum diameter:

10.60 mm (0.417 in.)


If the diameter is less than the minimum, replace the cylinder head set bolt.

HINT:

If a visual check reveals no excessively thin areas, check the area of the bolt around the point indicated in the illustration and find the area that has the smallest diameter.



Hide 13801 2.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Turn the roller by hand to check that it turns smoothly.

If the roller does not turn smoothly, replace the No. 1 valve rocker arm sub-assembly.


Hide 13750 3.INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
·

Keep the adjuster free from dirt and foreign objects.

·

Use only clean engine oil.



A385810E01
2.167,0.417 2.542,0.417 true 1.385,0.417 1.76,0.417 true 1.375,0.969 1.677,0.698 1.677,0.698 1.802,0.698 true 2.094,0.698 2.219,0.698 2.219,0.698 2.542,0.885 true 1.406,1.146 1.781,1.146 false 2.083,1.156 2.51,1.156 false 1.313,1.615 1.771,1.615 true 2.073,1.604 2.594,1.604 true 1.229,1.958 1.792,1.958 true 2.073,1.958 2.667,1.958 true 1.375,2.063 1.667,2.354 1.667,2.354 1.771,2.354 true 2.552,2.052 2.208,2.354 2.208,2.354 2.083,2.354 true 4.927,1.073 4.531,0.615 4.531,0.615 4.396,0.615 true 1.833,0.344 2.292,0.542 0.458,0.198 10 false SST 1.875,0.625 2.333,0.823 0.458,0.198 10 false *1 1.865,1.083 2.302,1.281 0.438,0.198 10 false *2 1.865,1.51 2.302,1.708 0.438,0.198 10 false *3 1.865,1.875 2.302,2.073 0.438,0.198 10 false *4 1.865,2.281 2.302,2.479 0.438,0.198 10 false *5 4.052,0.542 4.51,0.74 0.458,0.198 10 false SST

a.

Place the valve lash adjuster into a container full of new engine oil.

Text in Illustration
*1 Taper Part
*2 Plunger
*3 Low Pressure Chamber
*4 Check Ball
*5 High Pressure Chamber


b.

Insert the tip of SST into the valve lash adjuster plunger and use the tip to press down on the check ball inside the plunger.

SST
09276-75010  


c.

Squeeze SST and the valve lash adjuster together to move the plunger up and down 5 to 6 times.


d.

Check the movement of the plunger and bleed air.

OK:

Plunger moves up and down.


NOTICE:

When bleeding high-pressure air from the compression chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.



e.

After bleeding the air, remove SST. Then try to quickly and firmly press the plunger with your fingers.

OK:

Plunger can be pressed 3 times.


If the plunger can still be compressed after pressing it 3 times, replace the valve lash adjuster assembly with a new one.


Hide 13511 4.INSPECT CAMSHAFT SUB-ASSEMBLY

a.

Inspect the camshaft runout.

i.

Place the camshaft on V-blocks.


ii.

Using a dial indicator, measure the circle runout at the center journal.

Maximum circle runout:

0.04 mm (0.00157 in.)


If the circle runout is more than the maximum, replace the camshaft sub-assembly.

HINT:

Check the oil clearance after replacing the camshaft.




b.

Using a micrometer, measure the cam lobe height.

Standard Cam Lobe Height:
Item Specified Condition
Intake 43.456 to 43.566 mm (1.711 to 1.715 in.)
Exhaust 43.800 to 43.910 mm (1.724 to 1.729 in.)


Minimum Cam Lobe Height:
Item Specified Condition
Intake 43.406 mm (1.709 in.)
Exhaust 43.750 mm (1.722 in.)


If the cam lobe height is less than the minimum, replace the camshaft sub-assembly.


c.

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Item Specified Condition
No. 1 journal 29.956 to 29.970 mm (1.1793 to 1.1799 in.)
Other journals 25.959 to 25.975 mm (1.0220 to 1.0226 in.)


If the journal diameter is not as specified, check the oil clearance.


Hide 13050 5.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

a.

Install the camshaft bearing cap (See page Engine / Hybrid System>1UR-FE (ENGINE MECHANICAL)>CAMSHAFT>INSTALLATION).

HINT:

Only install the intake camshaft.



b.

Install the camshaft housing (See page Engine / Hybrid System>1UR-FE (ENGINE MECHANICAL)>CAMSHAFT>INSTALLATION).

HINT:

Do not use seal packing when installing the camshaft housing as the installation is temporary.



c.

Apply a light coat of engine oil to the camshaft and camshaft timing gear.


d.
A160670E06
1.15,1.062 1.741,0.16 1.741,0.16 1.888,0.16 false 0.86,0.973 1.149,1.872 1.149,1.872 1.329,1.872 false 1.927,0.083 2.112,0.238 0.185,0.155 10 *1 1.352,1.789 1.537,1.943 0.185,0.155 10 *2

Using the hexagonal portion of the camshaft, align the knock pin of the camshaft with the pin hole of the camshaft timing gear and install the camshaft timing gear.

Text in Illustration
*1 Knock Pin
*2 Pin Hole

NOTICE:
·

Do not forcefully push on the camshaft timing gear. This may cause the camshaft knock pin tip to damage the installation surface of the camshaft timing gear.

·
A160671E08
0.35,1.858 0.535,2.012 0.185,0.155 10 *1 2.105,1.812 2.290,1.967 0.185,0.155 10 *2 0.665,0.322 0.850,0.476 0.185,0.155 10 *a 0.873,0.424 0.972,0.424 0.972,0.424 1.244,0.951 false 2.061,0.301 2.246,0.456 0.185,0.155 10 *a 2.051,0.398 1.952,0.398 1.952,0.398 1.679,0.925 false 0.44,1.49 0.44,1.844 false 2.206,0.86 2.206,1.798 false 1.424,1.834 1.609,1.988 0.185,0.155 10 *a 1.514,1.51 1.514,1.82 false

Do not loosen or remove the 3 bolts shown in the illustration. If any of them are loosened or removed, the backlash of the gear in the timing tube will go out of adjustment. In this case, replace the camshaft timing gear assembly with a new one.



Text in Illustration
*1 Flange Bolt
*2 Straight Pin
*a Do not remove


e.

Apply a light coat of engine oil to the threads and under the head of the bolt.


f.
A214634E02
1.134,0.039 1.319,0.194 0.185,0.155 10 *a

Using a wrench to hold the hexagonal portion of the camshaft, install the camshaft timing gear flange bolt.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)

Text in Illustration
*a Hold
V100135

Turn


g.

Remove the camshaft bearing cap (See page Engine / Hybrid System>1UR-FE (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL).


h.

Check the lock of the camshaft timing gear.

i.

Clamp the camshaft in a vise and confirm that the camshaft timing gear is locked.

NOTICE:

Be careful not to damage the camshaft.




i.
A160672E04
0.759,1.105 0.944,1.260 0.185,0.155 10 *1 0.513,3.61 0.698,3.764 0.185,0.155 10 *a 1.565,1.195 0.965,1.195 false 2.432,1.155 2.617,1.309 0.185,0.155 10 *1 2.424,1.245 1.825,1.245 false 2.466,1.627 2.651,1.782 0.185,0.155 10 *2 2.458,1.718 2.352,1.718 2.352,1.718 1.854,1.391 false 1.227,2.062 1.411,2.217 0.185,0.155 10 *2 1.322,2.043 1.322,1.946 1.322,1.946 1.561,1.439 false 1.324,3.709 0.724,3.709 false 0.518,3.001 0.703,3.155 0.185,0.155 10 *b 1.329,3.1 0.729,3.1 false 2.693,3.501 2.878,3.655 0.185,0.155 10 *b 2.681,3.599 2.081,3.599 false 2.693,3.159 2.878,3.314 0.185,0.155 10 *a 2.681,3.258 2.003,3.258 false

Release the lock pin.

Text in Illustration
*1 Advance Side Path
*2 Retard Side Path
*a Open
*b Close
V100144

Vinyl Tape

i.

Clean the cam journal with non-residue solvent.


ii.

Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.


iii.

Break through the tape over the advance side path. Then break through the tape over the retard side path on the opposite side of the advanced side path as shown in the illustration.


iv.
A160673E02
1.824,1.13 2.415,0.889 2.415,0.889 2.557,0.889 false 0.995,0.867 1.138,0.867 1.138,0.867 1.575,1.288 false 2.593,0.8 2.778,0.954 0.185,0.155 10 *1 0.777,0.779 0.961,0.933 0.185,0.155 10 *2

Apply compressed air at approximately 200 kPa (2.0 kgf/cm2, 29 psi) to the two paths accessible through the holes in the tape.

Text in Illustration
*1 Advance Side Path
*2 Retard Side Path

NOTICE:

Cover the paths with a piece of cloth when applying pressure to keep oil from splashing.



v.
A160674E02
1.822,1.224 2.393,0.992 2.393,0.992 2.575,0.992 false 1.575,1.383 1.19,1.033 1.19,1.033 1.052,1.033 false 2.6,0.903 2.785,1.058 0.185,0.155 10 *1 0.833,0.937 1.018,1.091 0.185,0.155 10 *2 0.717,1.479 0.902,1.634 0.185,0.155 10 *a 2.465,1.327 2.650,1.482 0.185,0.155 10 *b

Check that the camshaft timing gear revolves in the advance direction when reducing the air pressure applied to the retard side path.

Text in Illustration
*1 Advance Side Path
*2 Retard Side Path
*a Decompress
*b Hold Pressure

HINT:

This operation releases the lock pin which holds the timing gear in the most retarded position.



vi.

When the camshaft timing gear reaches the most advanced position, release the air pressure from the retard side path and advance side path in that order.

NOTICE:

Do not release the air pressure from the advance side path first. The gear may abruptly shift in the retard direction and break the lock pin.




j.

Check for smooth rotation.

i.

Turn the camshaft timing gear within its movable range (21°) 2 or 3 times, but do not turn it to the most retarded position. Make sure that the gear turns smoothly.

NOTICE:

Do not use air pressure to perform the smooth rotation check.




k.

Check the lock at the most retarded position.

i.

Confirm that the camshaft timing gear becomes locked at the most retarded position.



l.

Install the camshaft bearing cap (See page Engine / Hybrid System>1UR-FE (ENGINE MECHANICAL)>CAMSHAFT>INSTALLATION).

HINT:

Only install the intake camshaft.



m.

Install the camshaft housing (See page Engine / Hybrid System>1UR-FE (ENGINE MECHANICAL)>CAMSHAFT>INSTALLATION).

HINT:

Do not use seal packing when installing the camshaft housing as the installation is temporary.



n.
A214635E02
1.136,0.023 1.321,0.178 0.185,0.155 10 *a

Hold the hexagonal portion of the camshaft with a wrench and loosen the flange bolt.

Text in Illustration
*a Hold
V100135

Turn


o.

Remove the camshaft bearing cap (See page Engine / Hybrid System>1UR-FE (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL).


p.

Remove the flange bolt and camshaft timing gear.


Hide 13080 6.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.

Install the camshaft bearing cap (See page Engine / Hybrid System>1UR-FE (ENGINE MECHANICAL)>CAMSHAFT>INSTALLATION).

HINT:

Only install the exhaust camshaft.



b.

Install the camshaft housing (See page Engine / Hybrid System>1UR-FE (ENGINE MECHANICAL)>CAMSHAFT>INSTALLATION).

HINT:

Do not use seal packing when installing the camshaft housing as the installation is temporary.



c.

Apply a light coat of engine oil to the camshaft and camshaft timing exhaust gear.


d.
A148246E07
1.515,0.812 1.178,1.553 1.178,1.553 1.05,1.553 false 0.815,0.538 1.511,0.186 1.511,0.186 1.703,0.186 false 1.732,0.097 1.917,0.252 0.185,0.155 10 *1 0.837,1.459 1.021,1.614 0.185,0.155 10 *2

Using the hexagonal portion of the camshaft, align the knock pin of the camshaft with the pin hole of the camshaft timing exhaust gear and install the camshaft timing exhaust gear.

Text in Illustration
*1 Pin Hole
*2 Knock Pin

NOTICE:
·

Do not forcefully push on the camshaft timing exhaust gear. This may cause the camshaft knock pin tip to damage the installation surface of the camshaft timing exhaust gear.

·
A148250E07
0.279,1.948 0.464,2.103 0.185,0.155 10 *1 1.647,0.423 1.831,0.578 0.185,0.155 10 *a 1.631,0.524 1.538,0.524 1.538,0.524 1.197,1.211 false 0.294,0.408 0.479,0.563 0.185,0.155 10 *a 0.507,0.51 0.6,0.51 0.6,0.51 0.941,1.196 false 1.425,1.932 1.609,2.086 0.185,0.155 10 *a 0.982,1.642 0.982,2.034 0.982,2.034 1.407,2.034 false 1.182,1.699 1.182,2.034 false 0.383,1.694 0.383,1.931 false

Do not loosen or remove the 4 bolts shown in the illustration. If any of them are loosened or removed, the backlash of the gear in the timing tube will go out of adjustment. In this case, replace the camshaft timing exhaust gear assembly with a new one.



Text in Illustration
*1 Flange Bolt
*a Do not remove


e.

Apply a light coat of engine oil to the threads and under the head of the bolt.


f.
A214636E02
0.8,0.14 0.985,0.294 0.185,0.155 10 *a

Using a wrench to hold the hexagonal portion of the camshaft, install the camshaft timing exhaust gear flange bolt.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)

Text in Illustration
*a Hold
V100135

Turn


g.

Remove the camshaft bearing cap (See page Engine / Hybrid System>1UR-FE (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL).


h.

Check the camshaft timing exhaust gear lock.

i.

Make sure that the camshaft timing exhaust gear is locked.



i.
A148247E06
2.539,0.929 2.723,1.083 0.185,0.155 10 *1 0.556,2.745 0.741,2.899 0.185,0.155 10 *b 1.896,1.014 2.517,1.014 false 2.563,1.338 2.748,1.492 0.185,0.155 10 *2 1.921,1.131 2.443,1.423 2.443,1.423 2.541,1.423 false 0.8,0.857 0.984,1.012 0.185,0.155 10 *1 1.01,0.943 1.63,0.943 false 1.288,1.744 1.473,1.899 0.185,0.155 10 *2 1.628,1.206 1.39,1.636 1.39,1.636 1.39,1.729 false 0.769,2.846 1.244,2.846 false 0.556,3.592 0.741,3.747 0.185,0.155 10 *a 0.769,3.694 1.244,3.694 false 2.723,2.981 2.908,3.136 0.185,0.155 10 *a 2.128,3.082 2.699,3.082 false 2.839,3.389 3.024,3.544 0.185,0.155 10 *b 2.253,3.49 2.825,3.49 false

Release the lock pin.

Text in Illustration
*1 Advance Side Path
*2 Retard Side Path
*a Open
*b Close
V100144

Vinyl Tape

i.

Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.


ii.

Break through the tape over the advance side path. Then break through the tape over the retard side path on the opposite side of the advanced side path as shown in the illustration.


iii.
A148248E03
2.551,0.728 2.298,0.728 2.298,0.728 1.851,0.98 false 0.921,0.578 1.143,0.578 1.143,0.578 1.583,1.168 false 2.591,0.647 2.776,0.802 0.185,0.155 10 *1 0.707,0.488 0.892,0.643 0.185,0.155 10 *2

Apply compressed air at approximately 200 kPa (2.0 kgf/cm2, 29 psi) to the two paths accessible through the holes in the tape (the advance side path and retard side path).

Text in Illustration
*1 Advance Side Path
*2 Retard Side Path

NOTICE:

Cover the paths with a piece of cloth when applying pressure to keep oil from splashing.



iv.
A148249E04
2.511,0.649 2.34,0.649 2.34,0.649 1.835,0.969 false 1.032,0.642 1.168,0.642 1.168,0.642 1.563,1.14 false 2.538,0.562 2.723,0.717 0.185,0.155 10 *1 0.818,0.55 1.003,0.705 0.185,0.155 10 *2 0.643,1.24 0.828,1.395 0.185,0.155 10 *a 2.55,1.064 2.734,1.218 0.185,0.155 10 *b

Check that the camshaft timing exhaust gear turns in the retard direction when reducing the air pressure applied to the advance side path.

Text in Illustration
*1 Advance Side Path
*2 Retard Side Path
*a Hold Pressure
*b Decompress

HINT:

The lock pin is released and the camshaft timing exhaust gear turns in the retard direction.



v.

When the camshaft timing exhaust gear moves to the most retarded position, release the air pressure from the advance side path, and then release the air pressure from the retard side path.

NOTICE:

Be sure to release the air pressure from the advance side path first. If the air pressure of the retard side path is released first, the camshaft timing exhaust gear may abruptly shift in the advance direction and break the lock pin or other parts.




j.

Check for smooth rotation.

i.

Turn the camshaft timing exhaust gear within its movable range (18.5°) 2 or 3 times, but do not turn it to the most advanced position. Make sure that the gear turns smoothly.

NOTICE:

When the air pressure is released from the advance side path and then from the retard side path, the gear automatically returns to the most advanced position, due to the advance assist spring operation, and locks. Gradually release the air pressure from the retard side path before performing the smooth rotation check.




k.

Check the lock at the most advanced position.

i.

Make sure that the camshaft timing exhaust gear becomes locked at the most advanced position.



l.

Install the camshaft bearing cap (See page Engine / Hybrid System>1UR-FE (ENGINE MECHANICAL)>CAMSHAFT>INSTALLATION).

HINT:

Only install the exhaust camshaft.



m.

Install the camshaft housing (See page Engine / Hybrid System>1UR-FE (ENGINE MECHANICAL)>CAMSHAFT>INSTALLATION).

HINT:

Do not use seal packing when installing the camshaft housing as the installation is temporary.



n.
A214637E02
0.792,0.088 0.977,0.242 0.185,0.155 10 *a

Hold the hexagonal portion of the camshaft with a wrench and loosen the flange bolt.

Text in Illustration
*a Hold
V100135

Turn


o.

Remove the camshaft bearing cap (See page Engine / Hybrid System>1UR-FE (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL).


p.

Remove the flange bolt and camshaft timing exhaust gear.


Hide 13506 7.INSPECT NO. 1 CHAIN SUB-ASSEMBLY

a.
A168044E10
0.651,1.746 0.783,1.924 0.133,0.178 10 0 0.823,1.752 0.936,1.902 0.113,0.150 10 1 1.004,1.75 1.124,1.918 0.120,0.169 10 2 1.187,1.751 1.304,1.909 0.118,0.158 10 3 1.364,1.748 1.491,1.894 0.127,0.146 10 4 1.553,1.752 1.671,1.898 0.118,0.147 10 5 2.935,1.739 3.119,1.897 0.184,0.158 10 15 1.728,1.103 1.913,1.258 0.185,0.155 10 *1

Using a spring scale, pull the chain with a force of 147 N (15 kgf, 33.1 lbf) as shown in the illustration.

Text in Illustration
*1 Measurement Area


b.

Using a vernier caliper, measure the length of 15 pins.

Maximum chain elongation:

136.9 mm (5.39 in.)


HINT:

Perform the measurement at 3 random places.


If the elongation is more than the maximum, replace the No. 1 chain sub-assembly.


Hide 13507 8.INSPECT NO. 2 CHAIN SUB-ASSEMBLY

a.

Using a spring scale, pull the chain with a force of 147 N (15 kgf, 33.1 lbf).


b.

Using a vernier caliper, measure the length of 15 pins.

Maximum chain elongation:

137.6 mm (5.42 in.)


HINT:

Perform the measurement at 3 random places.


If the elongation is more than the maximum, replace the No. 2 chain sub-assembly.


Hide 13521 9.INSPECT CRANKSHAFT TIMING SPROCKET RH

a.

Wrap the chain around the sprocket.


b.
A148252

Using a vernier caliper, measure the sprocket diameter with the chain.

Minimum sprocket diameter (with chain):

61.4 mm (2.42 in.)


HINT:

The vernier caliper must contact the chain rollers for the measurement.


If the diameter is less than the minimum, replace the chain and crankshaft timing sprocket RH.


Hide 13522S 10.INSPECT CRANKSHAFT TIMING SPROCKET LH

a.

Wrap the chain around the sprocket.


b.

Using a vernier caliper, measure the sprocket diameter with the chain.

Minimum sprocket diameter (with chain):

61.4 mm (2.42 in.)


HINT:

The vernier caliper must contact the chain rollers for the measurement.


If the diameter is less than the minimum, replace the chain and crankshaft timing sprocket LH.


Hide 13540 11.INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A148251E04
0.865,1.907 1.050,2.061 0.185,0.155 10 *1 3.189,1.347 3.374,1.502 0.185,0.155 10 *2 1.077,1.996 1.175,1.996 1.175,1.996 1.49,1.663 false 2.684,1.431 3.15,1.431 false

Move the stopper plate upward to release the lock.

Text in Illustration
*1 Stopper Plate
*2 Plunger


b.

Push the plunger and check that it moves smoothly.

If necessary, replace the No. 1 chain tensioner assembly.


Hide 13550 12.INSPECT NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A148258E04
3.041,0.351 3.226,0.506 0.185,0.155 10 *1 1.514,1.601 1.698,1.756 0.185,0.155 10 *1

Check that the plunger moves smoothly.


b.

Measure the worn depth of the chain tensioner.

Maximum depth:

0.9 mm (0.0354 in.)


Text in Illustration
*1 Depth

If the depth is more than the maximum, replace the No. 2 chain tensioner assembly.


Hide 13560A 13.INSPECT NO. 3 CHAIN TENSIONER ASSEMBLY

a.
A148259E04
3.145,0.209 3.330,0.364 0.185,0.155 10 *1 1.274,1.843 1.459,1.998 0.185,0.155 10 *1

Check that the plunger moves smoothly.


b.

Measure the worn depth of the chain tensioner.

Maximum depth:

0.9 mm (0.0354 in.)


Text in Illustration
*1 Depth

If the depth is more than the maximum, replace the No. 3 chain tensioner assembly.


Hide 13559 14.INSPECT CHAIN TENSIONER SLIPPER LH

a.
A148254E04
3.172,0.926 3.356,1.080 0.185,0.155 10 *1

Measure the worn depth of the chain tensioner slipper.

Maximum depth:

1.0 mm (0.0394 in.)


Text in Illustration
*1 Depth

If the depth is more than the maximum, replace the chain tensioner slipper LH.


Hide 13559 15.INSPECT CHAIN TENSIONER SLIPPER RH

a.
A148257E02
2.891,1.059 3.076,1.213 0.185,0.155 10 *1

Measure the worn depth of the chain tensioner slipper.

Maximum depth:

1.0 mm (0.0394 in.)


Text in Illustration
*1 Depth

If the depth is more than the maximum, replace the chain tensioner slipper RH.


Hide 13561 16.INSPECT NO. 1 CHAIN VIBRATION DAMPER LH

a.
A148255E04
3.177,0.581 3.361,0.735 0.185,0.155 10 *1

Measure the worn depth of the chain vibration damper.

Maximum depth:

1.0 mm (0.0394 in.)


Text in Illustration
*1 Depth

If the depth is more than the maximum, replace the No. 1 chain vibration damper LH.


Hide 13561 17.INSPECT NO. 1 CHAIN VIBRATION DAMPER RH

a.
A148256E04
3.087,0.974 3.272,1.129 0.185,0.155 10 *1

Measure the worn depth of the chain vibration damper.

Maximum depth:

1.0 mm (0.0394 in.)


Text in Illustration
*1 Depth

If the depth is more than the maximum, replace the No. 1 chain vibration damper RH.


Hide 17150 18.INSPECT EXHAUST MANIFOLD ASSEMBLY LH

a.
A228369

Using a precision straightedge and feeler gauge, measure the warpage of the contact surface of the cylinder head.

Maximum warpage:

0.7 mm (0.0276 in.)


If the warpage is more than the maximum, replace the exhaust manifold assembly LH.


Hide 17140 19.INSPECT EXHAUST MANIFOLD ASSEMBLY RH

a.
A228370

Using a precision straightedge and feeler gauge, measure the warpage of the contact surface of the cylinder head.

Maximum warpage:

0.7 mm (0.0276 in.)


If the warpage is more than the maximum, replace the exhaust manifold assembly RH.