Home › Engine / Hybrid System › 1VD-FTV (ENGINE MECHANICAL) › CYLINDER BLOCK
RM2660E _51 Engine / Hybrid System _052779 1VD-FTV ENGINE MECHANICAL _0255072 CYLINDER BLOCK A

1VD-FTV ENGINE MECHANICAL  CYLINDER BLOCK  DISASSEMBLY  


PROCEDURE

Hide 1.INSPECT CONNECTING ROD THRUST CLEARANCE

a.
A164562

Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

Standard thrust clearance:

0.14 to 0.54 mm (0.00551 to 0.0213 in.)


Maximum thrust clearance:

0.60 mm (0.0236 in.)


If the thrust clearance is more than the maximum, replace one or more connecting rods as necessary.

If necessary, replace the crankshaft.


Hide 2.REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.
A164635

Using a ridge reamer, remove all the carbon from the top of the cylinder.


b.

Uniformly loosen the connecting rod bolts, and remove the connecting rod cap with bearing.


c.

Push out the piston and connecting rod with bearing through the top of the cylinder block.

HINT:

Arrange the piston and connecting rod assemblies in the correct order.



Hide 13041 3.REMOVE CONNECTING ROD BEARING

a.
A164871

Remove the connecting rod and connecting rod cap bearings.

HINT:

Arrange the removed parts in the correct order.



Hide 13011 4.REMOVE PISTON RING SET

a.
A164601

Using a piston ring expander, remove the No. 1 and No. 2 compression rings.


b.

Using a piston ring expander, remove the oil ring.


c.

Remove the oil ring expander by hand.

HINT:

Arrange the removed parts in the correct order.



Hide 13101 5.REMOVE PISTON WITH PIN SUB-ASSEMBLY

a.
A164623

Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.

If any movement is felt, replace the piston and pin as a set.


b.
A164602

Using a screwdriver, pry out the 2 snap rings.


c.
A164823E01
0.192,0.183 0.537,0.354 0.345,0.171 10 80°C

Gradually heat the piston to approximately 80°C (176°F).


d.
A164603

Using a plastic-faced hammer and brass bar, lightly tap out the piston pin and remove the connecting rod.

HINT:
·

The piston and pin are a matched set.

·

Arrange the piston and connecting rod assemblies in the correct order.




Hide 13101 6.CLEAN PISTON

a.
A164604

Using a gasket scraper, remove the carbon from the piston top.


b.
A164605

Using a groove cleaning tool or broken ring, clean the piston ring grooves.


c.
A164842

Using solvent and a brush, thoroughly clean the piston.

NOTICE:

Do not use a wire brush.



Hide 7.INSPECT CRANKSHAFT THRUST CLEARANCE

a.
A164572

Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

Standard thrust clearance:

0.02 to 0.22 mm (0.000787 to 0.00866 in.)


Maximum thrust clearance:

0.30 mm (0.0118 in.)


If the thrust clearance is more than the maximum, replace the thrust washers as a set.

Standard thrust washer thickness:

2.44 to 2.49 mm (0.0961 to 0.0980 in.)


If necessary, replace the crankshaft.


Hide 13411 8.REMOVE CRANKSHAFT

a.
U162920E02
0.385,0.073 0.542,0.24 0.156,0.167 10 false 1 1.667,1.896 1.844,2.063 0.177,0.167 10 false 10 0.385,1.906 0.542,2.073 0.156,0.167 10 false 2 2.938,1.781 3.094,1.948 0.156,0.167 10 false 3 3.042,0.073 3.198,0.24 0.156,0.167 10 false 4 1.083,0.073 1.24,0.24 0.156,0.167 10 false 5 1.083,1.906 1.24,2.073 0.156,0.167 10 false 6 2.344,1.917 2.5,2.083 0.156,0.167 10 false 7 2.333,0.073 2.49,0.24 0.156,0.167 10 false 8 1.719,0.073 1.875,0.24 0.156,0.167 10 false 9

Using several steps, loosen and remove the 10 crankshaft bearing cap set bolts uniformly in the sequence shown in the illustration.


b.
U162922E02
0.385,0.094 0.542,0.26 0.156,0.167 10 false 1 1.667,1.896 1.844,2.063 0.177,0.167 10 false 10 0.375,1.917 0.531,2.083 0.156,0.167 10 false 2 0.781,0.688 0.958,0.854 0.177,0.167 10 false 11 2.896,1.781 3.052,1.948 0.156,0.167 10 false 3 0.781,1.333 0.958,1.5 0.177,0.167 10 false 12 3.042,0.094 3.198,0.26 0.156,0.167 10 false 4 3.208,1.188 3.385,1.354 0.177,0.167 10 false 13 1.094,0.094 1.25,0.26 0.156,0.167 10 false 5 3.208,0.792 3.385,0.958 0.177,0.167 10 false 14 1.083,1.917 1.24,2.083 0.156,0.167 10 false 6 1.458,0.677 1.635,0.844 0.177,0.167 10 false 15 2.323,1.917 2.479,2.083 0.156,0.167 10 false 7 1.458,1.323 1.635,1.49 0.177,0.167 10 false 16 2.333,0.094 2.49,0.26 0.156,0.167 10 false 8 2.729,1.323 2.906,1.49 0.177,0.167 10 false 17 1.719,0.094 1.875,0.26 0.156,0.167 10 false 9 2.74,0.688 2.917,0.854 0.177,0.167 10 false 18 2.083,0.688 2.26,0.854 0.177,0.167 10 false 19 2.083,1.323 2.26,1.49 0.177,0.167 10 false 20

Using several steps, loosen and remove the 20 crankshaft bearing cap set bolts uniformly in the sequence shown in the illustration.


c.
A164799

Remove the 2 cylinder block stiffening plates.


d.
A164847

Using 2 crankshaft bearing cap set bolts, pull out the 5 bearing caps.

NOTICE:

Take care not to damage the contact surfaces of the crankshaft bearing cap and cylinder block.


HINT:
·

Keep the lower bearing and crankshaft bearing cap as a set.

·

Arrange the crankshaft bearing caps in the correct order.




e.
A164570

Remove the crankshaft.


Hide 11011 9.REMOVE CRANKSHAFT THRUST WASHER SET

A164600

Hide 11711 10.REMOVE CRANKSHAFT BEARING

A164798E01
0.101,2.093 1.763,2.270 1.662,0.178 10 Upper Crankshaft Bearing: 0.101,0.043 1.875,0.221 1.774,0.178 10 Lower Crankshaft Bearing:

HINT:
·

Keep the upper and lower crankshaft bearings and crankshaft bearing cap as a set.

·

Arrange the crankshaft bearing caps and bearings in the correct order.



Hide 15708 11.REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A164571

Using a 5 mm hexagon wrench, remove the 4 bolts and 4 oil nozzles.


Hide 33311W 12.INSPECT INPUT SHAFT BEARING (for Manual Transmission)

a.

Turn the bearing by hand.

If the bearing is stuck or difficult to turn, replace the input shaft bearing. For removal procedures, refer to the following (See page Drivetrain>H150F (MANUAL TRANSMISSION / TRANSAXLE)>INPUT SHAFT>DISASSEMBLY) and for installation procedures, refer to the following (See page Drivetrain>H150F (MANUAL TRANSMISSION / TRANSAXLE)>INPUT SHAFT>REASSEMBLY).

HINT:

The bearing is permanently lubricated and requires no cleaning or lubrication.



Hide 11432R 13.REMOVE CYLINDER BLOCK STRAIGHT SCREW PLUG

a.
A177329E01
2.735,1.353 3.094,1.512 0.359,0.160 10 Front 0.409,3.123 0.768,3.282 0.359,0.160 10 Front

Remove the 2 straight screw plugs and 2 gaskets.