Home › Engine / Hybrid System › 1UR-FE (ENGINE MECHANICAL) › CYLINDER HEAD › 2014.08–2016.08
RM2660E _51 Engine / Hybrid System _052776 1UR-FE ENGINE MECHANICAL _0255041 CYLINDER HEAD G

1UR-FE ENGINE MECHANICAL  CYLINDER HEAD  INSPECTION  


PROCEDURE

Hide 1.INSPECT CAMSHAFT OIL CLEARANCE

a.

Clean the bearing caps, camshaft housing and camshaft journals.


b.

Place the camshafts on the camshaft housing.


c.
A145569E05
1.037,0.097 1.222,0.252 0.185,0.155 10 *1 1.245,0.188 1.355,0.188 1.355,0.188 1.726,0.672 false

Lay a strip of Plastigage across each of the camshaft journals.

Text in Illustration
*1 Plastigage


d.

Install the camshaft bearing caps (See page Engine / Hybrid System>1UR-FE (ENGINE MECHANICAL)>CAMSHAFT>INSTALLATION).

NOTICE:

Do not turn the camshaft.



e.

Install the camshaft housing (See page Engine / Hybrid System>1UR-FE (ENGINE MECHANICAL)>CAMSHAFT>INSTALLATION).

NOTICE:

Do not turn the camshaft.



f.

Remove the camshaft bearing caps (See page Engine / Hybrid System>1UR-FE (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL).


g.
A160675E03
1.207,0.095 1.317,0.095 1.317,0.095 1.594,0.576 false 0.609,3.164 1.231,2.408 false 0.595,3.787 1.23,2.41 1.23,2.41 1.325,2.41 false 1.293,3.804 2.031,4.327 2.031,4.327 2.031,4.451 false 2.03,4.331 1.289,3.203 false 2.029,4.333 1.834,3.812 false 2.029,4.328 1.838,3.203 false 2.029,4.333 2.379,3.188 false 2.029,4.328 2.378,3.79 false 2.029,4.328 3.005,3.193 false 2.029,4.328 3.004,3.792 false 0.99,0.013 1.175,0.168 0.185,0.155 10 *1 1.343,2.316 1.528,2.470 0.185,0.155 10 *2 1.938,4.468 2.123,4.623 0.185,0.155 10 *3

Measure the Plastigage at its widest point.

Standard Oil Clearance:
Item Specified Condition
No. 1 journal 0.030 to 0.065 mm (0.00118 to 0.00256 in.)
Other journals 0.025 to 0.062 mm (0.000984 to 0.00244 in.)


Maximum Oil Clearance:
Item Specified Condition
No. 1 journal 0.10 mm (0.00394 in.)
Other journals 0.09 mm (0.00354 in.)


Text in Illustration
*1 Plastigage
*2 No. 1 Journal
*3 Other Journals

If the oil clearance is more than the maximum, replace the camshaft. If necessary, replace the camshaft housing sub-assembly.


Hide 2.INSPECT CAMSHAFT THRUST CLEARANCE


b.
A228412

Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

Standard thrust clearance:

0.08 to 0.135 mm (0.00315 to 0.00531 in.)


Maximum thrust clearance:

0.15 mm (0.00591 in.)


If the thrust clearance is more than the maximum, replace the camshaft housing. If the thrust surface is damaged, replace the camshaft sub-assembly.


c.

Perform the inspection above for each camshaft.


Hide 13711B 3.INSPECT COMPRESSION SPRING

HINT:

The shape of the inner compression spring determines whether the valve spring type described here is A or B.


a.
A101392

Using a vernier caliper, measure the free length of the compression spring.

Standard free length:
Type Specified Condition
Valve Spring Type A 49.69 to 53.19 mm (1.96 to 2.09 in.)
Valve Spring Type B 49.38 to 53.38 mm (1.94 to 2.10 in.)


If the free length is not as specified, replace the compression spring.


b.
A101393E04
1.213,0.106 1.398,0.260 0.185,0.155 10 *1

Valve Spring Type A:

i.

Using a steel square, measure the deviation of the inner compression spring.

Maximum deviation:

1.0 mm (0.0394 in.)


Maximum angle (reference):

2°


Text in Illustration
*1 Deviation

If the deviation is greater than the maximum, replace the spring.



c.
A319225E24
0.042,1.208 1.146,1.438 1.104,0.229 10 false 40 mm (1.57 in.) 2.323,0.396 2.563,0.615 0.24,0.219 10 false *1

Valve Spring Type B:

i.

Using a steel square, measure the deviation of the inner compression spring.

Maximum deviation:

1.0 mm (0.0394 in.)


Maximum angle (reference):

2°


Text in Illustration
*1 Deviation

If the deviation is greater than the maximum, replace the spring.



Hide 13711 4.INSPECT INTAKE VALVE

a.

Using a micrometer, measure the diameter of the valve stem.

Standard valve stem diameter:

5.470 to 5.485 mm (0.215 to 0.216 in.)



b.
A131998E02
0.435,1.71 0.620,1.864 0.185,0.155 10 *1

Using a vernier caliper, measure the valve head margin thickness.

Standard margin thickness:

1.25 mm (0.0492 in.)


Minimum margin thickness:

0.50 mm (0.0197 in.)


Text in Illustration
*1 Margin Thickness

If the margin thickness is less than the minimum, replace the intake valve.


c.

Using a vernier caliper, measure the valve overall length.

Standard overall length:

105.85 mm (4.17 in.)


Minimum overall length:

105.35 mm (4.15 in.)


If the overall length is less than the minimum, replace the intake valve.


Hide 13715 5.INSPECT EXHAUST VALVE

a.

Using a micrometer, measure the diameter of the valve stem.

Standard valve stem diameter:

5.465 to 5.480 mm (0.215 to 0.216 in.)



b.
A132001E02
0.399,1.803 0.584,1.957 0.185,0.155 10 *1

Using a vernier caliper, measure the valve head margin thickness.

Standard margin thickness:

1.4 mm (0.0551 in.)


Minimum margin thickness:

0.50 mm (0.0197 in.)


Text in Illustration
*1 Margin Thickness

If the margin thickness is less than the minimum, replace the exhaust valve.


c.

Using a vernier caliper, measure the valve overall length.

Standard overall length:

110.40 mm (4.35 in.)


Minimum overall length:

109.90 mm (4.33 in.)


If the overall length is less than the minimum, replace the exhaust valve.


Hide 6.INSPECT VALVE GUIDE BUSH OIL CLEARANCE

a.
A145559

Using a caliper gauge, measure the inside diameter of the valve guide bush.

Standard bush inside diameter:

5.51 to 5.53 mm (0.217 to 0.218 in.)



b.

Subtract the valve stem diameter measurement from the valve guide bush inside diameter measurement.

Standard Oil Clearance:
Item Specified Condition
Intake 0.025 to 0.060 mm (0.000984 to 0.00236 in.)
Exhaust 0.030 to 0.065 mm (0.00118 to 0.00256 in.)


Maximum Oil Clearance:
Item Specified Condition
Intake 0.08 mm (0.00315 in.)
Exhaust 0.10 mm (0.00394 in.)


If the oil clearance is more than the maximum, replace the valve and valve guide bush.


Hide 11131 7.INSPECT INTAKE VALVE SEAT

a.
A149128E02
1.459,1.056 1.643,1.210 0.185,0.155 10 *1

Apply a light coat of Prussian blue to the valve face.


b.

Lightly press the valve face against the intake valve seat.

HINT:

Do not rotate the valve while pressing the valve.



c.

Check the valve face and intake valve seat.

Text in Illustration
*1 Width

i.

Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.1 to 1.5 mm (0.0433 to 0.0591 in.).

If not, correct the intake valve seat.


ii.

Check that the contact surfaces of the intake valve seat and valve face are even around the entire intake valve seat.

If not, correct the intake valve seat.



Hide 11135 8.INSPECT EXHAUST VALVE SEAT

a.
A149129E02
1.358,1.038 1.543,1.193 0.185,0.155 10 *1

Apply a light coat of Prussian blue to the valve face.


b.

Lightly press the valve face against the exhaust valve seat.

HINT:

Do not rotate the valve while pressing the valve.



c.

Check the valve face and exhaust valve seat.

Text in Illustration
*1 Width

i.

Check that the contact surfaces of the exhaust valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.1 to 1.5 mm (0.0433 to 0.0591 in.).

If not, correct the exhaust valve seat.


ii.

Check that the contact surfaces of the exhaust valve seat and valve face are even around the entire exhaust valve seat.

If not, correct the exhaust valve seat.



Hide 11101 9.INSPECT CYLINDER HEAD SUB-ASSEMBLY

A385824E01
3.844,0.094 4.156,0.292 0.313,0.198 10 false *a 3.844,1.448 4.156,1.646 0.313,0.198 10 false *b 3.844,2.219 4.156,2.417 0.313,0.198 10 false *c

a.

Using a precision straightedge and feeler gauge, measure the warpage of the contact surfaces of the cylinder block and manifold.

Standard Warpage:
Item Specified Condition
Cylinder block side 0.05 mm (0.00197 in.)
Intake manifold side 0.08 mm (0.00315 in.)
Exhaust manifold side 0.05 mm (0.00197 in.)


Maximum warpage:

0.10 mm (0.00394 in.)


Text in Illustration
*a for Cylinder Block Side
*b for Intake Manifold Side
*c for Exhaust Manifold Side

If the warpage is more than the maximum, replace the cylinder head sub-assembly.


b.

Using a dye penetrant, check the intake ports, exhaust ports and cylinder head surface for cracks.

If cracked, replace the cylinder head sub-assembly.